[WiFi] Intel Centrino Advanced 6235 (error 45)

Tobias Heilig 0x70b1 at web.de
Thu Oct 25 01:56:39 PDT 2018


further investigation:

what i figured out by myself so far is that the cause of this problem is an invalid
subdevice id i get for my wifi card (obviously).

one can check the corresponding code blocks in/if_iwn.c/  [1]:

> |515 sc->subdevice_id = pci_get_subdevice(dev); ... 534 error = 
> iwn_config_specific(sc, pci_get_device(dev)); 535 if (error != 0) { 
> 536 device_printf(dev, "could not attach device, error %d\n", 537 
> error); 538 goto fail; 539 } ...|

then, in/iwn_config_specific /function the error gets triggerd by the default case:

> |... 910 /* 6x35 Series */ 911 case IWN_DID_6035_1: 912 case 
> IWN_DID_6035_2: 913 switch(sc->subdevice_id) { 914 case 
> IWN_SDID_6035_1: 915 case IWN_SDID_6035_2: 916 case IWN_SDID_6035_3: 
> 917 case IWN_SDID_6035_4: 918 sc->fwname = "iwn6000g2bfw"; 919 
> sc->limits = &iwn6235_sensitivity_limits; 920 sc->base_params = 
> &iwn_6235_base_params; 921 break; 922 default: 923 
> device_printf(sc->sc_dev, "adapter type id : 0x%04x sub id:" 924 
> "0x%04x rev %d not supported (subdevice)\n", pid, 925 
> sc->subdevice_id,sc->hw_type); 926 return ENOTSUP; 927 } 928 break; ...|

so, the device id i get (0x088f -> IWN_DID_6035_2) is correct, but
the subdevice id (0x5260) is neither of the defined ones in if_iwn_devid.h [3]:

> 163 * Device ID for 6035 Series 164 * 
> -------------------------------------------------------------------------- 
> 165 */ 166 #define IWN_DID_6035_1 0x088E 167 #define IWN_DID_6035_2 
> 0x088F 168 /* SubDevice ID */ 169 #define IWN_SDID_6035_1 0x4060 170 
> #define IWN_SDID_6035_2 0x4260 171 #define IWN_SDID_6035_3 0x4460 172 
> #define IWN_SDID_6035_4 0x4860

so, where to go from here? what can i do? any suggestions to fix this annoying problem?


> i'm trying to boot dfly off my thinkpad t431s and obviously my wifi card is
> causing some problem:
>
> |
>> |iwn0.pci3.pcib2.pci0.pcib0.acpi0.nexus0.root0 iwn0: <Intel Centrino 
>> Advanced 6235> [tentative] mem 0xf0c00000-0xf0c01fff irq 1 7 at 
>> device 0.0 on pci3 iwn0: Reserved 0x2000 bytes for rid 0x10 type 3 at 
>> 0xf0c00000 iwn0: attempting to allocate 1 MSI vector (1 supported) 
>> alloc MSI intr 16 on cpu3 iwn0: using IRQ 16 on cpu3 for MSI *iwn0: 
>> adapter type id : 0x088f **sub id :0x5260 rev 11 not supported 
>> (subdevice)* iwn0: could not attach device, error 45 panic: MSI rid 1 
>> is not setup cpuid = 0 Trace beginning at frame 0xffffffff819718e0 
>> panic() at panic+0x236 0xffffffff805f8666 panic() at panic+0x236 
>> 0xffffffff805f8666 pci_teardown_intr() at pci_teardown_intr+0x2a1 
>> 0xffffffff8085c601 iwn_detach() at iwn_detach+0xb9 0xffffffff804fbf89 
>> iwn_attach() at iwn_attach+0x7cb 0xffffffff804fc85b device_doattach() 
>> at device_doattach+0x45 0xffffffff80622555 Debugger("panic") CPU0 
>> stopping CPUs: 0x0000000e stopped Stopped at Debugger+0x7c: movb 
>> $0,0xe67a49(%rip)|
> |
> |after physically removing the wifi card and trying again it booted 
> without issues. |Also, i checked/sys/dev/netif/iwn/if_iwn.c 
> <https://gitweb.dragonflybsd.org/dragonfly.git/blob/HEAD:/sys/dev/netif/iwn/if_iwn.c>  [1] and from what i can tell my wifi card is
> listed there and/sys/dev/netif/iwn/fw/iwn60002g/Makefile  <https://gitweb.dragonflybsd.org/dragonfly.git/blob/HEAD:/sys/dev/netif/iwn/fw/iwn6000g2b/Makefile>  [2] contains the correct Firmware
> for it.
>
>
> [1]https://gitweb.dragonflybsd.org/dragonfly.git/blob/HEAD:/sys/dev/netif/iwn/if_iwn.c
> [2]https://gitweb.dragonflybsd.org/dragonfly.git/blob/HEAD:/sys/dev/netif/iwn/fw/iwn6000g2b/Makef

[3] https://gitweb.dragonflybsd.org/dragonfly.git/blob/HEAD:/sys/dev/netif/iwn/if_iwn_devid.h

-- 
best regards,

Tobi

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.dragonflybsd.org/pipermail/users/attachments/20181025/e92d8046/attachment-0001.htm>


More information about the Users mailing list