RealTek 8169S/8110S support.
Gary Allan
dragonfly at gallan.plus.com
Fri Dec 23 13:14:22 PST 2005
Matthew Dillon wrote:
>
> Do a boot -v and report which MII driver is currently attaching
> to the RE ethernet. It's probably the generic driver (ukphy), in
> which case we will need to port rgephy.c from FreeBSD to DragonFly.
>
> FreeBSD: sys/dev/mii/rge*
> DragonFly: sys/dev/netif/mii_layer/rge*
>
> There is some fairly minor porting work that needs to be done,
> which you can look at by looking at the cvs log history for some
> of the other MII source modules in DragonFly.
>
> -Matt
Please find attached my attempt to import support for the RealTek
8169S/8110S from FreeBSD. This supports my DLink 528(T) Card. Could
someone please review/test? The patch is against HEAD. I ran into two
main issues.
DragonFly is missing a mii_phy_update() function so I wrote an
rge_phy_update() replacement. I'm not sure this is 100% correct.
The card would not auto-negotiate a 1Gbit connection. I increased the
auto-negotiation interval to 17 seconds from five which solved the
problem. There was PR report with this problem and solution for re(4)
and a Cisco switch but I can no longer find the link.
I can see why the cards are $12. I'm slightly disappointed that two of
these cards back to back only manage ~150Mbit/s but it's an improvement
over my built-in vr0.
Regards
G.Allan
ifconfig re0
re0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500
options=1b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING>
inet6 fe80::213:46ff:fe2f:5a8e%re0 prefixlen 64 scopeid 0x3
ether 00:13:46:2f:5a:8e
media: Ethernet autoselect (1000baseT <full-duplex>)
status: active
dmesg | grep miibus2
miibus2: <MII bus> on re0
rgephy0: <RTL8169S/8110S media interface> on miibus2
Index: sys/conf/files
===================================================================
RCS file: /home/dcvs/src/sys/conf/files,v
retrieving revision 1.113
diff -u -r1.113 files
--- sys/conf/files 21 Dec 2005 16:37:15 -0000 1.113
+++ sys/conf/files 23 Dec 2005 14:57:24 -0000
@@ -271,6 +271,7 @@
dev/netif/mii_layer/lxtphy.c optional miibus
dev/netif/mii_layer/qsphy.c optional miibus
dev/netif/mii_layer/acphy.c optional miibus
+dev/netif/mii_layer/rgephy.c optional miibus
dev/netif/mii_layer/ruephy.c optional miibus
dev/netif/mii_layer/miibus_if.m optional miibus
dev/raid/mlx/mlx_disk.c optional mlx
Index: sys/dev/netif/mii_layer/Makefile
===================================================================
RCS file: /home/dcvs/src/sys/dev/netif/mii_layer/Makefile,v
retrieving revision 1.6
diff -u -r1.6 Makefile
--- sys/dev/netif/mii_layer/Makefile 24 Oct 2005 16:45:19 -0000 1.6
+++ sys/dev/netif/mii_layer/Makefile 23 Dec 2005 15:03:07 -0000
@@ -6,7 +6,7 @@
SRCS += miibus_if.h device_if.h miibus_if.c e1000phy.c exphy.c nsphy.c
SRCS += mlphy.c tlphy.c rlphy.c amphy.c dcphy.c pnphy.c nsgphy.c
SRCS += pnaphy.c brgphy.c xmphy.c inphy.c lxtphy.c qsphy.c acphy.c
-SRCS += ruephy.c nvphy.c
+SRCS += rgephy.c ruephy.c nvphy.c
.include "./Makefile.miidevs"
Index: sys/dev/netif/mii_layer/miidevs
===================================================================
RCS file: /home/dcvs/src/sys/dev/netif/mii_layer/miidevs,v
retrieving revision 1.5
diff -u -r1.5 miidevs
--- sys/dev/netif/mii_layer/miidevs 10 Feb 2004 21:14:14 -0000 1.5
+++ sys/dev/netif/mii_layer/miidevs 23 Dec 2005 20:43:43 -0000
@@ -91,6 +91,8 @@
/* Don't know what's going on here. */
oui xxDAVICOM 0x006040 Davicom Semiconductor
+/* This is the OUI of the gigE PHY in the RealTek 8169S/8110S chips */
+oui xxREALTEK 0x000732
/*
* List of known models. Grouped by oui.
