AsRock Vision3D 137D, NVidia GeForce 425 (X server conf)

George g.lister at nodeunit.com
Mon Mar 9 09:47:54 PDT 2015



On 15-03-09 04:09 PM, George wrote:
>
>
> On 15-03-09 03:26 PM, Zachary Crownover wrote:
>> DragonFlyBSD and PCBSD are not comparable as you make them right now. 
>> PCBSD takes almost everything from upstream FreeBSD and patches it 
>> slightly for their system with a lot of GUI work to make the default 
>> interface and configuration easier for you, but under the hood, it's 
>> still 99% FreeBSD. DragonFlyBSD forked from FreeBSD 11 years ago and 
>> has become it's own completely independent and separate project. 
>> There is cross pollination of code from time to time, but it has 
>> diverged greatly from FreeBSD. There is no Nvidia driver for 
>> DragonFlyBSD. The PCBSD Nvidia driver works because it's written for 
>> FreeBSD, and binaries compiled on those two will work on the other, 
>> they're using the same kernel.
>>  Vesa is sort of a last resort, and I don't remember if the nouveau 
>> is up to date at all, we don't have Nvidia support at this time.
>
> Hi Zachary,
>
> Thanks for the response actually the nv driver lists a number of 
> NVidia cards, that's probably nouveau, but unfortunately mine is not 
> on the list. BTW I am not trying to make DragonFly the same as PC-BSD 
> I know they are not I was just hoping that some drivers move over and 
> maybe I was missing an update or maybe someone has gotten the same 
> card to work.
>
> I shall give it a few more tries as I would really like to give 
> DragonFly a run as a system and see how it works for a daily driver so 
> far I am really impressed by the speed.
>
> Thanks for your time.
> Cheers,
> George
>

BTW on a slightly different angle I just went to NVidia's web site and 
downloaded the FreeBSD x86_64 driver files and they contain sources and 
instructions for FreeBSD. How would one go about porting something like 
this for DragonFly BSD??? Or maybe I should ask Francois Tigeot I saw a 
presentation he did in Sofia last year and I think he has been working 
on stuff like that?

Thanks.
George

>>
>> On Mon, Mar 9, 2015 at 2:59 AM, George <g.lister at nodeunit.com 
>> <mailto:g.lister at nodeunit.com>> wrote:
>>
>>     Hi guys,
>>
>>     I have the following question. I have an AsRock Vision 3D 137D
>>     HTPC with i3 core and an NVidia GeForce 425 card.
>>
>>     I wish to use the system for a personal desktop and some
>>     development etc.., the personal desktop is kind of a high
>>     priority for this system for me.
>>
>>     I have managed to get a sort of decent, screen uses 1600x1200
>>     instead of the 1920x1080 optimal fonts are streched etc. (I am
>>     running XFCE), config for X see below:
>>
>>     # cat /etc/X11/xorg.conf
>>     Section "ServerLayout"
>>         Identifier     "X.org Configured"
>>         Screen      0  "Screen0" 0 0
>>         InputDevice    "Mouse0" "CorePointer"
>>         InputDevice    "Keyboard0" "CoreKeyboard"
>>     EndSection
>>
>>     Section "Files"
>>         ModulePath   "/usr/local/lib/xorg/modules"
>>         FontPath     "/usr/local/lib/X11/fonts/misc/"
>>         FontPath     "/usr/local/lib/X11/fonts/TTF/"
>>         FontPath     "/usr/local/lib/X11/fonts/OTF/"
>>         FontPath     "/usr/local/lib/X11/fonts/Type1/"
>>         FontPath     "/usr/local/lib/X11/fonts/100dpi/"
>>         FontPath     "/usr/local/lib/X11/fonts/75dpi/"
>>     EndSection
>>
>>     Section "Module"
>>         Load  "glx"
>>     EndSection
>>
>>     Section "InputDevice"
>>         Identifier  "Keyboard0"
>>         Driver      "kbd"
>>     EndSection
>>
>>     Section "InputDevice"
>>         Identifier  "Mouse0"
>>         Driver      "mouse"
>>         Option      "Protocol" "auto"
>>         Option      "Device" "/dev/sysmouse"
>>         Option      "ZAxisMapping" "4 5 6 7"
>>     EndSection
>>
>>     Section "Monitor"
>>         Identifier   "Monitor0"
>>         VendorName   "Samsung"
>>         ModelName    "BX2235 23inch LCD"
>>         HorizSync 31.469-79.976 <tel:31.469-79.976>
