Unable to login with PPPoE (2.10-RELEASE x86)

Georg Bege therion at ninth-art.de
Wed Jul 6 19:52:19 PDT 2011 

Good day to you all

I recently installed Dragonfly BSD on some box of mine -
potentially replacing my old router.
Im not really a beginner, did use various BSDs before but
using FreeBSD most of the time.

I actually never had a lot of issue regarding this, but now Im running
out of ideas.

Whatever I try Im not able to use PPPoE to login to my internet (which
is essential for the purpose of this box).
I seem to get an IP but I cannot ping anything (eg. no routing?)

I'll attach my ppp.conf and a ppp.log (for the logging options I used,
see the conf.)
Of course my auth is correct, else I wouldnt get an IP actually.
I compile my own kernel now, but for now I keep running the generic
stuff:

-----------------------snip-----------------------------
re0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
        options=1b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING>
        inet6 fe80::beae:c5ff:feb7:a940%re0 prefixlen 64 scopeid 0x1 
        ether bc:ae:c5:b7:a9:40
        media: Ethernet autoselect (100baseTX <full-duplex>)
        status: active
ath0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 2290
        ether d8:5d:4c:ba:d4:7a
        media: IEEE 802.11 Wireless Ethernet autoselect mode 11g
<hostap>
        status: associated
lp0: flags=8810<POINTOPOINT,SIMPLEX,MULTICAST> mtu 1500
faith0: flags=8002<BROADCAST,MULTICAST> mtu 1500
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
        options=3<RXCSUM,TXCSUM>
        inet 127.0.0.1 netmask 0xff000000 
        inet6 ::1 prefixlen 128 
        inet6 fe80::1%lo0 prefixlen 64 scopeid 0x5 
ppp0: flags=8010<POINTOPOINT,MULTICAST> mtu 1500
sl0: flags=c010<POINTOPOINT,LINK2,MULTICAST> mtu 552
wlan0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
        inet 192.168.2.1 netmask 0xfffffff8 broadcast 192.168.2.7
        inet6 fe80::da5d:4cff:feba:d47a%wlan0 prefixlen 64 scopeid 0x8 
        ether d8:5d:4c:ba:d4:7a
        media: IEEE 802.11 Wireless Ethernet autoselect mode 11g
<hostap>
        status: associated
        ssid ninth-art.net channel 7 (2442 MHz 11g) bssid
d8:5d:4c:ba:d4:7a
        regdomain ETSI country DE indoor ecm authmode WPA privacy MIXED
        deftxkey 2 TKIP 2:128-bit TKIP 3:128-bit txpower 30 scanvalid 60
        protmode CTS wme burst dtimperiod 1 -dfs
tun0: flags=8010<POINTOPOINT,MULTICAST> mtu 1492
-----------------------snip-----------------------------
(as you can see I've setup my wireless card already)

uname -a:
-----------------------snip-----------------------------
DragonFly aquina.ninth-art.net 2.10-RELEASE DragonFly
v2.10.1.1.gf7ba0-RELEASE #1: Mon Apr 25 19:48:10 UTC 2011
root at pkgbox32.dragonflybsd.org:/usr/obj/usr/src/sys/GENERIC  i386
-----------------------snip-----------------------------

kldstat:
-----------------------snip-----------------------------
Id Refs Address    Size     Name
 1   21 0xc0100000 83ac14   kernel
 2    1 0xc093b000 1680c    if_ath.ko
 3    3 0xc0952000 62aec    ath_hal.ko
 4    2 0xc09b5000 4b44     ath_rate.ko
 5    1 0xc09ba000 7754c    acpi.ko
 6    1 0xc0a32000 133c4    ahci.ko
 7    1 0xc0a46000 9708     ehci.ko
 8    2 0xc0a50000 b8a0     dm.ko
 9    1 0xc0a5c000 18d80    dm_target_crypt.ko
10    1 0xc1975000 1ca0     wlan_xauth.ko
11    1 0xd2b40000 9000     netgraph.ko
12    1 0xd2b0e000 4000     ng_ksocket.ko
13    1 0xd2b12000 3000     ng_ether.ko
14    1 0xd2b49000 4000     ng_pppoe.ko
15    1 0xd2b4d000 3000     ng_socket.ko
-----------------------snip-----------------------------

PS.:
Another issue of mine (which might be minor) is that whether Im loading
pf.ko or not I dont get the /dev/pf actually.

