AsRock Vision3D 137D, NVidia GeForce 425 (X server conf)

George g.lister at nodeunit.com
Mon Mar 9 02:59:41 PDT 2015


Hi guys,

I have the following question. I have an AsRock Vision 3D 137D HTPC with 
i3 core and an NVidia GeForce 425 card.

I wish to use the system for a personal desktop and some development 
etc.., the personal desktop is kind of a high priority for this system 
for me.

I have managed to get a sort of decent, screen uses 1600x1200 instead of 
the 1920x1080 optimal fonts are streched etc. (I am running XFCE), 
config for X see below:

# cat /etc/X11/xorg.conf
Section "ServerLayout"
     Identifier     "X.org Configured"
     Screen      0  "Screen0" 0 0
     InputDevice    "Mouse0" "CorePointer"
     InputDevice    "Keyboard0" "CoreKeyboard"
EndSection

Section "Files"
     ModulePath   "/usr/local/lib/xorg/modules"
     FontPath     "/usr/local/lib/X11/fonts/misc/"
     FontPath     "/usr/local/lib/X11/fonts/TTF/"
     FontPath     "/usr/local/lib/X11/fonts/OTF/"
     FontPath     "/usr/local/lib/X11/fonts/Type1/"
     FontPath     "/usr/local/lib/X11/fonts/100dpi/"
     FontPath     "/usr/local/lib/X11/fonts/75dpi/"
EndSection

Section "Module"
     Load  "glx"
EndSection

Section "InputDevice"
     Identifier  "Keyboard0"
     Driver      "kbd"
EndSection

Section "InputDevice"
     Identifier  "Mouse0"
     Driver      "mouse"
     Option      "Protocol" "auto"
     Option      "Device" "/dev/sysmouse"
     Option      "ZAxisMapping" "4 5 6 7"
EndSection

Section "Monitor"
     Identifier   "Monitor0"
     VendorName   "Samsung"
     ModelName    "BX2235 23inch LCD"
     HorizSync    31.469-79.976
     VertRefresh  56.250-75.029
         Modeline     "1152x864_75.00"  104.00  1152 1224 1344 1536 864 
867 871 905 -hsync +vsync
         Modeline     "1280x800_59.81"   83.25  1280 1352 1480 1680 800 
803 809 831 -hsync +vsync
         Modeline     "1280x800_74.93"  106.25  1280 1360 1488 1696 800 
803 809 838 -hsync +vsync
         Modeline     "1280x1024_60.02"  109.00  1280 1368 1496 1712 
1024 1027 1034 1063 -hsync +vsync
         Modeline     "1280x1024_75.03"  138.75  1280 1368 1504 1728 
1024 1027 1034 1072 -hsync +vsync
     Modeline     "1440x900_59.89"  106.25  1440 1528 1672 1904  900 903 
909 934 -hsync +vsync
         Modeline     "1440x900_74.98"  136.50  1440 1536 1688 1936 900 
903 909 942 -hsync +vsync
     Modeline     "1680x1200_60.00"  168.25  1680 1792 1968 2256 1200 
1203 1213 1245 -hsync +vsync
     Modeline     "1680x1050_59.95"  146.00  1680 1784 1960 2240 1050 
1053 1059 1089 -hsync +vsync
     Modeline     "1920x1080_60.00"  173.00  1920 2048 2248 2576 1080 
1083 1088 1120 -hsync +vsync
EndSection

Section "Device"
         ### Available Driver options are:-
         ### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
         ### <string>: "String", <freq>: "<f> Hz/kHz/MHz",
         ### <percent>: "<f>%"
         ### [arg]: arg optional
         #Option     "ShadowFB"              # [<bool>]
         #Option     "DefaultRefresh"        # [<bool>]
         #Option     "ModeSetClearScreen"    # [<bool>]
     Identifier  "Card0"
     Driver      "vesa"
     BusID       "PCI:1:0:0"
EndSection