>>         VertRefresh 56.250-75.029 <tel:56.250-75.029>
>>             Modeline     "1152x864_75.00"  104.00  1152 1224 1344
>>     1536 864 867 871 905 -hsync +vsync
>>             Modeline     "1280x800_59.81"   83.25  1280 1352 1480
>>     1680 800 803 809 831 -hsync +vsync
>>             Modeline     "1280x800_74.93"  106.25  1280 1360 1488
>>     1696 800 803 809 838 -hsync +vsync
>>             Modeline     "1280x1024_60.02"  109.00  1280 1368 1496
>>     1712 1024 1027 1034 1063 -hsync +vsync
>>             Modeline     "1280x1024_75.03"  138.75  1280 1368 1504
>>     1728 1024 1027 1034 1072 -hsync +vsync
>>         Modeline     "1440x900_59.89"  106.25  1440 1528 1672 1904 
>>     900 903 909 934 -hsync +vsync
>>             Modeline     "1440x900_74.98"  136.50  1440 1536 1688
>>     1936 900 903 909 942 -hsync +vsync
>>         Modeline     "1680x1200_60.00"  168.25  1680 1792 1968 2256
>>     1200 1203 1213 1245 -hsync +vsync
>>         Modeline     "1680x1050_59.95"  146.00  1680 1784 1960 2240
>>     1050 1053 1059 1089 -hsync +vsync
>>         Modeline     "1920x1080_60.00"  173.00  1920 2048 2248 2576
>>     1080 1083 1088 1120 -hsync +vsync
>>     EndSection
>>
>>     Section "Device"
>>             ### Available Driver options are:-
>>             ### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
>>             ### <string>: "String", <freq>: "<f> Hz/kHz/MHz",
>>             ### <percent>: "<f>%"
>>             ### [arg]: arg optional
>>             #Option     "ShadowFB"              # [<bool>]
>>             #Option     "DefaultRefresh"        # [<bool>]
>>             #Option     "ModeSetClearScreen"    # [<bool>]
>>         Identifier  "Card0"
>>         Driver      "vesa"
>>         BusID       "PCI:1:0:0"
>>     EndSection
>>
>>     Section "Screen"
>>         Identifier "Screen0"
>>         Device     "Card0"
>>         Monitor    "Monitor0"
>>         SubSection "Display"
>>             Viewport   0 0
>>             Depth     1
>>             Modes     "1152x864_75.00" "1280x800_59.81"
>>     "1280x800_74.93" "1280x1024_60.02" "1280x1024_75.03"
>>     "1440x900_59.89" "1440x900_74.98" "1680x1200_60.00"
>>     "1680x1050_59.95" "1920x1080_60.00"
>>         EndSubSection
>>         SubSection "Display"
>>             Viewport   0 0
>>             Depth     4
>>             Modes     "1152x864_75.00" "1280x800_59.81"
>>     "1280x800_74.93" "1280x1024_60.02" "1280x1024_75.03"
>>     "1440x900_59.89" "1440x900_74.98" "1680x1200_60.00"
>>     "1680x1050_59.95" "1920x1080_60.00"
>>         EndSubSection
>>         SubSection "Display"
>>             Viewport   0 0
>>             Depth     8
>>             Modes     "1152x864_75.00" "1280x800_59.81"
>>     "1280x800_74.93" "1280x1024_60.02" "1280x1024_75.03"
>>     "1440x900_59.89" "1440x900_74.98" "1680x1200_60.00"
>>     "1680x1050_59.95" "1920x1080_60.00"
>>         EndSubSection
>>         SubSection "Display"
>>             Viewport   0 0
>>             Depth     15
>>             Modes     "1152x864_75.00" "1280x800_59.81"
>>     "1280x800_74.93" "1280x1024_60.02" "1280x1024_75.03"
>>     "1440x900_59.89" "1440x900_74.98" "1680x1200_60.00"
>>     "1680x1050_59.95" "1920x1080_60.00"
>>         EndSubSection
>>         SubSection "Display"
>>             Viewport   0 0
>>             Depth     16
>>             Modes     "1152x864_75.00" "1280x800_59.81"
>>     "1280x800_74.93" "1280x1024_60.02" "1280x1024_75.03"
>>     "1440x900_59.89" "1440x900_74.98" "1680x1200_60.00"
>>     "1680x1050_59.95" "1920x1080_60.00"
>>         EndSubSection
>>         SubSection "Display"
>>             Viewport   0 0
>>             Depth     24
>>             Modes     "1152x864_75.00" "1280x800_59.81"
>>     "1280x800_74.93" "1280x1024_60.02" "1280x1024_75.03"
>>     "1440x900_59.89" "1440x900_74.98" "1680x1200_60.00"
>>     "1680x1050_59.95" "1920x1080_60.00"
>>         EndSubSection
>>     EndSection
>>
>>     I tried also the "nv" NVidia??? driver but I get back "GeForce
>>     425 not supported" the other drivers are ATI etc.. which will ot
>>     work.