cheers
-- 
Georg Bege <therion at ninth-art.de>


!DSPAM:4e151e44844721308043045!
Jul  7 04:24:04 aquina ppp[337]: tun0: Phase: Received NGM_PPPOE_ACNAME (hook "duibr1")
Jul  7 04:24:04 aquina ppp[337]: tun0: Phase: Received NGM_PPPOE_SESSIONID
Jul  7 04:24:04 aquina ppp[337]: tun0: Phase: Received NGM_PPPOE_SUCCESS
Jul  7 04:24:04 aquina ppp[337]: tun0: Phase: deflink: carrier -> login
Jul  7 04:24:04 aquina ppp[337]: tun0: Phase: deflink: login -> lcp
Jul  7 04:24:04 aquina ppp[337]: tun0: LCP: FSM: Using "deflink" as a transport
Jul  7 04:24:04 aquina ppp[337]: tun0: LCP: deflink: State change Initial --> Closed
Jul  7 04:24:04 aquina ppp[337]: tun0: LCP: deflink: State change Closed --> Stopped
Jul  7 04:24:05 aquina ppp[337]: tun0: LCP: deflink: LayerStart
Jul  7 04:24:05 aquina ppp[337]: tun0: LCP: deflink: SendConfigReq(1) state = Stopped
Jul  7 04:24:05 aquina ppp[337]: tun0: LCP:  ACFCOMP[2]
Jul  7 04:24:05 aquina ppp[337]: tun0: LCP:  PROTOCOMP[2]
Jul  7 04:24:05 aquina ppp[337]: tun0: LCP:  ACCMAP[6] 0x00000000
Jul  7 04:24:05 aquina ppp[337]: tun0: LCP:  MRU[4] 1492
Jul  7 04:24:05 aquina ppp[337]: tun0: LCP:  MAGICNUM[6] 0x526c492e
Jul  7 04:24:05 aquina ppp[337]: tun0: LCP:  QUALPROTO[8] proto c025, interval 30000ms
Jul  7 04:24:05 aquina ppp[337]: tun0: LCP: deflink: State change Stopped --> Req-Sent
Jul  7 04:24:05 aquina ppp[337]: tun0: LCP: deflink: RecvConfigReq(4) state = Req-Sent
Jul  7 04:24:05 aquina ppp[337]: tun0: LCP:  MRU[4] 1492
Jul  7 04:24:05 aquina ppp[337]: tun0: LCP:  AUTHPROTO[5] 0xc223 (CHAP 0x05)
Jul  7 04:24:05 aquina ppp[337]: tun0: LCP:  MAGICNUM[6] 0x5c512db9
Jul  7 04:24:05 aquina ppp[337]: tun0: LCP: deflink: SendConfigAck(4) state = Req-Sent
Jul  7 04:24:05 aquina ppp[337]: tun0: LCP:  MRU[4] 1492
Jul  7 04:24:05 aquina ppp[337]: tun0: LCP:  AUTHPROTO[5] 0xc223 (CHAP 0x05)
Jul  7 04:24:05 aquina ppp[337]: tun0: LCP:  MAGICNUM[6] 0x5c512db9
Jul  7 04:24:05 aquina ppp[337]: tun0: LCP: deflink: State change Req-Sent --> Ack-Sent
Jul  7 04:24:05 aquina ppp[337]: tun0: LCP: deflink: RecvConfigRej(1) state = Ack-Sent
Jul  7 04:24:05 aquina ppp[337]: tun0: LCP:  ACFCOMP[2]
Jul  7 04:24:05 aquina ppp[337]: tun0: LCP:  PROTOCOMP[2]
Jul  7 04:24:05 aquina ppp[337]: tun0: LCP:  ACCMAP[6] 0x00000000
Jul  7 04:24:05 aquina ppp[337]: tun0: LCP:  QUALPROTO[8] proto c025, interval 30000ms
Jul  7 04:24:05 aquina ppp[337]: tun0: LCP: deflink: SendConfigReq(2) state = Ack-Sent
Jul  7 04:24:05 aquina ppp[337]: tun0: LCP:  MRU[4] 1492
Jul  7 04:24:05 aquina ppp[337]: tun0: LCP:  MAGICNUM[6] 0x526c492e
Jul  7 04:24:05 aquina ppp[337]: tun0: LCP: deflink: RecvConfigAck(2) state = Ack-Sent
Jul  7 04:24:05 aquina ppp[337]: tun0: LCP:  MRU[4] 1492
Jul  7 04:24:05 aquina ppp[337]: tun0: LCP:  MAGICNUM[6] 0x526c492e
Jul  7 04:24:05 aquina ppp[337]: tun0: LCP: deflink: State change Ack-Sent --> Opened
Jul  7 04:24:05 aquina ppp[337]: tun0: LCP: deflink: LayerUp