@@ -144,6 +146,7 @@
/* RealTek Semiconductor PHYs */
model REALTEK RTL8201L 0x0020 RTL8201L 10/100 media interface
+model xxREALTEK RTL8169S 0x0011 RTL8169S/8110S media interface
/* Seeq PHYs */
model xxSEEQ 80220 0x0003 Seeq 80220 10/100 media interface
Index: sys/dev/netif/mii_layer/miidevs.h
===================================================================
RCS file: /home/dcvs/src/sys/dev/netif/mii_layer/miidevs.h,v
retrieving revision 1.5
diff -u -r1.5 miidevs.h
--- sys/dev/netif/mii_layer/miidevs.h 10 Feb 2004 21:14:14 -0000 1.5
+++ sys/dev/netif/mii_layer/miidevs.h 23 Dec 2005 20:45:34 -0000
@@ -1,10 +1,10 @@
-/* $DragonFly: src/sys/dev/netif/mii_layer/miidevs.h,v 1.5 2004/02/10 21:14:14 hmp Exp $ */
+/* $DragonFly$ */
/*
* THIS FILE AUTOMATICALLY GENERATED. DO NOT EDIT.
*
* generated from:
- * DragonFly: src/sys/dev/netif/mii_layer/miidevs,v 1.4 2004/02/09 16:41:33 hmp Exp
+ * DragonFly: src/sys/dev/netif/mii_layer/miidevs,v 1.5 2004/02/10 21:14:14 hmp Exp
*/
/* $FreeBSD: src/sys/dev/mii/miidevs,v 1.4.2.13 2003/07/22 02:12:55 ps Exp $ */
/*$NetBSD: miidevs,v 1.6 1999/05/14 11:37:30 drochner Exp $*/
@@ -98,6 +98,8 @@
/* Don't know what's going on here. */
#define MII_OUI_xxDAVICOM 0x006040 /* Davicom Semiconductor */
+/* This is the OUI of the gigE PHY in the RealTek 8169S/8110S chips */
+#define MII_OUI_xxREALTEK 0x000732 /* */
/*
* List of known models. Grouped by oui.
@@ -178,6 +180,8 @@
/* RealTek Semiconductor PHYs */
#define MII_MODEL_REALTEK_RTL8201L 0x0020
#define MII_STR_REALTEK_RTL8201L "RTL8201L 10/100 media interface"
+#define MII_MODEL_xxREALTEK_RTL8169S 0x0011
+#define MII_STR_xxREALTEK_RTL8169S "RTL8169S/8110S media interface"
/* Seeq PHYs */
#define MII_MODEL_xxSEEQ_80220 0x0003
Index: sys/dev/netif/mii_layer/rgephy.c
===================================================================
RCS file: sys/dev/netif/mii_layer/rgephy.c
diff -N sys/dev/netif/mii_layer/rgephy.c
--- /dev/null 1 Jan 1970 00:00:00 -0000
+++ sys/dev/netif/mii_layer/rgephy.c 23 Dec 2005 20:13:42 -0000
@@ -0,0 +1,504 @@
+/*-
+ * Copyright (c) 2003
+ * Bill Paul <wpaul at xxxxxxxxxxxxx>. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ * 1. Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * 3. All advertising materials mentioning features or use of this software
+ * must display the following acknowledgement:
+ * This product includes software developed by Bill Paul.
+ * 4. Neither the name of the author nor the names of any co-contributors
+ * may be used to endorse or promote products derived from this software
+ * without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Bill Paul AND CONTRIBUTORS ``AS IS'' AND
+ * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ * ARE DISCLAIMED. IN NO EVENT SHALL Bill Paul OR THE VOICES IN HIS HEAD
+ * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
+ * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
+ * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+ * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
+ * THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ * $FreeBSD: /repoman/r/ncvs/src/sys/dev/mii/rgephy.c,v 1.7 2005/09/30 19:39:27 imp Exp $
+ * $DragonFly: $
+ */
+
+#include <sys/cdefs.h>
+
+/*
+ * Driver for the RealTek 8169S/8110S internal 10/100/1000 PHY.