>>
>>     I have tried PC-BSD 10.1 release on the machine and it has an
>>     NVidia driver which detects the card and everything looks OK on
>>     the screen. DragonFly is a FreeBSD derivative just like PC-BSD. I
>>     am wondering whether the driver has not been ported yet?? I have
>>     used PC-BSD and it is very nice but it is kind of too slow
>>     (compared to Ubuntu on the same machine) and I am having some
>>     issues accessing an NetBSD NFS server it hangs with timeouts on
>>     lockd ... anyway long story short. I decided to give DragonFly a
>>     try and it is smocking fast to boot to shutdown to install
>>     packages etc. ... if I could only get X setup it would be great.
>>     Then I can move on to fighting HP printing etc. ;).
>>
>>     Here is a dmesg from the machine:
>>
>>     $ dmesg
>>     Copyright (c) 2003-2014 The DragonFly Project.
>>     Copyright (c) 1992-2003 The FreeBSD Project.
>>     Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992,
>>     1993, 1994
>>         The Regents of the University of California. All rights reserved.
>>     DragonFly v4.0.3-RELEASE #27: Thu Jan 22 17:19:56 PST 2015
>>     root at pkgbox64.dragonflybsd.org:/usr/obj/build/home/justin/src/sys/X86_64_GENERIC
>>     TSC invariant clock: 2409543436 <tel:2409543436> Hz, i8254 clock:
>>     1193223 Hz
>>     CPU: Intel(R) Core(TM) i3 CPU       M 370  @ 2.40GHz (2409.47-MHz
>>     K8-class CPU)
>>       Origin = "GenuineIntel"  Id = 0x20655  Stepping = 5
>>     Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
>>     Features2=0x9ae3bd<SSE3,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,POPCNT>
>>       AMD Features=0x28100800<SYSCALL,NX,RDTSCP,LM>
>>       AMD Features2=0x1<LAHF>
>>       Thermal and PM Features=0x5<SENSOR,ARAT>
>>       MONITOR/MWAIT Features=0x3<CST,INTBRK>
>>     real memory  = 6433078272 (6135 MB)
>>     avail memory = 6023581696 <tel:6023581696> (5744 MB)
>>     lapic: divisor index 0, frequency 66929700 Hz
>>     Initialize MI interrupts
>>     TSC testing MP synchronization ...