Section "Screen"
     Identifier "Screen0"
     Device     "Card0"
     Monitor    "Monitor0"
     SubSection "Display"
         Viewport   0 0
         Depth     1
         Modes     "1152x864_75.00" "1280x800_59.81" "1280x800_74.93" 
"1280x1024_60.02" "1280x1024_75.03" "1440x900_59.89" "1440x900_74.98" 
"1680x1200_60.00" "1680x1050_59.95" "1920x1080_60.00"
     EndSubSection
     SubSection "Display"
         Viewport   0 0
         Depth     4
         Modes     "1152x864_75.00" "1280x800_59.81" "1280x800_74.93" 
"1280x1024_60.02" "1280x1024_75.03" "1440x900_59.89" "1440x900_74.98" 
"1680x1200_60.00" "1680x1050_59.95" "1920x1080_60.00"
     EndSubSection
     SubSection "Display"
         Viewport   0 0
         Depth     8
         Modes     "1152x864_75.00" "1280x800_59.81" "1280x800_74.93" 
"1280x1024_60.02" "1280x1024_75.03" "1440x900_59.89" "1440x900_74.98" 
"1680x1200_60.00" "1680x1050_59.95" "1920x1080_60.00"
     EndSubSection
     SubSection "Display"
         Viewport   0 0
         Depth     15
         Modes     "1152x864_75.00" "1280x800_59.81" "1280x800_74.93" 
"1280x1024_60.02" "1280x1024_75.03" "1440x900_59.89" "1440x900_74.98" 
"1680x1200_60.00" "1680x1050_59.95" "1920x1080_60.00"
     EndSubSection
     SubSection "Display"
         Viewport   0 0
         Depth     16
         Modes     "1152x864_75.00" "1280x800_59.81" "1280x800_74.93" 
"1280x1024_60.02" "1280x1024_75.03" "1440x900_59.89" "1440x900_74.98" 
"1680x1200_60.00" "1680x1050_59.95" "1920x1080_60.00"
     EndSubSection
     SubSection "Display"
         Viewport   0 0
         Depth     24
         Modes     "1152x864_75.00" "1280x800_59.81" "1280x800_74.93" 
"1280x1024_60.02" "1280x1024_75.03" "1440x900_59.89" "1440x900_74.98" 
"1680x1200_60.00" "1680x1050_59.95" "1920x1080_60.00"
     EndSubSection
EndSection

I tried also the "nv" NVidia??? driver but I get back "GeForce 425 not 
supported" the other drivers are ATI etc.. which will ot work.

I have tried PC-BSD 10.1 release on the machine and it has an NVidia 
driver which detects the card and everything looks OK on the screen. 
DragonFly is a FreeBSD derivative just like PC-BSD. I am wondering 
whether the driver has not been ported yet?? I have used PC-BSD and it 
is very nice but it is kind of too slow (compared to Ubuntu on the same 
machine) and I am having some issues accessing an NetBSD NFS server it 
hangs with timeouts on lockd ... anyway long story short. I decided to 
give DragonFly a try and it is smocking fast to boot to shutdown to 
install packages etc. ... if I could only get X setup it would be great. 
Then I can move on to fighting HP printing etc. ;).

Here is a dmesg from the machine:

$ dmesg
Copyright (c) 2003-2014 The DragonFly Project.
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
     The Regents of the University of California. All rights reserved.
DragonFly v4.0.3-RELEASE #27: Thu Jan 22 17:19:56 PST 2015
root at pkgbox64.dragonflybsd.org:/usr/obj/build/home/justin/src/sys/X86_64_GENERIC
TSC invariant clock: 2409543436 Hz, i8254 clock: 1193223 Hz
CPU: Intel(R) Core(TM) i3 CPU       M 370  @ 2.40GHz (2409.47-MHz 
K8-class CPU)
   Origin = "GenuineIntel"  Id = 0x20655  Stepping = 5
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Features2=0x9ae3bd<SSE3,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,POPCNT>
   AMD Features=0x28100800<SYSCALL,NX,RDTSCP,LM>
   AMD Features2=0x1<LAHF>
   Thermal and PM Features=0x5<SENSOR,ARAT>
   MONITOR/MWAIT Features=0x3<CST,INTBRK>
real memory  = 6433078272 (6135 MB)
avail memory = 6023581696 (5744 MB)
lapic: divisor index 0, frequency 66929700 Hz
Initialize MI interrupts
TSC testing MP synchronization ...
TSC is MP synchronized
TSC: cputimer freq 75296071, shift 5
FQ scheduler policy version 1.1 loaded
wdog: In-kernel automatic watchdog reset enabled
kbd1 at kbdmux0
disk scheduler: set policy of vn0 to noop
disk scheduler: set policy of vn1 to noop
disk scheduler: set policy of vn2 to noop
disk scheduler: set policy of vn3 to noop
disk scheduler: set policy of md0 to noop
md0: Malloc disk
ACPI: RSDP 0x00000000000F9EF0 000014 (v00 ACPIAM)
ACPI: RSDT 0x00000000D3770000 000044 (v01 102410 RSDT1223 20101024 MSFT 
00000097)
ACPI: FACP 0x00000000D3770200 000084 (v01 A_M_I  OEMFACP  12000601 MSFT 
00000097)
ACPI: DSDT 0x00000000D3770460 0074A4 (v01 AS388  AS388115 00000115 INTL 
20051117)
ACPI: FACS 0x00000000D3780000 000040
ACPI: APIC 0x00000000D3770390 00008C (v01 102410 APIC1223 20101024 MSFT 
00000097)
ACPI: MCFG 0x00000000D3770420 00003C (v01 102410 OEMMCFG  20101024 MSFT 
00000097)
ACPI: OEMB 0x00000000D3780040 000072 (v01 102410 OEMB1223 20101024 MSFT 
00000097)
ACPI: AAFT 0x00000000D377A460 000027 (v01 102410 OEMAAFT  20101024 MSFT 
00000097)
ACPI: HPET 0x00000000D377A490 000038 (v01 102410 OEMHPET  20101024 MSFT 
00000097)
ACPI: ASF! 0x00000000D377A4D0 000099 (v32 LEGEND I865PASF 00000001 INTL 
20051117)
ACPI: SSDT 0x00000000D37815F0 000363 (v01 DpgPmm CpuPm    00000012 INTL 
20051117)
cryptosoft0: <software crypto> on motherboard
aesni0: No AESNI support.
padlock0: No ACE support.
rdrand0: No RdRand support.
acpi0: <102410 RSDT1223> on motherboard
ACPI: All ACPI Tables successfully acquired
ACPI FADT: SCI testing interrupt mode ...
ACPI FADT: SCI select level/high
ACPI: Executed 1 blocks of module-level executable AML code
objcache_reclaimlist
objcache_reclaimlist
objcache_reclaimlist
objcache_reclaimlist
acpi0: Power Button (fixed)
Warning: ACPI is disabling APM's device.  You can't run both
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on 
acpi0
acpi_hpet0: frequency 14318180