+ */
+
+#include <sys/param.h>
+#include <sys/systm.h>
+#include <sys/kernel.h>
+#include <sys/socket.h>
+#include <sys/bus.h>
+
+#include <machine/clock.h>
+
+#include <net/if.h>
+#include <net/if_arp.h>
+#include <net/if_media.h>
+
+#include <dev/netif/mii_layer/mii.h>
+#include <dev/netif/mii_layer/miivar.h>
+#include <dev/netif/mii_layer/rgephyreg.h>
+
+#include "miidevs.h"
+
+#include "miibus_if.h"
+
+#include <machine/bus.h>
+#include <dev/netif/re/if_rereg.h>
+
+static int rgephy_probe(device_t);
+static int rgephy_attach(device_t);
+static int rgephy_detach(device_t);
+static void rgephy_update(struct mii_softc *, int);
+
+static device_method_t rgephy_methods[] = {
+ /* device interface */
+ DEVMETHOD(device_probe, rgephy_probe),
+ DEVMETHOD(device_attach, rgephy_attach),
+ DEVMETHOD(device_detach, rgephy_detach),
+ DEVMETHOD(device_shutdown, bus_generic_shutdown),
+ { 0, 0 }
+};
+
+static devclass_t rgephy_devclass;
+
+static driver_t rgephy_driver = {
+ "rgephy",
+ rgephy_methods,
+ sizeof(struct mii_softc)
+};
+
+DRIVER_MODULE(rgephy, miibus, rgephy_driver, rgephy_devclass, 0, 0);
+
+static int rgephy_service(struct mii_softc *, struct mii_data *, int);
+static void rgephy_status(struct mii_softc *);
+static int rgephy_mii_phy_auto(struct mii_softc *);
+static void rgephy_reset(struct mii_softc *);
+static void rgephy_loop(struct mii_softc *);
+static void rgephy_load_dspcode(struct mii_softc *);
+static int rgephy_mii_model;
+
+static int
+rgephy_probe(device_t dev)
+{
+ struct mii_attach_args *ma;
+
+ ma = device_get_ivars(dev);
+
+ if (MII_OUI(ma->mii_id1, ma->mii_id2) == MII_OUI_xxREALTEK &&
+ MII_MODEL(ma->mii_id2) == MII_MODEL_xxREALTEK_RTL8169S) {
+ device_set_desc(dev, MII_STR_xxREALTEK_RTL8169S);
+ return(0);
+ }
+
+ return(ENXIO);
+}
+
+static int
+rgephy_attach(device_t dev)
+{
+ struct mii_softc *sc;
+ struct mii_attach_args *ma;
+ struct mii_data *mii;
+ const char *sep = "";
+
+ sc = device_get_softc(dev);
+ ma = device_get_ivars(dev);
+ sc->mii_dev = device_get_parent(dev);
+ mii = device_get_softc(sc->mii_dev);
+ LIST_INSERT_HEAD(&mii->mii_phys, sc, mii_list);
+
+ sc->mii_inst = mii->mii_instance;
+ sc->mii_phy = ma->mii_phyno;
+ sc->mii_service = rgephy_service;
+ sc->mii_pdata = mii;
+
+ sc->mii_flags |= MIIF_NOISOLATE;
+ mii->mii_instance++;
+
+#define ADD(m, c) ifmedia_add(&mii->mii_media, (m), (c), NULL)
+#define PRINT(s) printf("%s%s", sep, s); sep = ", "
+
+ ADD(IFM_MAKEWORD(IFM_ETHER, IFM_NONE, 0, sc->mii_inst),
+ BMCR_ISO);
+#if 0
+ ADD(IFM_MAKEWORD(IFM_ETHER, IFM_100_TX, IFM_LOOP, sc->mii_inst),
+ BMCR_LOOP|BMCR_S100);
+#endif
+
+ rgephy_mii_model = MII_MODEL(ma->mii_id2);
+ rgephy_reset(sc);
+
+ sc->mii_capabilities = PHY_READ(sc, MII_BMSR) & ma->mii_capmask;
+ sc->mii_capabilities &= ~BMSR_ANEG;
+
+ device_printf(dev, " ");
+ mii_add_media(sc, sc->mii_capabilities);
+ ADD(IFM_MAKEWORD(IFM_ETHER, IFM_1000_T, 0, sc->mii_inst),
+ RGEPHY_BMCR_FDX);