>>     TSC is MP synchronized
>>     TSC: cputimer freq 75296071, shift 5
>>     FQ scheduler policy version 1.1 loaded
>>     wdog: In-kernel automatic watchdog reset enabled
>>     kbd1 at kbdmux0
>>     disk scheduler: set policy of vn0 to noop
>>     disk scheduler: set policy of vn1 to noop
>>     disk scheduler: set policy of vn2 to noop
>>     disk scheduler: set policy of vn3 to noop
>>     disk scheduler: set policy of md0 to noop
>>     md0: Malloc disk
>>     ACPI: RSDP 0x00000000000F9EF0 000014 (v00 ACPIAM)
>>     ACPI: RSDT 0x00000000D3770000 000044 (v01 102410 RSDT1223
>>     20101024 MSFT 00000097)
>>     ACPI: FACP 0x00000000D3770200 000084 (v01 A_M_I  OEMFACP 12000601
>>     MSFT 00000097)
>>     ACPI: DSDT 0x00000000D3770460 0074A4 (v01 AS388  AS388115
>>     00000115 INTL 20051117)
>>     ACPI: FACS 0x00000000D3780000 000040
>>     ACPI: APIC 0x00000000D3770390 00008C (v01 102410 APIC1223
>>     20101024 MSFT 00000097)
>>     ACPI: MCFG 0x00000000D3770420 00003C (v01 102410 OEMMCFG 20101024
>>     MSFT 00000097)
>>     ACPI: OEMB 0x00000000D3780040 000072 (v01 102410 OEMB1223
>>     20101024 MSFT 00000097)
>>     ACPI: AAFT 0x00000000D377A460 000027 (v01 102410 OEMAAFT 20101024
>>     MSFT 00000097)
>>     ACPI: HPET 0x00000000D377A490 000038 (v01 102410 OEMHPET 20101024
>>     MSFT 00000097)
>>     ACPI: ASF! 0x00000000D377A4D0 000099 (v32 LEGEND I865PASF
>>     00000001 INTL 20051117)
>>     ACPI: SSDT 0x00000000D37815F0 000363 (v01 DpgPmm CpuPm 00000012
>>     INTL 20051117)
>>     cryptosoft0: <software crypto> on motherboard
>>     aesni0: No AESNI support.
>>     padlock0: No ACE support.
>>     rdrand0: No RdRand support.
>>     acpi0: <102410 RSDT1223> on motherboard
>>     ACPI: All ACPI Tables successfully acquired
>>     ACPI FADT: SCI testing interrupt mode ...
>>     ACPI FADT: SCI select level/high
>>     ACPI: Executed 1 blocks of module-level executable AML code
>>     objcache_reclaimlist
>>     objcache_reclaimlist
>>     objcache_reclaimlist
>>     objcache_reclaimlist
>>     acpi0: Power Button (fixed)
>>     Warning: ACPI is disabling APM's device.  You can't run both
>>     acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
>>     acpi_hpet0: <High Precision Event Timer> iomem
>>     0xfed00000-0xfed003ff on acpi0
>>     acpi_hpet0: frequency 14318180
>>     pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
>>     pci0: <ACPI PCI bus> on pcib0
>>     pcib1: <ACPI PCI-PCI bridge> irq 16 at device 1.0 on pci0
>>     pci1: <ACPI PCI bus> on pcib1
>>     pcib1: No _PRT found, routing with pci
>>     pcib1: No _PRT found, routing with pci
>>     vgapci0: <VGA-compatible display> port 0xdc00-0xdc7f mem
>>     0xd6000000-0xd7ffffff,0xd8000000-0xdfffffff,0xfa000000-0xfaffffff
>>     irq 16 at device 0.0 on pci1
>>     vgapci0: Boot video device
>>     pci1: <multimedia, HDA> (vendor 0x10de, dev 0x0bea) at device 0.1
>>     irq 17
>>     pci0: <dasp> (vendor 0x8086, dev 0x0050) at device 4.0 irq 16
>>     ehci0: <Intel PCH USB 2.0 controller USB-B> mem
>>     0xf9ff8000-0xf9ff83ff irq 16 at device 26.0 on pci0
>>     usbus0: EHCI version 1.0
>>     usbus0: <Intel PCH USB 2.0 controller USB-B> on ehci0
>>     pci0: <multimedia, HDA> (vendor 0x8086, dev 0x3b56) at device
>>     27.0 irq 22
>>     pcib2: <ACPI PCI-PCI bridge> irq 17 at device 28.0 on pci0
>>     pci2: <ACPI PCI bus> on pcib2
>>     re0: <RealTek 8111/8168 PCIe Gigabit Ethernet> port 0xe800-0xe8ff
>>     mem 0xf8ff8000-0xf8ffbfff,0xf8fff000-0xf8ffffff irq 16 at device
>>     0.0 on pci2
>>     re0: Hardware rev. 0x2c000000; PCI-E 125MHz
>>     miibus0: <MII bus> on re0
>>     rgephy0: <8211B/RTL8169S/8110S media interface> on miibus0
>>     rgephy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX,
>>     1000baseT, 1000baseT-FDX, auto
>>     usbus0: 480Mbps High Speed USB v2.0
>>     re0: MAC address: e0:69:95:1f:6d:81
>>     pcib3: <ACPI PCI-PCI bridge> irq 16 at device 28.1 on pci0
>>     pci3: <ACPI PCI bus> on pcib3
>>     xhci0: <NEC uPD720200 USB 3.0 controller> mem
>>     0xfbdfe000-0xfbdfffff irq 17 at device 0.0 on pci3
>>     ugen0.1: <Intel> at usbus0
>>     uhub0: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on
>>     usbus0
>>     xhci0: 32 byte context size.
