DragonFly won't boot on qemu-kvm-1.0
Emil Mikulic
emikulic at gmail.com
Thu Oct 11 08:41:15 PDT 2012
On Fri, Oct 12, 2012 at 2:16 AM, Matthew Dillon
<dillon at apollo.backplane.com> wrote:
> If you boot the kernel verbose and record the entire dmesg output
> we can match those up to see if they are reasonable.
kernel text=0x7eb6e0 data=0xf6ce3+0x1b0e9b5 syms=[0x8+0xc8c88+0x8+0xa7d9b]
acpi.ko size 0x65aba0 at 0x2963000
ehci.ko size 0x40c10 at 0x2fbe000
SMAP type=01 base=0000000000000000 len=000000000009f400
SMAP type=02 base=000000000009f400 len=0000000000000c00
SMAP type=02 base=00000000000f0000 len=0000000000010000
SMAP type=01 base=0000000000100000 len=000000003fefd000
SMAP type=02 base=000000003fffd000 len=0000000000003000
SMAP type=02 base=00000000feffc000 len=0000000000004000
SMAP type=02 base=00000000fffc0000 len=0000000000040000
Copyright (c) 2003-2012 The DragonFly Project.
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
Slab ZoneSize set to 128KB
Leaving critical section, allowing interrupts
ACPI SDT: RSDP not in EBDA
ACPI SDT: RSDP in BIOS mem
ACPI FADT: SCI irq 9, conform/conform
DragonFly v3.3.0.2.g9b99c-DEVELOPMENT #0: Wed Oct 10 12:57:32 EST 2012
root@:/usr/obj/usr/src/sys/X86_64_GENERIC
Calibrating clock(s) ... TSC clock: 2527167651 Hz, i8254 clock: 1193203 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
CLK_USE_TSC_CALIBRATION not specified - using old calibration method
CPU: QEMU Virtual CPU version 1.0 (2527.16-MHz K8-class CPU)
Origin = "GenuineIntel" Id = 0x623 Stepping = 3
Features=0x783fbfd<FPU,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE,SSE2>
Features2=0x80002021<SSE3,VMX,CX16,VMM>
AMD Features=0x20100800<SYSCALL,NX,LM>
AMD Features2=0x1<LAHF>
real memory = 1073333248 (1023 MB)
Physical memory chunk(s):
0x00020000 - 0x0007ffff, 393216 bytes (96 pages)
0x00100000 - 0x001fffff, 1048576 bytes (256 pages)
0x03580000 - 0x3ffbffff, 1017380864 bytes (248384 pages)
avail memory = 953683968 (909 MB)
ACPI MADT: LAPIC address 0xfee00000, flags 0x1
ACPI MADT: BSP apic id 0
ACPI MADT: cpu id 0, apic id 0
lapic: divisor index 0, frequency 500005820 Hz
SMP: CPU0 apic_initialize():
lint0: 0x00000700 lint1: 0x00010400 TPR: 0x00000000 SVR: 0x000001ff
SMI Frequency (worst case): 7874 Hz (127 us)
SMP: Waiting APs LAPIC initialization
ELCR Found. ISA IRQs programmed as:
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
E E E E E E E E E E L L E E E E
MPTABLE: 0:1 INTA -> IOAPIC 0.9
MPTABLE: 0:3 INTA -> IOAPIC 0.11
Initialize MI interrupts
Finish MP startup
Active CPU Mask: 0000000000000001
ndepotmags=142 x mag_cap=128 for mbuf
ndepotmags=71 x mag_cap=128 for mbuf pkt hdr
ndepotmags=10 x mag_cap=128 for cluster mbuf
ndepotmags=10 x mag_cap=128 for jcluster mbuf
ndepotmags=10 x mag_cap=128 for mbuf + cluster
ndepotmags=4 x mag_cap=39 for mbuf pkt hdr + cluster
ndepotmags=10 x mag_cap=128 for mbuf + jcluster
ndepotmags=4 x mag_cap=39 for mbuf pkt hdr + jcluster
ndepotmags=4 x mag_cap=33 for sf_buf
ndepotmags=3 x mag_cap=4 for exec-args
Preloaded elf kernel "kernel" at 0xffffffff83000000.
Preloaded elf obj module "acpi.ko" at 0xffffffff83000230.
Preloaded elf obj module "ehci.ko" at 0xffffffff83000bc8.