+ PRINT(", 1000baseTX");
+ ADD(IFM_MAKEWORD(IFM_ETHER, IFM_1000_T, IFM_FDX, sc->mii_inst), 0);
+ PRINT("1000baseTX-FDX");
+ ADD(IFM_MAKEWORD(IFM_ETHER, IFM_AUTO, 0, sc->mii_inst), 0);
+ PRINT("auto");
+
+ printf("\n");
+#undef ADD
+#undef PRINT
+
+ MIIBUS_MEDIAINIT(sc->mii_dev);
+ return(0);
+}
+
+static int
+rgephy_detach(device_t dev)
+{
+ struct mii_softc *sc;
+ struct mii_data *mii;
+
+ sc = device_get_softc(dev);
+ mii = device_get_softc(device_get_softc(dev));
+ mii_phy_auto_stop(sc);
+ sc->mii_dev = NULL;
+ LIST_REMOVE(sc, mii_list);
+
+ return (0);
+}
+
+static void
+rgephy_update(struct mii_softc *sc, int cmd)
+{
+ struct mii_data *mii = sc->mii_pdata;
+
+ if (sc->mii_active != mii->mii_media_active ||
+ cmd == MII_MEDIACHG) {
+ MIIBUS_STATCHG(sc->mii_dev);
+ sc->mii_active = mii->mii_media_active;
+ }
+/*
+ if (sc->mii_status != mii->mii_media_status) {
+ MIIBUS_LINKCHG(sc->mii_dev);
+ sc->mii_status = mii->mii_media_status;
+ }
+*/
+}
+
+static int
+rgephy_service(struct mii_softc *sc, struct mii_data *mii, int cmd)
+{
+ struct ifmedia_entry *ife = mii->mii_media.ifm_cur;
+ int reg, speed, gig;
+
+ switch (cmd) {
+ case MII_POLLSTAT:
+ /*
+ * If we're not polling our PHY instance, just return.
+ */
+ if (IFM_INST(ife->ifm_media) != sc->mii_inst)
+ return (0);
+ break;
+
+ case MII_MEDIACHG:
+ /*
+ * If the media indicates a different PHY instance,
+ * isolate ourselves.
+ */
+ if (IFM_INST(ife->ifm_media) != sc->mii_inst) {
+ reg = PHY_READ(sc, MII_BMCR);
+ PHY_WRITE(sc, MII_BMCR, reg | BMCR_ISO);
+ return (0);
+ }
+
+ /*
+ * If the interface is not up, don't do anything.
+ */
+ if ((mii->mii_ifp->if_flags & IFF_UP) == 0)
+ break;
+
+ rgephy_reset(sc); /* XXX hardware bug work-around */
+
+ switch (IFM_SUBTYPE(ife->ifm_media)) {
+ case IFM_AUTO:
+#ifdef foo
+ /*
+ * If we're already in auto mode, just return.
+ */
+ if (PHY_READ(sc, RGEPHY_MII_BMCR) & RGEPHY_BMCR_AUTOEN)
+ return (0);
+#endif
+ (void) rgephy_mii_phy_auto(sc);
+ break;
+ case IFM_1000_T:
+ speed = RGEPHY_S1000;
+ goto setit;
+ case IFM_100_TX:
+ speed = RGEPHY_S100;
+ goto setit;
+ case IFM_10_T:
+ speed = RGEPHY_S10;
+setit:
+ rgephy_loop(sc);
+ if ((ife->ifm_media & IFM_GMASK) == IFM_FDX) {
+ speed |= RGEPHY_BMCR_FDX;
+ gig = RGEPHY_1000CTL_AFD;
+ } else {
+ gig = RGEPHY_1000CTL_AHD;
+ }
+
+ PHY_WRITE(sc, RGEPHY_MII_1000CTL, 0);
+ PHY_WRITE(sc, RGEPHY_MII_BMCR, speed);
+ PHY_WRITE(sc, RGEPHY_MII_ANAR, RGEPHY_SEL_TYPE);
+
+ if (IFM_SUBTYPE(ife->ifm_media) != IFM_1000_T)
+ break;
+
+ PHY_WRITE(sc, RGEPHY_MII_1000CTL, gig);
+ PHY_WRITE(sc, RGEPHY_MII_BMCR,
+ speed|RGEPHY_BMCR_AUTOEN|RGEPHY_BMCR_STARTNEG);
+
+ /*
+ * When settning the link manually, one side must
+ * be the master and the other the slave. However
+ * ifmedia doesn't give us a good way to specify
+ * this, so we fake it by using one of the LINK
+ * flags. If LINK0 is set, we program the PHY to
+ * be a master, otherwise it's a slave.