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> irq 16 at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pcib1: No _PRT found, routing with pci
pcib1: No _PRT found, routing with pci
vgapci0: <VGA-compatible display> port 0xdc00-0xdc7f mem 
0xd6000000-0xd7ffffff,0xd8000000-0xdfffffff,0xfa000000-0xfaffffff irq 16 
at device 0.0 on pci1
vgapci0: Boot video device
pci1: <multimedia, HDA> (vendor 0x10de, dev 0x0bea) at device 0.1 irq 17
pci0: <dasp> (vendor 0x8086, dev 0x0050) at device 4.0 irq 16
ehci0: <Intel PCH USB 2.0 controller USB-B> mem 0xf9ff8000-0xf9ff83ff 
irq 16 at device 26.0 on pci0
usbus0: EHCI version 1.0
usbus0: <Intel PCH USB 2.0 controller USB-B> on ehci0
pci0: <multimedia, HDA> (vendor 0x8086, dev 0x3b56) at device 27.0 irq 22
pcib2: <ACPI PCI-PCI bridge> irq 17 at device 28.0 on pci0
pci2: <ACPI PCI bus> on pcib2
re0: <RealTek 8111/8168 PCIe Gigabit Ethernet> port 0xe800-0xe8ff mem 
0xf8ff8000-0xf8ffbfff,0xf8fff000-0xf8ffffff irq 16 at device 0.0 on pci2
re0: Hardware rev. 0x2c000000; PCI-E 125MHz
miibus0: <MII bus> on re0
rgephy0: <8211B/RTL8169S/8110S media interface> on miibus0
rgephy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
usbus0: 480Mbps High Speed USB v2.0
re0: MAC address: e0:69:95:1f:6d:81
pcib3: <ACPI PCI-PCI bridge> irq 16 at device 28.1 on pci0
pci3: <ACPI PCI bus> on pcib3
xhci0: <NEC uPD720200 USB 3.0 controller> mem 0xfbdfe000-0xfbdfffff irq 
17 at device 0.0 on pci3
ugen0.1: <Intel> at usbus0
uhub0: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0
xhci0: 32 byte context size.
usbus1 on xhci0
pcib4: <ACPI PCI-PCI bridge> irq 18 at device 28.2 on pci0
pci4: <ACPI PCI bus> on pcib4
ath0: <Atheros 9287> mem 0xfbef0000-0xfbefffff irq 18 at device 0.0 on pci4
usbus1: 5.0Gbps Super Speed USB v3.0
ugen1.1: <0x1033> at usbus1
uhub1: <0x1033 XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus1
ath0: AR9287 mac 384.2 RF5133 phy 15.15
ath0: 2GHz radio: 0x0000; 5GHz radio: 0x00c0
pcib5: <ACPI PCI-PCI bridge> irq 19 at device 28.3 on pci0
pci5: <ACPI PCI bus> on pcib5
xhci1: <XHCI (generic) USB 3.0 controller> mem 0xfbff0000-0xfbffffff irq 
19 at device 0.0 on pci5
xhci1: 32 byte context size.
usbus2 on xhci1
usbus2: 5.0Gbps Super Speed USB v3.0
ehci1: <Intel PCH USB 2.0 controller USB-A> mem 0xf9ff2000-0xf9ff23ff 
irq 23 at device 29.0 on pci0
usbus3: EHCI version 1.0
ugen2.1: <0x1b73> at usbus2
uhub2: <0x1b73 XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus2
usbus3: <Intel PCH USB 2.0 controller USB-A> on ehci1
usbus3: 480Mbps High Speed USB v2.0
pcib6: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci6: <ACPI PCI bus> on pcib6
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ATA controller> port 
0xc080-0xc08f,0xc400-0xc40f,0xc480-0xc483,0xc800-0xc807,0xc880-0xc883,0xcc00-0xcc07 
irq 19 at device 31.2 on pci0
ata2: <ATA channel 0> on atapci0
ugen3.1: <Intel> at usbus3
uhub3: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus3
disk scheduler: set policy of ad4 to noop
ad4: 953869MB <TOSHIBA MQ01ABD100 AX001A> at ata2-master UDMA33