BITS within APICID: logical_CPU_bits: 0; core_bits: 0
CPU Topology: cores_per_chip: 1; threads_per_core: 1; chips_per_package: 1;
Start scheduler helpers on cpus:
cpu0 - Unknown cpunode->type=1. Siblings: no siblings
start dummy scheduler helpers on cpus: 0
Start scheduler helpers on cpus:
cpu0 - Unknown cpunode->type=1. Siblings: no siblings
ndepotmags=4 x mag_cap=9 for thread
ndepotmags=4 x mag_cap=33 for dsched-tdio-cache
ndepotmags=4 x mag_cap=33 for dsched-tdctx-cache
ndepotmags=4 x mag_cap=33 for dsched-diskctx-cache
ndepotmags=4 x mag_cap=9 for vmspace
ndepotmags=4 x mag_cap=33 for devfs-node-cache
ndepotmags=4 x mag_cap=33 for devfs-msg-cache
ndepotmags=4 x mag_cap=33 for devfs-dev-cache
ndepotmags=4 x mag_cap=33 for disk-msg-cache
FQ scheduler policy version 1.1 loaded
ndepotmags=4 x mag_cap=33 for propdict
ndepotmags=4 x mag_cap=33 for propstng
ndepotmags=4 x mag_cap=33 for pdict128
ndepotmags=4 x mag_cap=33 for pdict32
ndepotmags=4 x mag_cap=33 for propdata
ndepotmags=4 x mag_cap=33 for pdict16
ndepotmags=4 x mag_cap=9 for devfs
wdog: In-kernel automatic watchdog reset enabled
ndepotmags=4 x mag_cap=33 for propnmbr
ndepotmags=4 x mag_cap=33 for proparay
wlan: <802.11 Link Layer>
ndepotmags=4 x mag_cap=33 for devfs-rule-cache
ndepotmags=4 x mag_cap=33 for ata_request
ndepotmags=4 x mag_cap=33 for ata_composite
kbd: new array size 4
kbd1 at kbdmux0
ndepotmags=4 x mag_cap=33 for crypto op
ndepotmags=4 x mag_cap=33 for crypto desc
crypto: <crypto core>
No policy for md0 specified, or policy not found
disk scheduler: set policy of md0 to noop
md0: Malloc disk
md0: invalid primary partition table: no magic
hpt27xx: RocketRAID 27xx controller driver v1.0 (Oct 10 2012 12:08:36)
hptrr: RocketRAID 17xx/2xxx SATA controller driver v1.2
ICU: rman cpu0 0 - 1
ICU: rman cpu0 3 - 95
ICU: rman cpu0 97 - 191
ACPI: RSDP 0xfd9a0 00014 (v0 BOCHS )
ACPI: RSDT 0x3fffd7b0 00034 (v1 BOCHS BXPCRSDT 00000001 BXPC 00000001)
ACPI: FACP 0x3fffff80 00074 (v1 BOCHS BXPCFACP 00000001 BXPC 00000001)
ACPI: DSDT 0x3fffd9b0 02589 (v1 BXPC BXDSDT 00000001 INTL 20100528)
ACPI: FACS 0x3fffff40 00040
ACPI: SSDT 0x3fffd910 0009E (v1 BOCHS BXPCSSDT 00000001 BXPC 00000001)
ACPI: APIC 0x3fffd830 00072 (v1 BOCHS BXPCAPIC 00000001 BXPC 00000001)
ACPI: HPET 0x3fffd7f0 00038 (v1 BOCHS BXPCHPET 00000001 BXPC 00000001)
cryptosoft0.nexus0.root0
cryptosoft0: <software crypto> [tentative] on motherboard
crypto: assign cryptosoft0 driver id 0, flags 234881024
crypto: cryptosoft0 registers alg 1 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 2 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 3 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 4 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 5 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 16 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 6 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 7 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 18 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 19 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 20 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 8 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 15 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 9 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 10 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 13 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 14 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 11 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 22 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 23 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 24 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 28 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 25 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 26 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 27 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 21 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 29 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 30 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 31 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 32 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 17 flags 0 maxoplen 0
cryptosoft0: <software crypto> [attached!] on motherboard
acpi0.nexus0.root0
acpi0: <BOCHS BXPCRSDT> [tentative] on motherboard
ndepotmags=4 x mag_cap=33 for Acpi-Namespace
ndepotmags=4 x mag_cap=33 for Acpi-State
ndepotmags=4 x mag_cap=33 for Acpi-Parse
ndepotmags=4 x mag_cap=33 for Acpi-ParseExt
ndepotmags=4 x mag_cap=33 for Acpi-Operand
ACPI FADT: SCI testing interrupt mode ...