Jul  7 04:24:05 aquina ppp[337]: tun0: LCP: deflink: SendEchoRequest(0) state = Opened
Jul  7 04:24:05 aquina ppp[337]: tun0: Phase: bundle: Authenticate
Jul  7 04:24:05 aquina ppp[337]: tun0: Phase: deflink: his = CHAP 0x05, mine = none
Jul  7 04:24:05 aquina ppp[337]: tun0: Phase: Chap Input: CHALLENGE (16 bytes from duibr1)
Jul  7 04:24:05 aquina ppp[337]: tun0: Phase: Chap Output: RESPONSE (***my-login***)
Jul  7 04:24:05 aquina ppp[337]: tun0: LCP: deflink: RecvEchoReply(0) state = Opened
Jul  7 04:24:05 aquina ppp[337]: tun0: Phase: Chap Input: SUCCESS (access accepted : ***my-login***)
Jul  7 04:24:05 aquina ppp[337]: tun0: CCP: FSM: Using "deflink" as a transport
Jul  7 04:24:05 aquina ppp[337]: tun0: CCP: deflink: State change Initial --> Closed
Jul  7 04:24:05 aquina ppp[337]: tun0: CCP: deflink: LayerStart.
Jul  7 04:24:05 aquina ppp[337]: tun0: CCP: MPPE: Not usable without CHAP81
Jul  7 04:24:05 aquina ppp[337]: tun0: CCP: deflink: SendConfigReq(1) state = Closed
Jul  7 04:24:05 aquina ppp[337]: tun0: CCP:  DEFLATE[4] win 15
Jul  7 04:24:05 aquina ppp[337]: tun0: CCP:  PRED1[2] 
Jul  7 04:24:05 aquina ppp[337]: tun0: CCP: deflink: State change Closed --> Req-Sent
Jul  7 04:24:05 aquina ppp[337]: tun0: Phase: deflink: lcp -> open
Jul  7 04:24:05 aquina ppp[337]: tun0: Phase: bundle: Network
Jul  7 04:24:05 aquina ppp[337]: tun0: IPCP: FSM: Using "deflink" as a transport
Jul  7 04:24:05 aquina ppp[337]: tun0: IPCP: deflink: State change Initial --> Closed
Jul  7 04:24:05 aquina ppp[337]: tun0: IPCP: deflink: LayerStart.
Jul  7 04:24:05 aquina ppp[337]: tun0: IPCP: deflink: SendConfigReq(1) state = Closed
Jul  7 04:24:05 aquina ppp[337]: tun0: IPCP:  IPADDR[6] 10.0.0.1
Jul  7 04:24:05 aquina ppp[337]: tun0: IPCP:  COMPPROTO[6] 16 VJ slots with slot compression
Jul  7 04:24:05 aquina ppp[337]: tun0: IPCP: deflink: State change Closed --> Req-Sent
Jul  7 04:24:05 aquina ppp[337]: tun0: IPCP: deflink: RecvConfigReq(92) state = Req-Sent
Jul  7 04:24:05 aquina ppp[337]: tun0: IPCP:  IPADDR[6] 84.62.128.1
Jul  7 04:24:05 aquina ppp[337]: tun0: IPCP: deflink: SendConfigAck(92) state = Req-Sent
Jul  7 04:24:05 aquina ppp[337]: tun0: IPCP:  IPADDR[6] 84.62.128.1
Jul  7 04:24:05 aquina ppp[337]: tun0: IPCP: deflink: State change Req-Sent --> Ack-Sent
Jul  7 04:24:05 aquina ppp[337]: tun0: LCP: deflink: RecvProtocolRej(5) state = Opened
Jul  7 04:24:05 aquina ppp[337]: tun0: LCP: deflink: -- Protocol 0x80fd (Compression Control Protocol) was rejected!
Jul  7 04:24:05 aquina ppp[337]: tun0: CCP: deflink: State change Req-Sent --> Stopped
Jul  7 04:24:05 aquina ppp[337]: tun0: IPCP: deflink: RecvConfigRej(1) state = Ack-Sent
Jul  7 04:24:05 aquina ppp[337]: tun0: IPCP:  COMPPROTO[6] 16 VJ slots with slot compression
Jul  7 04:24:05 aquina ppp[337]: tun0: IPCP: deflink: SendConfigReq(2) state = Ack-Sent
Jul  7 04:24:05 aquina ppp[337]: tun0: IPCP:  IPADDR[6] 10.0.0.1