ata3: <ATA channel 1> on atapci0
uhub2: 2 ports with 2 removable, self powered
pci0: <serial bus, SMBus> (vendor 0x8086, dev 0x3b30) at device 31.3 irq 18
atapci1: <Intel ATA controller> port 
0xb080-0xb08f,0xb400-0xb40f,0xb480-0xb483,0xb800-0xb807,0xb880-0xb883,0xbc00-0xbc07 
irq 19 at device 31.5 on pci0
ata4: <ATA channel 0> on atapci1
uhub1: 4 ports with 4 removable, self powered
unknown: timeout waiting for read DRQ
unknown: timeout waiting for read DRQ
disk scheduler: set policy of acd0 to noop
acd0: DVDR <Slimtype DVD A DL8ATS/XAB2> at ata4-master UDMA33
ata5: <ATA channel 1> on atapci1
uhub3: 8 ports with 8 removable, self powered
acpi_button0: <Power Button> on acpi0
cpu0: <ACPI CPU> on acpi0
ACPI: Dynamic OEM Table Load:
ACPI: SSDT 0xFFFFFFE03FACB600 001028 (v01 DpgPmm P001Ist  00000011 INTL 
20051117)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT 0xFFFFFFE0B6167380 0004F4 (v01 PmRef  P001Cst  00003001 INTL 
20051117)
cpu_cst0: <ACPI CPU C-State> on cpu0
cpu_pst0: <ACPI CPU P-State> on cpu0
clockmod0: <CPU clock modulation> on cpu0
coretemp0: <CPU On-Die Thermal Sensors> on cpu0
cpu1: <ACPI CPU> on acpi0
cpu_cst1: <ACPI CPU C-State> on cpu1
cpu_pst1: <ACPI CPU P-State> on cpu1
clockmod1: <CPU clock modulation> on cpu1
coretemp1: <CPU On-Die Thermal Sensors> on cpu1
cpu2: <ACPI CPU> on acpi0
cpu_cst2: <ACPI CPU C-State> on cpu2
cpu_pst2: <ACPI CPU P-State> on cpu2
clockmod2: <CPU clock modulation> on cpu2
coretemp2: <CPU On-Die Thermal Sensors> on cpu2
cpu3: <ACPI CPU> on acpi0
cpu_cst3: <ACPI CPU C-State> on cpu3
cpu_pst3: <ACPI CPU P-State> on cpu3
clockmod3: <CPU clock modulation> on cpu3
coretemp3: <CPU On-Die Thermal Sensors> on cpu3
ACPI: Enabled 4 GPEs in block 00 to 3F
pmtimer0 on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
ugen3.2: <vendor 0x8087> at usbus3
uhub4: <vendor 0x8087 product 0x0020, class 9/0, rev 2.00/0.00, addr 2> 
on usbus3
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
lm0: <Winbond W83627DHG Hardware Monitor> at port 0x290-0x297 on isa0
sio0: can't drain, serial port might not exist, disabling
sio1: can't drain, serial port might not exist, disabling
ppc0: cannot reserve I/O port range
hpt27xx: no controller detected.
CAM: Configuring 4 busses
CAM: finished configuring all busses
disk scheduler: set policy of cd0 to noop
cd0 at ata2 bus 0 target 0 lun 0
cd0: <Slimtype DVD A  DL8ATS XAB2> Removable CD-ROM SCSI-0 device
cd0: 33.000MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not present 
- tray open
uhub4: 8 ports with 8 removable, self powered
intr 19 on cpu3 at 40001/40000 hz, livelocked limit engaged!
ugen3.3: <vendor 0x05e3> at usbus3
uhub5: <vendor 0x05e3 USB2.0 Hub, class 9/0, rev 2.00/77.64, addr 3> on 
usbus3
uhub0: 6 ports with 6 removable, self powered
uhub5: 4 ports with 4 removable, self powered
ugen0.2: <vendor 0x8087> at usbus0
uhub6: <vendor 0x8087 product 0x0020, class 9/0, rev 2.00/0.00, addr 2> 
on usbus0
ugen3.4: <vendor 0x05e3> at usbus3