+ */
+ if ((mii->mii_ifp->if_flags & IFF_LINK0)) {
+ PHY_WRITE(sc, RGEPHY_MII_1000CTL,
+ gig|RGEPHY_1000CTL_MSE|RGEPHY_1000CTL_MSC);
+ } else {
+ PHY_WRITE(sc, RGEPHY_MII_1000CTL,
+ gig|RGEPHY_1000CTL_MSE);
+ }
+ break;
+#ifdef foo
+ case IFM_NONE:
+ PHY_WRITE(sc, MII_BMCR, BMCR_ISO|BMCR_PDOWN);
+ break;
+#endif
+ case IFM_100_T4:
+ default:
+ return (EINVAL);
+ }
+ break;
+
+ case MII_TICK:
+ /*
+ * If we're not currently selected, just return.
+ */
+ if (IFM_INST(ife->ifm_media) != sc->mii_inst)
+ return (0);
+
+ /*
+ * Is the interface even up?
+ */
+ if ((mii->mii_ifp->if_flags & IFF_UP) == 0)
+ return (0);
+
+ /*
+ * Only used for autonegotiation.
+ */
+ if (IFM_SUBTYPE(ife->ifm_media) != IFM_AUTO)
+ break;
+
+ /*
+ * Check to see if we have link. If we do, we don't
+ * need to restart the autonegotiation process. Read
+ * the BMSR twice in case it's latched.
+ */
+ reg = PHY_READ(sc, RE_GMEDIASTAT);
+ if (reg & RE_GMEDIASTAT_LINK)
+ break;
+
+ /*
+ * Only retry autonegotiation every 17 seconds.
+ */
+ if (++sc->mii_ticks <= 17/*10*/)
+ break;
+
+ sc->mii_ticks = 0;
+ rgephy_mii_phy_auto(sc);
+ return (0);
+ }
+
+ /* Update the media status. */
+ rgephy_status(sc);
+
+ /*
+ * Callback if something changed. Note that we need to poke
+ * the DSP on the RealTek PHYs if the media changes.
+ *
+ */
+ if (sc->mii_active != mii->mii_media_active ||
+ /* sc->mii_status != mii->mii_media_status || */
+ cmd == MII_MEDIACHG) {
+ rgephy_load_dspcode(sc);
+ }
+ rgephy_update(sc, cmd);
+ return (0);
+}
+
+static void
+rgephy_status(struct mii_softc *sc)
+{
+ struct mii_data *mii = sc->mii_pdata;
+ int bmsr, bmcr;
+
+ mii->mii_media_status = IFM_AVALID;
+ mii->mii_media_active = IFM_ETHER;
+
+ bmsr = PHY_READ(sc, RE_GMEDIASTAT);
+
+ if (bmsr & RE_GMEDIASTAT_LINK)
+ mii->mii_media_status |= IFM_ACTIVE;
+ bmsr = PHY_READ(sc, RGEPHY_MII_BMSR);
+
+ bmcr = PHY_READ(sc, RGEPHY_MII_BMCR);
+
+ if (bmcr & RGEPHY_BMCR_LOOP)
+ mii->mii_media_active |= IFM_LOOP;
+
+ if (bmcr & RGEPHY_BMCR_AUTOEN) {
+ if ((bmsr & RGEPHY_BMSR_ACOMP) == 0) {
+ /* Erg, still trying, I guess... */
+ mii->mii_media_active |= IFM_NONE;
+ return;
+ }
+ }
+
+ bmsr = PHY_READ(sc, RE_GMEDIASTAT);
+ if (bmsr & RE_GMEDIASTAT_10MBPS)
+ mii->mii_media_active |= IFM_10_T;
+ if (bmsr & RE_GMEDIASTAT_100MBPS)
+ mii->mii_media_active |= IFM_100_TX;
+ if (bmsr & RE_GMEDIASTAT_1000MBPS)
+ mii->mii_media_active |= IFM_1000_T;
+ if (bmsr & RE_GMEDIASTAT_FDX)
+ mii->mii_media_active |= IFM_FDX;
+
+ return;
+}
+
+static int
+rgephy_mii_phy_auto(struct mii_softc *mii)
+{
+ rgephy_loop(mii);
+ rgephy_reset(mii);
+
+ PHY_WRITE(mii, RGEPHY_MII_ANAR, mii_bmsr_media_to_anar(mii));
+ DELAY(1000);