ACPI FADT: SCI testing level/low
ICU: irq 9, edge -> level
ACPI FADT: SCI select level/low
objcache_reclaimlist
objcache_reclaimlist
objcache_reclaimlist
objcache_reclaimlist
acpi0: Power Button (fixed)
Warning: ACPI is disabling APM's device. You can't run both
ACPI timer looks BAD min = 23, max = 202, width = 179
ACPI timer looks BAD min = 24, max = 81, width = 57
ACPI timer looks BAD min = 24, max = 186, width = 162
ACPI timer looks BAD min = 24, max = 86, width = 62
ACPI timer looks BAD min = 24, max = 195, width = 171
ACPI timer looks BAD min = 24, max = 71, width = 47
ACPI timer looks BAD min = 23, max = 177, width = 154
ACPI timer looks BAD min = 24, max = 84, width = 60
ACPI timer looks BAD min = 23, max = 85, width = 62
ACPI timer looks BAD min = 23, max = 92, width = 69
acpi_timer0.acpi0.nexus0.root0
acpi_timer0: <24-bit timer at 3.579545MHz> [tentative] port
0xb008-0xb00b on acpi0
acpi_timer0: <24-bit timer at 3.579545MHz> [attached!] port
0xb008-0xb00b on acpi0
acpi_hpet0.acpi0.nexus0.root0
acpi_hpet0: <High Precision Event Timer> [tentative] iomem
0xfed00000-0xfed003ff on acpi0
acpi_hpet0: vend: 0x8086, rev: 0x1, num: 2, opts: legacy_route 64-bit
acpi_hpet0: frequency 100000000
acpi_hpet0: <High Precision Event Timer> [attached!] iomem
0xfed00000-0xfed003ff on acpi0
pci_link0: Index IRQ Rtd Ref IRQs
Initial Probe 0 10 N 0 5 10 11
Validation 0 10 N 0 5 10 11
After Disable 0 255 N 0 5 10 11
pci_link1: Index IRQ Rtd Ref IRQs
Initial Probe 0 10 N 0 5 10 11
Validation 0 10 N 0 5 10 11
After Disable 0 255 N 0 5 10 11
pci_link2: Index IRQ Rtd Ref IRQs
Initial Probe 0 11 N 0 5 10 11
Validation 0 11 N 0 5 10 11
After Disable 0 255 N 0 5 10 11
pci_link3: Index IRQ Rtd Ref IRQs
Initial Probe 0 11 N 0 5 10 11
Validation 0 11 N 0 5 10 11
After Disable 0 255 N 0 5 10 11
pci_link4: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 9
Validation 0 255 N 0 9
After Disable 0 255 N 0 9
pcib0.acpi0.nexus0.root0
pcib0: <ACPI Host-PCI bridge> [tentative] port 0xcf8-0xcff on acpi0
ACPI: Found matching pin for 0.1.INTA at func 3: 9
ACPI: Found matching pin for 0.3.INTA at func 0: 11
pci0.pcib0.acpi0.nexus0.root0
pci0: <ACPI PCI bus> [tentative] on pcib0
pci0: domain=0, physical bus=0
found-> vendor=0x8086, dev=0x1237, revid=0x02
domain=0, bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0003, statreg=0x0000, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x7000, revid=0x00
domain=0, bus=0, slot=1, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x0003, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x7010, revid=0x00
domain=0, bus=0, slot=1, func=1
class=01-01-80, hdrtype=0x00, mfdev=0
cmdreg=0x0003, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[20]: type I/O Port, range 32, base 0xc100, size 4, enabled
found-> vendor=0x8086, dev=0x7113, revid=0x03
domain=0, bus=0, slot=1, func=3
class=06-80-00, hdrtype=0x00, mfdev=0
cmdreg=0x0003, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=9
pcib0: matched entry for 0.1.INTA (src \_SB_.LNKS:0)
pci_link4: Unable to route IRQs: AE_NOT_FOUND
found-> vendor=0x1013, dev=0x00b8, revid=0x00
domain=0, bus=0, slot=2, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0003, statreg=0x0000, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[10]: type Prefetchable Memory, range 32, base 0xfc000000, size 25, enabled
map[14]: type Memory, range 32, base 0xfebf0000, size 12, enabled
found-> vendor=0x10ec, dev=0x8139, revid=0x20
domain=0, bus=0, slot=3, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0003, statreg=0x0000, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