uhub7: <vendor 0x05e3 USB2.0 Hub, class 9/0, rev 2.00/77.64, addr 4> on 
usbus3
uhub6: 6 ports with 6 removable, self powered
uhub7: 4 ports with 4 removable, self powered
ugen0.3: <Logitech> at usbus0
ukbd0: <Logitech USB Receiver, class 0/0, rev 2.00/12.01, addr 3> on usbus0
kbd2 at ukbd0
ums0: <Logitech USB Receiver, class 0/0, rev 2.00/12.01, addr 3> on usbus0
ums0: 16 buttons and [XYZT] coordinates ID=2
uhid0: <Logitech USB Receiver, class 0/0, rev 2.00/12.01, addr 3> on usbus0
ugen3.5: <vendor 0x05e3> at usbus3
uhub8: <vendor 0x05e3 USB2.0 Hub, class 9/0, rev 2.00/9.01, addr 5> on 
usbus3
uhub8: 4 ports with 4 removable, self powered
no B_DEVMAGIC (bootdev=0)
ugen3.6: <vendor 0x05e3> at usbus3
uhub9: <vendor 0x05e3 USB2.0 Hub, class 9/0, rev 2.00/9.01, addr 6> on 
usbus3
uhub9: 4 ports with 4 removable, self powered
ugen3.7: <HP> at usbus3
umass0: <HP Photosmart B110 series, class 0/0, rev 2.00/1.00, addr 7> on 
usbus3
disk scheduler: set policy of da8 to noop
da8 at umass-sim0 bus 0 target 0 lun 0
da8: <HP Photosmart B110 1.00> Removable Direct Access SCSI-5 device
da8: 40.000MB/s transfers
da8: Attempt to query device size failed: NOT READY, Medium not present
Mounting root from hammer:serno/23BBPJN0T.s1d
HAMMER(ROOT) recovery check seqno=00233441
HAMMER(ROOT) recovery range 300000000a56b9d8-300000000a56b9d8
HAMMER(ROOT) recovery nexto 300000000a56b9d8 endseqno=00233442
HAMMER(ROOT) mounted clean, no recovery needed
DMA space used: 12416k, remaining available: 16384k
Mounting devfs
ugen3.8: <vendor 0x05e3> at usbus3
uhub10: <vendor 0x05e3 USB Hub 2.0, class 9/0, rev 2.00/7.02, addr 8> on 
usbus3
uhub10: 4 ports with 4 removable, self powered
ugen3.9: <Prolific Technology Inc.> at usbus3
ugen3.10: <Prolific Technology Inc.> at usbus3
ugen3.11: <Logitech> at usbus3
ums1: <Logitech USB-PS2 Optical Mouse, class 0/0, rev 2.00/27.30, addr 
11> on usbus3
ums1: 8 buttons and [XYZT] coordinates ID=0
ugen3.12: <Darfon> at usbus3
ukbd1: <Darfon USB Combo Keyboard, class 0/0, rev 1.10/2.02, addr 12> on 
usbus3
kbd3 at ukbd1
uhid1: <Darfon USB Combo Keyboard, class 0/0, rev 1.10/2.02, addr 12> on 
usbus3
ulpt0: <HP Photosmart B110 series, class 0/0, rev 2.00/1.00, addr 7> on 
usbus3
ulpt0: using bi-directional mode
ucom init
uplcom0: <Prolific Technology Inc. USB-Serial Controller, class 0/0, rev 
1.10/3.00, addr 10> on usbus3
attach tty
malloc:
uplcom1: <Prolific Technology Inc. USB-Serial Controller, class 0/0, rev 
1.10/3.00, addr 9> on usbus3
attach tty
malloc:
ugen3.11: <Logitech> at usbus3 (disconnected)
ums1: at uhub4, port 4, addr 11 (disconnected)
ums1: detached
ugen3.12: <Darfon> at usbus3 (disconnected)
ukbd1: at uhub4, port 5, addr 12 (disconnected)
ukbd1: detached
uhid1: at uhub4, port 5, addr 12 (disconnected)
uhid1: detached

If someone can give me a pointer from what I have provided here that 
would be great.
Thank you for making DragonFly!
Cheers,
George




More information about the Users mailing list