+ PHY_WRITE(mii, RGEPHY_MII_1000CTL, RGEPHY_1000CTL_AFD);
+ DELAY(1000);
+ PHY_WRITE(mii, RGEPHY_MII_BMCR,
+ RGEPHY_BMCR_AUTOEN | RGEPHY_BMCR_STARTNEG);
+ DELAY(100);
+
+ return (EJUSTRETURN);
+}
+
+static void
+rgephy_loop(struct mii_softc *sc)
+{
+ u_int32_t bmsr;
+ int i;
+
+ PHY_WRITE(sc, RGEPHY_MII_BMCR, RGEPHY_BMCR_PDOWN);
+ DELAY(1000);
+
+ for (i = 0; i < 15000; i++) {
+ bmsr = PHY_READ(sc, RGEPHY_MII_BMSR);
+ if (!(bmsr & RGEPHY_BMSR_LINK)) {
+#if 0
+ device_printf(sc->mii_dev, "looped %d\n", i);
+#endif
+ break;
+ }
+ DELAY(10);
+ }
+}
+
+#define PHY_SETBIT(x, y, z) \
+ PHY_WRITE(x, y, (PHY_READ(x, y) | (z)))
+#define PHY_CLRBIT(x, y, z) \
+ PHY_WRITE(x, y, (PHY_READ(x, y) & ~(z)))
+
+/*
+ * Initialize RealTek PHY per the datasheet. The DSP in the PHYs of
+ * existing revisions of the 8169S/8110S chips need to be tuned in
+ * order to reliably negotiate a 1000Mbps link. Later revs of the
+ * chips may not require this software tuning.
+ */
+static void
+rgephy_load_dspcode(struct mii_softc *sc)
+{
+ int val;
+
+ PHY_WRITE(sc, 31, 0x0001);
+ PHY_WRITE(sc, 21, 0x1000);
+ PHY_WRITE(sc, 24, 0x65C7);
+ PHY_CLRBIT(sc, 4, 0x0800);
+ val = PHY_READ(sc, 4) & 0xFFF;
+ PHY_WRITE(sc, 4, val);
+ PHY_WRITE(sc, 3, 0x00A1);
+ PHY_WRITE(sc, 2, 0x0008);
+ PHY_WRITE(sc, 1, 0x1020);
+ PHY_WRITE(sc, 0, 0x1000);
+ PHY_SETBIT(sc, 4, 0x0800);
+ PHY_CLRBIT(sc, 4, 0x0800);
+ val = (PHY_READ(sc, 4) & 0xFFF) | 0x7000;
+ PHY_WRITE(sc, 4, val);
+ PHY_WRITE(sc, 3, 0xFF41);
+ PHY_WRITE(sc, 2, 0xDE60);
+ PHY_WRITE(sc, 1, 0x0140);
+ PHY_WRITE(sc, 0, 0x0077);
+ val = (PHY_READ(sc, 4) & 0xFFF) | 0xA000;
+ PHY_WRITE(sc, 4, val);
+ PHY_WRITE(sc, 3, 0xDF01);
+ PHY_WRITE(sc, 2, 0xDF20);
+ PHY_WRITE(sc, 1, 0xFF95);
+ PHY_WRITE(sc, 0, 0xFA00);
+ val = (PHY_READ(sc, 4) & 0xFFF) | 0xB000;
+ PHY_WRITE(sc, 4, val);
+ PHY_WRITE(sc, 3, 0xFF41);
+ PHY_WRITE(sc, 2, 0xDE20);
+ PHY_WRITE(sc, 1, 0x0140);
+ PHY_WRITE(sc, 0, 0x00BB);
+ val = (PHY_READ(sc, 4) & 0xFFF) | 0xF000;
+ PHY_WRITE(sc, 4, val);
+ PHY_WRITE(sc, 3, 0xDF01);
+ PHY_WRITE(sc, 2, 0xDF20);
+ PHY_WRITE(sc, 1, 0xFF95);
+ PHY_WRITE(sc, 0, 0xBF00);
+ PHY_SETBIT(sc, 4, 0x0800);
+ PHY_CLRBIT(sc, 4, 0x0800);
+ PHY_WRITE(sc, 31, 0x0000);
+
+ DELAY(40);
+}
+
+static void
+rgephy_reset(struct mii_softc *sc)
+{
+ mii_phy_reset(sc);
+ DELAY(1000);
+ rgephy_load_dspcode(sc);
+
+ return;
+}
Index: sys/dev/netif/mii_layer/rgephyreg.h
===================================================================
RCS file: sys/dev/netif/mii_layer/rgephyreg.h
diff -N sys/dev/netif/mii_layer/rgephyreg.h
--- /dev/null 1 Jan 1970 00:00:00 -0000
+++ sys/dev/netif/mii_layer/rgephyreg.h 23 Dec 2005 15:00:20 -0000
@@ -0,0 +1,142 @@
+/*-
+ * Copyright (c) 2003