map[10]: type I/O Port, range 32, base 0xc000, size 8, enabled
map[14]: type Memory, range 32, base 0xfebf1000, size 8, enabled
pcib0: matched entry for 0.3.INTA (src \_SB_.LNKC:0)
pcib0: slot 3 INTA routed to irq 11 via \_SB_.LNKC
isab0.pci0.pcib0.acpi0.nexus0.root0
isab0: <PCI-ISA bridge> [tentative] at device 1.0 on pci0
isa0.isab0.pci0.pcib0.acpi0.nexus0.root0
isa0: <ISA bus> [tentative] on isab0
isa0: <ISA bus> [attached!] on isab0
isab0: <PCI-ISA bridge> [attached!] at device 1.0 on pci0
atapci0.pci0.pcib0.acpi0.nexus0.root0
atapci0: <Intel PIIX3 WDMA2 controller> [tentative] port
0xc100-0xc10f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 1.1 on
pci0
atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0xc100
ata0.atapci0.pci0.pcib0.acpi0.nexus0.root0
ata0: <ATA channel 0> [tentative] on atapci0
atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
ata0: reset tp1 mask=03 ostat0=50 ostat1=00
ata0: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata0: stat1=0x00 err=0x00 lsb=0xff msb=0xff
ata0: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata0-master: pio=PIO4 wdma=WDMA2 udma=UDMA100 cable=80 wire
atapicam-: atapicam0 exists, using next available unit number
ad1: setting PIO4 on PIIX3 chip
ad1: setting WDMA2 on PIIX3 chip
No policy for ad1 specified, or policy not found
disk scheduler: set policy of ad1 to noop
ad1: Intel check1 failed
ad1: Adaptec check1 failed
ad1: LSI (v3) check1 failed
ad1: LSI (v2) check1 failed
ad1: FreeBSD check1 failed
ad1: 61440MB <QEMU HARDDISK 1.0> at ata0-master WDMA2
ad1: 125829120 sectors [124830C/16H/63S] 16 sectors/interrupt 1 depth queue
ata0: <ATA channel 0> [attached!] on atapci0
ata1.atapci0.pci0.pcib0.acpi0.nexus0.root0
ata1: <ATA channel 1> [tentative] on atapci0
atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
ata1: reset tp1 mask=03 ostat0=50 ostat1=00
ata1: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb
ata1: stat1=0x00 err=0x00 lsb=0xff msb=0xff
ata1: reset tp2 stat0=00 stat1=00 devices=0x4<ATAPI_MASTER>
ata1-master: pio=PIO4 wdma=WDMA2 udma=UDMA100 cable=40 wire
ad1: type 0xa5, start 63, end = 125814527, size 125814465 : OK
acd0: setting PIO4 on PIIX3 chip
acd0: setting WDMA2 on PIIX3 chip
No policy for acd0 specified, or policy not found
disk scheduler: set policy of acd0 to noop
acd0: <QEMU DVD-ROM/1.0> DVDROM drive at ata1 as master
acd0: read 687KB/s (687KB/s), 512KB buffer, WDMA2
acd0: Reads: CDR, CDRW, DVDROM, DVDR, DVDRAM
acd0: Writes:
acd0: Audio: play, 2 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: no/blank disc
ata1: <ATA channel 1> [attached!] on atapci0
atapci0: <Intel PIIX3 WDMA2 controller> [attached!] port
0xc100-0xc10f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 1.1 on
pci0
pci0: <bridge> (vendor 0x8086, dev 0x7113) at device 1.3 irq 9
vgapci0.pci0.pcib0.acpi0.nexus0.root0
vgapci0: <VGA-compatible display> [tentative] mem
0xfebf0000-0xfebf0fff,0xfc000000-0xfdffffff at device 2.0 on pci0
vgapci0: <VGA-compatible display> [attached!] mem
0xfebf0000-0xfebf0fff,0xfc000000-0xfdffffff at device 2.0 on pci0
re0: Reserved 0x100 bytes for rid 0x10 type 4 at 0xc000
re0.pci0.pcib0.acpi0.nexus0.root0
re0: <RealTek 8139C+ 10/100BaseTX> [tentative] port 0xc000-0xc0ff mem
0xfebf1000-0xfebf10ff irq 11 at device 3.0 on pci0
re0: Hardware rev. 0x74800000; MAC ver. 0x00; PCI32 33MHz
miibus0.re0.pci0.pcib0.acpi0.nexus0.root0
miibus0: <MII bus> [tentative] on re0
ukphy0.miibus0.re0.pci0.pcib0.acpi0.nexus0.root0