>>     usbus1 on xhci0
>>     pcib4: <ACPI PCI-PCI bridge> irq 18 at device 28.2 on pci0
>>     pci4: <ACPI PCI bus> on pcib4
>>     ath0: <Atheros 9287> mem 0xfbef0000-0xfbefffff irq 18 at device
>>     0.0 on pci4
>>     usbus1: 5.0Gbps Super Speed USB v3.0
>>     ugen1.1: <0x1033> at usbus1
>>     uhub1: <0x1033 XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1>
>>     on usbus1
>>     ath0: AR9287 mac 384.2 RF5133 phy 15.15
>>     ath0: 2GHz radio: 0x0000; 5GHz radio: 0x00c0
>>     pcib5: <ACPI PCI-PCI bridge> irq 19 at device 28.3 on pci0
>>     pci5: <ACPI PCI bus> on pcib5
>>     xhci1: <XHCI (generic) USB 3.0 controller> mem
>>     0xfbff0000-0xfbffffff irq 19 at device 0.0 on pci5
>>     xhci1: 32 byte context size.
>>     usbus2 on xhci1
>>     usbus2: 5.0Gbps Super Speed USB v3.0
>>     ehci1: <Intel PCH USB 2.0 controller USB-A> mem
>>     0xf9ff2000-0xf9ff23ff irq 23 at device 29.0 on pci0
>>     usbus3: EHCI version 1.0
>>     ugen2.1: <0x1b73> at usbus2
>>     uhub2: <0x1b73 XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1>
>>     on usbus2
>>     usbus3: <Intel PCH USB 2.0 controller USB-A> on ehci1
>>     usbus3: 480Mbps High Speed USB v2.0
>>     pcib6: <ACPI PCI-PCI bridge> at device 30.0 on pci0
>>     pci6: <ACPI PCI bus> on pcib6
>>     isab0: <PCI-ISA bridge> at device 31.0 on pci0
>>     isa0: <ISA bus> on isab0
>>     atapci0: <Intel ATA controller> port
>>     0xc080-0xc08f,0xc400-0xc40f,0xc480-0xc483,0xc800-0xc807,0xc880-0xc883,0xcc00-0xcc07
>>     irq 19 at device 31.2 on pci0
>>     ata2: <ATA channel 0> on atapci0
>>     ugen3.1: <Intel> at usbus3
>>     uhub3: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on
>>     usbus3
>>     disk scheduler: set policy of ad4 to noop
>>     ad4: 953869MB <TOSHIBA MQ01ABD100 AX001A> at ata2-master UDMA33
>>     ata3: <ATA channel 1> on atapci0
>>     uhub2: 2 ports with 2 removable, self powered
>>     pci0: <serial bus, SMBus> (vendor 0x8086, dev 0x3b30) at device
>>     31.3 irq 18
>>     atapci1: <Intel ATA controller> port
>>     0xb080-0xb08f,0xb400-0xb40f,0xb480-0xb483,0xb800-0xb807,0xb880-0xb883,0xbc00-0xbc07
>>     irq 19 at device 31.5 on pci0
>>     ata4: <ATA channel 0> on atapci1
>>     uhub1: 4 ports with 4 removable, self powered
>>     unknown: timeout waiting for read DRQ
>>     unknown: timeout waiting for read DRQ
>>     disk scheduler: set policy of acd0 to noop
>>     acd0: DVDR <Slimtype DVD A DL8ATS/XAB2> at ata4-master UDMA33
>>     ata5: <ATA channel 1> on atapci1
>>     uhub3: 8 ports with 8 removable, self powered
>>     acpi_button0: <Power Button> on acpi0
>>     cpu0: <ACPI CPU> on acpi0
>>     ACPI: Dynamic OEM Table Load:
>>     ACPI: SSDT 0xFFFFFFE03FACB600 001028 (v01 DpgPmm P001Ist 00000011
>>     INTL 20051117)
>>     ACPI: Dynamic OEM Table Load:
>>     ACPI: SSDT 0xFFFFFFE0B6167380 0004F4 (v01 PmRef  P001Cst 00003001
>>     INTL 20051117)
>>     cpu_cst0: <ACPI CPU C-State> on cpu0
>>     cpu_pst0: <ACPI CPU P-State> on cpu0
>>     clockmod0: <CPU clock modulation> on cpu0