+ * Bill Paul <wpaul at xxxxxxxxxxxxx>. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ * 1. Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * 3. All advertising materials mentioning features or use of this software
+ * must display the following acknowledgement:
+ * This product includes software developed by Bill Paul.
+ * 4. Neither the name of the author nor the names of any co-contributors
+ * may be used to endorse or promote products derived from this software
+ * without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Bill Paul AND CONTRIBUTORS ``AS IS'' AND
+ * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ * ARE DISCLAIMED. IN NO EVENT SHALL Bill Paul OR THE VOICES IN HIS HEAD
+ * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
+ * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
+ * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+ * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
+ * THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ * $FreeBSD: src/sys/dev/mii/rgephyreg.h,v 1.2 2005/01/06 01:42:56 imp Exp $
+ */
+
+#ifndef _DEV_MII_RGEPHYREG_H_
+#define _DEV_MII_RGEPHYREG_H_
+
+/*
+ * RealTek 8169S/8110S gigE PHY registers
+ */
+
+#define RGEPHY_MII_BMCR 0x00
+#define RGEPHY_BMCR_RESET 0x8000
+#define RGEPHY_BMCR_LOOP 0x4000
+#define RGEPHY_BMCR_SPD0 0x2000 /* speed select, lower bit */
+#define RGEPHY_BMCR_AUTOEN 0x1000 /* Autoneg enabled */
+#define RGEPHY_BMCR_PDOWN 0x0800 /* Power down */
+#define RGEPHY_BMCR_ISO 0x0400 /* Isolate */
+#define RGEPHY_BMCR_STARTNEG 0x0200 /* Restart autoneg */
+#define RGEPHY_BMCR_FDX 0x0100 /* Duplex mode */
+#define RGEPHY_BMCR_CTEST 0x0080 /* Collision test enable */
+#define RGEPHY_BMCR_SPD1 0x0040 /* Speed select, upper bit */
+
+#define RGEPHY_S1000 RGEPHY_BMCR_SPD1 /* 1000mbps */
+#define RGEPHY_S100 RGEPHY_BMCR_SPD0 /* 100mpbs */
+#define RGEPHY_S10 0 /* 10mbps */
+
+#define RGEPHY_MII_BMSR 0x01
+#define RGEPHY_BMSR_100T4 0x8000 /* 100 base T4 capable */
+#define RGEPHY_BMSR_100TXFDX 0x4000 /* 100 base Tx full duplex capable */
+#define RGEPHY_BMSR_100TXHDX 0x2000 /* 100 base Tx half duplex capable */
+#define RGEPHY_BMSR_10TFDX 0x1000 /* 10 base T full duplex capable */
+#define RGEPHY_BMSR_10THDX 0x0800 /* 10 base T half duplex capable */
+#define RGEPHY_BMSR_100T2FDX 0x0400 /* 100 base T2 full duplex capable */
+#define RGEPHY_BMSR_100T2HDX 0x0200 /* 100 base T2 half duplex capable */
+#define RGEPHY_BMSR_EXTSTS 0x0100 /* Extended status present */
+#define RGEPHY_BMSR_PRESUB 0x0040 /* Preamble surpression */
+#define RGEPHY_BMSR_ACOMP 0x0020 /* Autoneg complete */
+#define RGEPHY_BMSR_RFAULT 0x0010 /* Remote fault condition occured */