ukphy0: <Generic IEEE 802.3u media interface> [tentative] on miibus0
ukphy0: OUI 0x000000, model 0x0000, rev. 0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
ukphy0: <Generic IEEE 802.3u media interface> [attached!] on miibus0
miibus0: <MII bus> [attached!] on re0
re0: bpf attached
re0: MAC address: 52:54:00:12:34:56
re0: <RealTek 8139C+ 10/100BaseTX> [attached!] port 0xc000-0xc0ff mem
0xfebf1000-0xfebf10ff irq 11 at device 3.0 on pci0
pci0: <ACPI PCI bus> [attached!] on pcib0
pcib0: <ACPI Host-PCI bridge> [attached!] port 0xcf8-0xcff on acpi0
atkbdc0.acpi0.nexus0.root0
atkbdc0: <Keyboard controller (i8042)> [tentative] port 0x64,0x60 irq 1 on acpi0
atkbd0.atkbdc0.acpi0.nexus0.root0
atkbd0: <AT Keyboard> [tentative] flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0061
atkbd: keyboard ID 0x41ab (2)
kbdc: RESET_KBD return code:00fa
kbdc: RESET_KBD status:00aa
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x1d0000
atkbd0: <AT Keyboard> [attached!] flags 0x1 irq 1 on atkbdc0
psm0: current command byte:0061
kbdc: TEST_AUX_PORT status:0000
kbdc: RESET_AUX return code:00fa
kbdc: RESET_AUX status:00aa
kbdc: RESET_AUX ID:0000
kbdc: RESET_AUX return code:00fa
kbdc: RESET_AUX status:00aa
kbdc: RESET_AUX ID:0000
psm: status 00 02 64
psm: status 00 00 64
psm: status 00 03 64
psm: status 00 03 64
psm: data 08 00 00
psm: status 00 02 64
psm0.atkbdc0.acpi0.nexus0.root0
psm0: <PS/2 Mouse> [tentative] irq 12 on atkbdc0
psm0: model IntelliMouse Explorer, device ID 4-00, 5 buttons
psm0: config:00000000, flags:00000008, packet size:4
psm0: syncmask:08, syncbits:00
psm0: <PS/2 Mouse> [attached!] irq 12 on atkbdc0
atkbdc0: <Keyboard controller (i8042)> [attached!] port 0x64,0x60 irq 1 on acpi0
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
cpu0.acpi0.nexus0.root0
cpu0: <ACPI CPU> [tentative] on acpi0
cpu0: _OSC failed, use _PDC
cpu_cst0.cpu0.acpi0.nexus0.root0
cpu_cst0: <ACPI CPU C-State> [tentative] on cpu0
cpu_cst0: switching to generic Cx mode
cpu_cst0: <ACPI CPU C-State> [attached!] on cpu0
cpu_pst0: Can't get _PCT package - AE_NOT_FOUND
cpu0: <ACPI CPU> [attached!] on acpi0
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
acpi0: <BOCHS BXPCRSDT> [attached!] at irq 9 on motherboard
atkbdc-: atkbdc0 exists, using next available unit number
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
ex_isa_identify()
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
pmtimer0.isa0.isab0.pci0.pcib0.acpi0.nexus0.root0
pmtimer0 [tentative] on isa0
pmtimer0 [attached!] on isa0
adv0 [tentative] failed to probe on isa0
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x330
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x334
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x230
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x234
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x130
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x134
bt0 [tentative] failed to probe at port 0x134-0x137 on isa0
atkbdc1: <Keyboard controller (i8042)> [tentative] failed to probe at
port 0x60 on isa0
vga0.isa0.isab0.pci0.pcib0.acpi0.nexus0.root0
vga0: <Generic ISA VGA> [tentative] at port 0x3c0-0x3df iomem
0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xffffffff800b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0e 0f 00 00 06 90 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 0f ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 0f ff
VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 0f ff
vga0: <Generic ISA VGA> [attached!] at port 0x3c0-0x3df iomem
