urtwn0 - driver didn't set altq_maxlen

karu.pruun karu.pruun at gmail.com
Sun Apr 19 05:01:40 PDT 2020


Just for completeness, this is all I have in /etc/rc.conf for wifi:

---
# dhcpcd
dhcpcd_enable="YES"

# realtek usb wifi
if_urtwn_load="YES"

# wpa_supplicant
wpa_supplicant_program="/usr/local/sbin/wpa_supplicant"

# wlan
wlans_urtwn0="wlan0"
ifconfig_wlan0="WPA"
---

Peeter

--


On Sun, Apr 19, 2020 at 2:58 PM karu.pruun <karu.pruun at gmail.com> wrote:
>
> Hello
>
> I have the same usb wifi stick, and I see the same error, but that
> does not prevent it from working. Can you check that the rest of the
> setup in /etc/rc.conf is fine? I have
>
> dhcpcd_enable="YES"
>
> and the rest is the urtwn, wlans and wpa_supplicant as in the
> handbook. Check that the wpa_supplicant connects. Check that the
> dhcpcd is running; or restart it to be sure.
>
> Cheers
>
> Peeter
>
> --
>
>
> On Mon, Apr 13, 2020 at 11:35 PM Ron Georgia <netverbs at gmail.com> wrote:
> >
> > All,
> >
> > I have a USB Wifi adapter (MAC/BB RTL8188CUS, RF 6052 1T1R) that is
> > having problems initializing. I did do some poking around and updated
> > loader.conf (see below) but that does not seem to help. When I do and
> > ifconfig wlan0 I see the SSID, but not IPv4, instead I see a "driver
> > didn't set altq_maxlen" error. This is not a new USB adapter, maybe 3 or
> > 4 years old. I am able to scan the networks with ifconfig wlan0 scan,
> > but I cannot connect to my home network (yes, the password is correct.)
> > Not sure what might be needed. I can post my full dmesg in paste bin if
> > that helps.
> >
> > Some Info:
> >
> > % ifconfig | grep -B3 -i wireless
> >      country US authmode WPA2/802.11i privacy ON deftxkey UNDEF
> >      AES-CCM 3:128-bit txpower 0 bmiss 7 scanvalid 60 protmode CTS wme
> >      roaming MANUAL
> >      media: IEEE 802.11 Wireless Ethernet OFDM/54Mbps mode 11g
> >
> > % sysctl net.wlan.devices
> > net.wlan.devices: urtwn0
> >
> > filtered dmesg:
> >
> > ess: 74:da:38:41:1c:68
> > rgeorgia at mini01% dmesg | grep urtw
> > urtwn0: <vendor 0x7392 product 0x7811, class 0/0, rev 2.00/2.00, addr 4>
> > on usbus0
> > urtwn0: MAC/BB RTL8188CUS, RF 6052 1T1R
> > urtwn0: enabling 11n
> > urtwn-rtl8192cfwT: You need to read the LICENSE file in
> > /usr/share/doc/legal/realtek/.
> > urtwn-rtl8192cfwT: If you agree with the license, set
> > legal.realtek.license_ack=1 in /boot/loader.conf.
> > module_register_init: MOD_LOAD (urtwn_rtl8192cfwT_fw, ffffffff82b73fa0,
> > 0) error 1
> > urtwn-rtl8192cfwT: firmware image loaded, but did not register
> > urtwn0: failed loadfirmware of file urtwn-rtl8192cfwT
> > urtwn-rtl8192cfwT: could not load firmware image, error 17
> > urtwn0: failed loadfirmware of file urtwn-rtl8192cfwT
> > urtwn-rtl8192cfwT: could not load firmware image, error 17
> > urtwn0: failed loadfirmware of file urtwn-rtl8192cfwT
