Toshiba Satellite M50 ethernet undetected

Sepherosa Ziehau sepherosa at gmail.com
Mon Sep 11 23:36:03 PDT 2006 

ath(4) is not in kernel, please try following:
kldload ath_hal
kldload ath_rate
kldload if_ath
If it does not help, please post the output of "pciconf -lv"

Best Regards,
sephe
On 9/11/06, Ferruccio Zamuner <nonsolosoft at xxxxxxxx> wrote:
Copyright (c) 2003, 2004, 2005, 2006 The DragonFly Project.
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
DragonFly 1.6.1-RELEASE #0: Tue Sep  5 15:16:32 CEST 2006
    root at xxxxxxxxxxxxxxxxxxxxxx:/usr/obj/usr/src/sys/GENERIC
TSC clock: 1496258561 Hz, i8254 clock: 1193188 Hz
CPU: Intel(R) Celeron(R) M processor         1.50GHz (1496.26-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x6d8  Stepping = 8
  Features=0xafe9fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,TM,PBE>
real memory  = 527302656 (514944K bytes)
avail memory = 499777536 (488064K bytes)
Preloaded elf kernel "/kernel" at 0xc0736000.
Preloaded elf module "/modules/acpi.ko" at 0xc0736328.
Pentium Pro MTRR support enabled
md0: Malloc disk
pcibios: BIOS version 2.10
npx0: <math processor> on motherboard
npx0: INT 16 interface
Using XMM optimized bcopy/copyin/copyout
acpi0: <TOSCPL   RSDT> on motherboard
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi0: Power Button (fixed)
Warning: ACPI is disabling APM's device.  You can't run both
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
cpu0: <ACPI CPU (3 Cx states)> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button0: <Power Button> on acpi0
acpi_acad0: <AC Adapter> on acpi0
acpi_ec0: <Embedded Controller: GPE 0x1d> port 0x66,0x62 on acpi0
isab0: <ACPI Generic ISA bridge> on acpi0
acpi_cmbat0: <Control Method Battery> on acpi0
legacypci0 on motherboard
pcib0: <Host to PCI bridge> on legacypci0
pci0: <PCI bus> on pcib0
pci0: <Intel model 2592 VGA-compatible display device> at 2.0 irq 10
pci0: <unknown card> (vendor=0x8086, dev=0x2792) at 2.1
pcib1: <PCI to PCI bridge (vendor=8086 device=2660)> irq 10 at device 28.0 on pci0
pci2: <PCI bus> on pcib1
pci2: <unknown card> (vendor=0x11ab, dev=0x4351) at 0.0 irq 10
uhci0: <Intel 82801FB (ICH6) USB controller USB-A> port 0x1820-0x183f irq 11 at device 29.0 on pci0
usb0: <Intel 82801FB (ICH6) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801FB (ICH6) USB controller USB-B> port 0x1840-0x185f irq 11 at device 29.1 on pci0
usb1: <Intel 82801FB (ICH6) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801FB (ICH6) USB controller USB-C> port 0x1860-0x187f irq 11 at device 29.2 on pci0
usb2: <Intel 82801FB (ICH6) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhci3: <Intel 82801FB (ICH6) USB controller USB-D> port 0x1880-0x189f irq 10 at device 29.3 on pci0
usb3: <Intel 82801FB (ICH6) USB controller USB-D> on uhci3
usb3: USB revision 1.0
uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
pci0: <USB controller> at 29.7 irq 11
pcib2: <PCI to PCI bridge (vendor=8086 device=2448)> at device 30.0 on pci0
pci6: <PCI bus> on pcib2
pci6: <unknown card> (vendor=0x168c, dev=0x001a) at 2.0 irq 11
cbb0: <TI4510 PCI-CardBus Bridge> mem 0xb8014000-0xb8014fff irq 10 at device 4.0 on pci6
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
fwohci0: vendor=104c, dev=8029
fwohci0: <1394 Open Host Controller Interface> mem 0xb8010000-0xb8013fff,0xb8015000-0xb80157ff irq 10 at device 4.1 on pci6
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channel is 4.
fwohci0: EUI64 00:02:3f:55:75:40:37:67
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
fwe0: MAC address: 02:02:3f:40:37:67
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
pci0: <unknown card> (vendor=0x8086, dev=0x266e) at 30.2 irq 10
pci0: <unknown card> (vendor=0x8086, dev=0x266d) at 30.3 irq 11
isab1: <PCI to ISA bridge (vendor=8086 device=2641)> at device 31.0 on pci0
isa0: <ISA bus> on isab1
atapci0: <Generic PCI ATA controller> port 0x18b0-0x18bf,0-0x3,0-0x7,0-0x3,0-0x7 at device 31.2 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pci0: <unknown card> (vendor=0x8086, dev=0x266a) at 31.3 irq 11
orm0: <Option ROMs> at iomem 0xc0000-0xce7ff,0xce800-0xcf7ff,0xdc000-0xdffff on isa0
pmtimer0 on isa0
fdc0: ready for input in output
fdc0: cmd 3 failed at out byte 1 of 3
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model GlidePoint, device ID 0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0: can't drain, serial port might not exist, disabling
sio1: can't drain, serial port might not exist, disabling
ppc0: parallel port not found.
ad0: 38154MB <TOSHIBA MK4025GAS> [77520/16/63] at ata0-master BIOSDMA
acd0: DVD-R <MATSHITADVD-RAM UJ-840S> at ata1-master PIO4
Mounting root from ufs:/dev/ad0s2a
cd0 at ata1 bus 0 target 0 lun 0
cd0: <MATSHITA DVD-RAM UJ-840S 1.52> Removable CD-ROM SCSI-0 device
cd0: 16.000MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not present
Even if I kldload ath_hal.ko, ethernet is not detected.

Here there is a dmesg part from FreeBSD-CURRENT:

Copyright (c) 1992-2006 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD 7.0-CURRENT-200608 #0: Tue Aug  8 09:05:08 UTC 2006
    root at xxxxxxxxxxxxxxxxxxxxxxx:/usr/obj/usr/src/sys/GENERIC
WARNING: WITNESS option enabled, expect reduced performance.
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Celeron(R) M processor         1.50GHz (1496.26-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x6d8  Stepping = 8
  Features=0xafe9fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,TM,PBE>
real memory  = 527302656 (502 MB)
avail memory = 498024448 (474 MB)
ACPI APIC Table: <INTEL  ALVISO  >
ioapic0: Changing APIC ID to 1
ioapic0 <Version 2.0> irqs 0-23 on motherboard
kbd1 at kbdmux0
ath_hal: 0.9.17.2 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
[...]
ath0: <Atheros 5212> mem 0xb8000000-0xb800ffff irq 22 at device 2.0 on pci6
ath0: Ethernet address: 00:11:f5:64:16:62
ath0: mac 7.8 phy 4.5 radio 5.6
While the whole file now is on:
http://rafb.net/paste/results/MYd1GA24.html


--
Live Free or Die

More information about the Bugs mailing list