Jul  7 04:24:05 aquina ppp[337]: tun0: IPCP: deflink: RecvConfigNak(2) state = Ack-Sent
Jul  7 04:24:05 aquina ppp[337]: tun0: IPCP:  IPADDR[6] 84.62.131.143
Jul  7 04:24:05 aquina ppp[337]: tun0: IPCP:  IPADDR[6] changing address: 10.0.0.1  --> 84.62.131.143
Jul  7 04:24:05 aquina ppp[337]: tun0: IPCP: deflink: SendConfigReq(3) state = Ack-Sent
Jul  7 04:24:05 aquina ppp[337]: tun0: IPCP:  IPADDR[6] 84.62.131.143
Jul  7 04:24:05 aquina ppp[337]: tun0: IPCP: deflink: RecvConfigAck(3) state = Ack-Sent
Jul  7 04:24:05 aquina ppp[337]: tun0: IPCP:  IPADDR[6] 84.62.131.143
Jul  7 04:24:05 aquina ppp[337]: tun0: IPCP: deflink: State change Ack-Sent --> Opened
Jul  7 04:24:05 aquina ppp[337]: tun0: IPCP: deflink: LayerUp.
Jul  7 04:24:05 aquina ppp[337]: tun0: IPCP: myaddr 84.62.131.143 hisaddr = 84.62.128.1
Jul  7 04:24:05 aquina ppp[337]: tun0: Warning: 84.62.128.1: Change route failed: errno: No such process
Jul  7 04:24:35 aquina ppp[337]: tun0: LCP: deflink: SendEchoRequest(1) state = Opened
Jul  7 04:24:35 aquina ppp[337]: tun0: LCP: deflink: RecvEchoReply(1) state = Opened
Jul  7 04:24:51 aquina ppp[337]: tun0: LCP: deflink: RecvEchoRequest(0) state = Opened
Jul  7 04:24:51 aquina ppp[337]: tun0: LCP: deflink: SendEchoReply(0) state = Opened
Jul  7 04:25:06 aquina ppp[337]: tun0: LCP: deflink: SendEchoRequest(2) state = Opened
Jul  7 04:25:06 aquina ppp[337]: tun0: LCP: deflink: RecvEchoReply(2) state = Opened
Jul  7 04:25:36 aquina ppp[337]: tun0: LCP: deflink: SendEchoRequest(3) state = Opened
Jul  7 04:25:36 aquina ppp[337]: tun0: LCP: deflink: RecvEchoReply(3) state = Opened
Jul  7 04:26:06 aquina ppp[337]: tun0: LCP: deflink: SendEchoRequest(4) state = Opened
Jul  7 04:26:06 aquina ppp[337]: tun0: LCP: deflink: RecvEchoReply(4) state = Opened
Jul  7 04:26:37 aquina ppp[337]: tun0: LCP: deflink: SendEchoRequest(5) state = Opened
Jul  7 04:26:37 aquina ppp[337]: tun0: LCP: deflink: RecvEchoReply(5) state = Opened
Jul  7 04:26:56 aquina ppp[337]: tun0: LCP: deflink: RecvEchoRequest(1) state = Opened
Jul  7 04:26:56 aquina ppp[337]: tun0: LCP: deflink: SendEchoReply(1) state = Opened
Jul  7 04:27:07 aquina ppp[337]: tun0: LCP: deflink: SendEchoRequest(6) state = Opened
Jul  7 04:27:07 aquina ppp[337]: tun0: LCP: deflink: RecvEchoReply(6) state = Opened
Jul  7 04:27:37 aquina ppp[337]: tun0: LCP: deflink: SendEchoRequest(7) state = Opened
Jul  7 04:27:37 aquina ppp[337]: tun0: LCP: deflink: RecvEchoReply(7) state = Opened
# ppp.conf (PPPoE)
default:
        set log Phase Chat LCP IPCP CCP tun command
        enable lqr
        disable dns
        disable ipv6cp
        set mru 1492
        set mtu 1492
arcor:
        set device PPPoE:re0:
        set authname ***
        set authkey ***
        set dial
        set login
        set ifaddr 10.0.0.1/0 10.0.0.2/0
        add default HISADDR

More information about the Users mailing list