>>     coretemp0: <CPU On-Die Thermal Sensors> on cpu0
>>     cpu1: <ACPI CPU> on acpi0
>>     cpu_cst1: <ACPI CPU C-State> on cpu1
>>     cpu_pst1: <ACPI CPU P-State> on cpu1
>>     clockmod1: <CPU clock modulation> on cpu1
>>     coretemp1: <CPU On-Die Thermal Sensors> on cpu1
>>     cpu2: <ACPI CPU> on acpi0
>>     cpu_cst2: <ACPI CPU C-State> on cpu2
>>     cpu_pst2: <ACPI CPU P-State> on cpu2
>>     clockmod2: <CPU clock modulation> on cpu2
>>     coretemp2: <CPU On-Die Thermal Sensors> on cpu2
>>     cpu3: <ACPI CPU> on acpi0
>>     cpu_cst3: <ACPI CPU C-State> on cpu3
>>     cpu_pst3: <ACPI CPU P-State> on cpu3
>>     clockmod3: <CPU clock modulation> on cpu3
>>     coretemp3: <CPU On-Die Thermal Sensors> on cpu3
>>     ACPI: Enabled 4 GPEs in block 00 to 3F
>>     pmtimer0 on isa0
>>     atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
>>     atkbd0: <AT Keyboard> irq 1 on atkbdc0
>>     kbd0 at atkbd0
>>     ugen3.2: <vendor 0x8087> at usbus3
>>     uhub4: <vendor 0x8087 product 0x0020, class 9/0, rev 2.00/0.00,
>>     addr 2> on usbus3
>>     vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff
>>     on isa0
>>     sc0: <System console> at flags 0x100 on isa0
>>     sc0: VGA <16 virtual consoles, flags=0x300>
>>     lm0: <Winbond W83627DHG Hardware Monitor> at port 0x290-0x297 on isa0
>>     sio0: can't drain, serial port might not exist, disabling
>>     sio1: can't drain, serial port might not exist, disabling
>>     ppc0: cannot reserve I/O port range
>>     hpt27xx: no controller detected.
>>     CAM: Configuring 4 busses
>>     CAM: finished configuring all busses
>>     disk scheduler: set policy of cd0 to noop
>>     cd0 at ata2 bus 0 target 0 lun 0
>>     cd0: <Slimtype DVD A  DL8ATS XAB2> Removable CD-ROM SCSI-0 device
>>     cd0: 33.000MB/s transfers
>>     cd0: Attempt to query device size failed: NOT READY, Medium not
>>     present - tray open
>>     uhub4: 8 ports with 8 removable, self powered
>>     intr 19 on cpu3 at 40001/40000 hz, livelocked limit engaged!
>>     ugen3.3: <vendor 0x05e3> at usbus3
>>     uhub5: <vendor 0x05e3 USB2.0 Hub, class 9/0, rev 2.00/77.64, addr
>>     3> on usbus3
>>     uhub0: 6 ports with 6 removable, self powered
>>     uhub5: 4 ports with 4 removable, self powered
>>     ugen0.2: <vendor 0x8087> at usbus0
>>     uhub6: <vendor 0x8087 product 0x0020, class 9/0, rev 2.00/0.00,
>>     addr 2> on usbus0
>>     ugen3.4: <vendor 0x05e3> at usbus3
>>     uhub7: <vendor 0x05e3 USB2.0 Hub, class 9/0, rev 2.00/77.64, addr
>>     4> on usbus3
>>     uhub6: 6 ports with 6 removable, self powered
>>     uhub7: 4 ports with 4 removable, self powered
>>     ugen0.3: <Logitech> at usbus0
>>     ukbd0: <Logitech USB Receiver, class 0/0, rev 2.00/12.01, addr 3>
>>     on usbus0
>>     kbd2 at ukbd0
>>     ums0: <Logitech USB Receiver, class 0/0, rev 2.00/12.01, addr 3>
>>     on usbus0
>>     ums0: 16 buttons and [XYZT] coordinates ID=2
>>     uhid0: <Logitech USB Receiver, class 0/0, rev 2.00/12.01, addr 3>
>>     on usbus0
>>     ugen3.5: <vendor 0x05e3> at usbus3