> > urtwn-rtl8192cfwT: could not load firmware image, error 17
> > urtwn0: failed loadfirmware of file urtwn-rtl8192cfwT
> > urtwn0: at uhub0, port 2, addr 4 (disconnected)
> > urtwn0: detached
> > urtwn0: <vendor 0x7392 product 0x7811, class 0/0, rev 2.00/2.00, addr 1>
> > on usbus0
> > urtwn0: MAC/BB RTL8188CUS, RF 6052 1T1R
> > urtwn0: enabling 11n
> > urtwn0: at uhub0, port 2, addr 1 (disconnected)
> > urtwn0: detached
> > urtwn0: <vendor 0x7392 product 0x7811, class 0/0, rev 2.00/2.00, addr 7>
> > on usbus0
> > urtwn0: MAC/BB RTL8188CUS, RF 6052 1T1R
> > urtwn0: enabling 11n
> > urtwn1: <vendor 0x0bda product 0x8176, class 0/0, rev 2.00/2.00, addr 8>
> > on usbus0
> > urtwn1: MAC/BB RTL8188CUS, RF 6052 1T1R
> > urtwn1: enabling 11n
> > urtwn1: at uhub0, port 1, addr 8 (disconnected)
> > urtwn1: detached
> > urtwn1: <vendor 0x0bda product 0x8176, class 0/0, rev 2.00/2.00, addr 9>
> > on usbus0
> > urtwn1: MAC/BB RTL8188CUS, RF 6052 1T1R
> > urtwn1: enabling 11n
> > urtwn0: at uhub1, port 3, addr 7 (disconnected)
> > urtwn0: detached
> > urtwn1: at uhub0, port 2, addr 9 (disconnected)
> > urtwn1: detached
> > urtwn0: <vendor 0x0bda product 0x8176, class 0/0, rev 2.00/2.00, addr
> > 10> on usbus0
> > urtwn0: MAC/BB RTL8188CUS, RF 6052 1T1R
> > urtwn0: enabling 11n
> > urtwn0: at uhub1, port 3, addr 10 (disconnected)
> > urtwn0: detached
> > urtwn0: <vendor 0x7392 product 0x7811, class 0/0, rev 2.00/2.00, addr
> > 11> on usbus0
> > urtwn0: MAC/BB RTL8188CUS, RF 6052 1T1R
> > urtwn0: enabling 11n
> > urtwn0: at uhub1, port 3, addr 11 (disconnected)
> > urtwn0: detached
> > urtwn0: <vendor 0x7392 product 0x7811, class 0/0, rev 2.00/2.00, addr 2>
> > on usbus0
> > urtwn0: MAC/BB
> > urtwn0: enabling 11n
> > urtwn0: at uhub1, port 3, addr 2 (disconnected)
> > urtwn0: detached
> > urtwn0: <vendor 0x7392 product 0x7811, class 0/0, rev 2.00/2.00, addr 5>
> > on usbus0
> > urtwn0: MAC/BB RTL8188CUS, RF 6052 1T1R
> > urtwn0: enabling 11n
> > urtwn0: at uhub0, port 2, addr 5 (disconnected)
> > urtwn0: detached
> > urtwn0: <vendor 0x7392 product 0x7811, class 0/0, rev 2.00/2.00, addr 1>
> > on usbus0
> > urtwn0: MAC/BB RTL8188CUS, RF 6052 1T1R
> > urtwn0: enabling 11n
> > urtwn0: at uhub0, port 2, addr 1 (disconnected)
> > urtwn0: detached
> > urtwn0: <vendor 0x7392 product 0x7811, class 0/0, rev 2.00/2.00, addr 1>
> > on usbus0
> > urtwn0: MAC/BB RTL8188CUS, RF 6052 1T1R
> > urtwn0: enabling 11n
> >
> > /boot/loader.conf
> >
> > vfs.root.mountfrom="hammer2:serno/50026B726B053990.s1d"
> > legal.realtek.license_ack=1
> > if_urtwn_load="YES"
> > urtwn-rtl8192cfwT_load="YES"
> > urtwn-rtl8192cfwU_load="YES"
> > urtwn-rtl8188eufw_load="YES"
> >
> > --
> > “90% of my problems are due to ignorance, the other 10% is because I just don’t know any better.”
> >


More information about the Users mailing list