0xa0000-0xbffff on isa0
sc0.isa0.isab0.pci0.pcib0.acpi0.nexus0.root0
sc0: <System console> [tentative] at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x100>
sc0: fb0, kbd1, terminal emulator: sc (syscons terminal)
sc0: <System console> [attached!] at flags 0x100 on isa0
lm0 [tentative] failed to probe at port 0x290-0x297 on isa0
it0 [tentative] failed to probe at port 0x290-0x297 on isa0
it1 [tentative] failed to probe at port 0xc00-0xc07 on isa0
it2 [tentative] failed to probe at port 0xd00-0xd07 on isa0
it3 [tentative] failed to probe at port 0x228-0x22f on isa0
wbsio0 [tentative] failed to probe at port 0x2e-0x2f on isa0
wbsio1 [tentative] failed to probe at port 0x4e-0x4f on isa0
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: irq maps: 0x13 0x13 0x13 0x13
sio0.isa0.isab0.pci0.pcib0.acpi0.nexus0.root0
sio0 [tentative] at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A, console
sio0 [attached!] at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio1: can't drain, serial port might not exist, disabling
sio1 [tentative] failed to probe at port 0x2f8-0x2ff irq 3 on isa0
sio2: not probed (disabled)
sio3: not probed (disabled)
ppc0: cannot reserve I/O port range
ppc0: <Parallel port> [tentative] failed to probe at irq 7 on isa0
ed0: not probed (disabled)
lnc0: not probed (disabled)
cs0: not probed (disabled)
sn0: not probed (disabled)
isa_probe_children: probing PnP devices
ndepotmags=4 x mag_cap=33 for nameibufs
ndepotmags=4 x mag_cap=33 for NFS mount
ndepotmags=4 x mag_cap=33 for NFS node
ndepotmags=4 x mag_cap=65 for vnodes
faith0: bpf attached
lo0: bpf attached
ppp0: bpf attached
sl0: bpf attached
ndepotmags=4 x mag_cap=33 for UFS dirhash
hpt27xx: no controller detected.
hptrr: no controller detected.
CAM: Configuring bus: ata0
CAM: Configuring bus: ata1
CAM: Configuring 2 busses
CAM: Finished configuring bus: ata0
(probe0:ata1:0:0:0): error 6
(probe0:ata1:0:0:0): Unretryable Error
CAM: Finished configuring bus: ata1
CAM: finished configuring all busses
pass0 at ata1 bus 0 target 0 lun 0
pass0: <QEMU QEMU DVD-ROM 1.0> Removable CD-ROM SCSI-0 device
pass0: 16.000MB/s transfers
sg0 at ata1 bus 0 target 0 lun 0
sg0: <QEMU QEMU DVD-ROM 1.0> Removable CD-ROM SCSI-0 device
sg0: 16.000MB/s transfers
No policy for cd0 specified, or policy not found
disk scheduler: set policy of cd0 to noop
(cd0:ata1:0:0:0): error 6
(cd0:ata1:0:0:0): Unretryable Error
cd0 at ata1 bus 0 target 0 lun 0
cd0: <QEMU QEMU DVD-ROM 1.0> Removable CD-ROM SCSI-0 device
cd0: 16.000MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not present
no B_DEVMAGIC (bootdev=0)
ATA PseudoRAID loaded
Mounting root from hammer:serno/QM00001.s1d
HAMMER(ROOT) recovery check seqno=00442467
HAMMER(ROOT) recovery range 3000000003848338-3000000003848338
HAMMER(ROOT) recovery nexto 3000000003848338 endseqno=00442468
HAMMER(ROOT) mounted clean, no recovery needed
DMA space used: 144k, remaining available: 16384k
Fatal trap 9: general protection fault while in kernel mode
cpuid = 0; lapic->id = 00000000
instruction pointer = 0x8:0xffffffff80898a02
stack pointer = 0x10:0xffffffe00e457c00
frame pointer = 0x10:0xffffffe003218bb0
code segment = base 0x0, limit 0xfffff, type 0x1b
= DPL 0, pres 1, long 0, def32 0, gran 1
processor eflags = interrupt enabled, IOPL = 0
current process = 1
current thread = pri 10 (CRIT)
kernel: type 9 trap, code=0
CPU0 stopping CPUs: 0x00000000
stopped
Stopped at cpu_heavy_restore+0x72: movl %ecx,%cr3
db>
More information about the Users
mailing list