>>     uhub8: <vendor 0x05e3 USB2.0 Hub, class 9/0, rev 2.00/9.01, addr
>>     5> on usbus3
>>     uhub8: 4 ports with 4 removable, self powered
>>     no B_DEVMAGIC (bootdev=0)
>>     ugen3.6: <vendor 0x05e3> at usbus3
>>     uhub9: <vendor 0x05e3 USB2.0 Hub, class 9/0, rev 2.00/9.01, addr
>>     6> on usbus3
>>     uhub9: 4 ports with 4 removable, self powered
>>     ugen3.7: <HP> at usbus3
>>     umass0: <HP Photosmart B110 series, class 0/0, rev 2.00/1.00,
>>     addr 7> on usbus3
>>     disk scheduler: set policy of da8 to noop
>>     da8 at umass-sim0 bus 0 target 0 lun 0
>>     da8: <HP Photosmart B110 1.00> Removable Direct Access SCSI-5 device
>>     da8: 40.000MB/s transfers
>>     da8: Attempt to query device size failed: NOT READY, Medium not
>>     present
>>     Mounting root from hammer:serno/23BBPJN0T.s1d
>>     HAMMER(ROOT) recovery check seqno=00233441
>>     HAMMER(ROOT) recovery range 300000000a56b9d8-300000000a56b9d8
>>     HAMMER(ROOT) recovery nexto 300000000a56b9d8 endseqno=00233442
>>     HAMMER(ROOT) mounted clean, no recovery needed
>>     DMA space used: 12416k, remaining available: 16384k
>>     Mounting devfs
>>     ugen3.8: <vendor 0x05e3> at usbus3
>>     uhub10: <vendor 0x05e3 USB Hub 2.0, class 9/0, rev 2.00/7.02,
>>     addr 8> on usbus3
>>     uhub10: 4 ports with 4 removable, self powered
>>     ugen3.9: <Prolific Technology Inc.> at usbus3
>>     ugen3.10: <Prolific Technology Inc.> at usbus3
>>     ugen3.11: <Logitech> at usbus3
>>     ums1: <Logitech USB-PS2 Optical Mouse, class 0/0, rev 2.00/27.30,
>>     addr 11> on usbus3
>>     ums1: 8 buttons and [XYZT] coordinates ID=0
>>     ugen3.12: <Darfon> at usbus3
>>     ukbd1: <Darfon USB Combo Keyboard, class 0/0, rev 1.10/2.02, addr
>>     12> on usbus3
>>     kbd3 at ukbd1
>>     uhid1: <Darfon USB Combo Keyboard, class 0/0, rev 1.10/2.02, addr
>>     12> on usbus3
>>     ulpt0: <HP Photosmart B110 series, class 0/0, rev 2.00/1.00, addr
>>     7> on usbus3
>>     ulpt0: using bi-directional mode
>>     ucom init
>>     uplcom0: <Prolific Technology Inc. USB-Serial Controller, class
>>     0/0, rev 1.10/3.00, addr 10> on usbus3
>>     attach tty
>>     malloc:
>>     uplcom1: <Prolific Technology Inc. USB-Serial Controller, class
>>     0/0, rev 1.10/3.00, addr 9> on usbus3
>>     attach tty
>>     malloc:
>>     ugen3.11: <Logitech> at usbus3 (disconnected)
>>     ums1: at uhub4, port 4, addr 11 (disconnected)
>>     ums1: detached
>>     ugen3.12: <Darfon> at usbus3 (disconnected)
>>     ukbd1: at uhub4, port 5, addr 12 (disconnected)
>>     ukbd1: detached
>>     uhid1: at uhub4, port 5, addr 12 (disconnected)
>>     uhid1: detached
>>
>>     If someone can give me a pointer from what I have provided here
>>     that would be great.
>>     Thank you for making DragonFly!
>>     Cheers,
>>     George
>>
>>
>>
>>
>> -- 
>> Sincerely,
>>
>> Zachary Crownover
>

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.dragonflybsd.org/pipermail/users/attachments/20150309/9bbd4f6c/attachment-0002.htm>


More information about the Users mailing list