+#define RGEPHY_BMSR_ANEG 0x0008 /* Autoneg capable */
+#define RGEPHY_BMSR_LINK 0x0004 /* Link status */
+#define RGEPHY_BMSR_JABBER 0x0002 /* Jabber detected */
+#define RGEPHY_BMSR_EXT 0x0001 /* Extended capability */
+
+#define RGEPHY_MII_ANAR 0x04
+#define RGEPHY_ANAR_NP 0x8000 /* Next page */
+#define RGEPHY_ANAR_RF 0x2000 /* Remote fault */
+#define RGEPHY_ANAR_ASP 0x0800 /* Asymmetric Pause */
+#define RGEPHY_ANAR_PC 0x0400 /* Pause capable */
+#define RGEPHY_ANAR_T4 0x0200 /* local device supports 100bT4 */
+#define RGEPHY_ANAR_TX_FD 0x0100 /* local device supports 100bTx FD */
+#define RGEPHY_ANAR_TX 0x0080 /* local device supports 100bTx */
+#define RGEPHY_ANAR_10_FD 0x0040 /* local device supports 10bT FD */
+#define RGEPHY_ANAR_10 0x0020 /* local device supports 10bT */
+#define RGEPHY_ANAR_SEL 0x001F /* selector field, 00001=Ethernet */
+
+#define RGEPHY_MII_ANLPAR 0x05
+#define RGEPHY_ANLPAR_NP 0x8000 /* Next page */
+#define RGEPHY_ANLPAR_RF 0x2000 /* Remote fault */
+#define RGEPHY_ANLPAR_ASP 0x0800 /* Asymmetric Pause */
+#define RGEPHY_ANLPAR_PC 0x0400 /* Pause capable */
+#define RGEPHY_ANLPAR_T4 0x0200 /* link partner supports 100bT4 */
+#define RGEPHY_ANLPAR_TX_FD 0x0100 /* link partner supports 100bTx FD */
+#define RGEPHY_ANLPAR_TX 0x0080 /* link partner supports 100bTx */
+#define RGEPHY_ANLPAR_10_FD 0x0040 /* link partner supports 10bT FD */
+#define RGEPHY_ANLPAR_10 0x0020 /* link partner supports 10bT */
+#define RGEPHY_ANLPAR_SEL 0x001F /* selector field, 00001=Ethernet */
+
+#define RGEPHY_SEL_TYPE 0x0001 /* ethernet */
+
+#define RGEPHY_MII_ANER 0x06
+#define RGEPHY_ANER_PDF 0x0010 /* Parallel detection fault */
+#define RGEPHY_ANER_LPNP 0x0008 /* Link partner can next page */
+#define RGEPHY_ANER_NP 0x0004 /* Local PHY can next page */
+#define RGEPHY_ANER_RX 0x0002 /* Next page received */
+#define RGEPHY_ANER_LPAN 0x0001 /* Link partner autoneg capable */
+
+#define RGEPHY_MII_NEXTP 0x07 /* Next page */
+
+#define RGEPHY_MII_NEXTP_LP 0x08 /* Next page of link partner */
+
+#define RGEPHY_MII_1000CTL 0x09 /* 1000baseT control */
+#define RGEPHY_1000CTL_TST 0xE000 /* test modes */
+#define RGEPHY_1000CTL_MSE 0x1000 /* Master/Slave manual enable */
+#define RGEPHY_1000CTL_MSC 0x0800 /* Master/Slave select */
+#define RGEPHY_1000CTL_RD 0x0400 /* Repeater/DTE */
+#define RGEPHY_1000CTL_AFD 0x0200 /* Advertise full duplex */
+#define RGEPHY_1000CTL_AHD 0x0100 /* Advertise half duplex */
+
+#define RGEPHY_TEST_TX_JITTER 0x2000
+#define RGEPHY_TEST_TX_JITTER_MASTER_MODE 0x4000
+#define RGEPHY_TEST_TX_JITTER_SLAVE_MODE 0x6000
+#define RGEPHY_TEST_TX_DISTORTION 0x8000
+
+#define RGEPHY_MII_1000STS 0x0A /* 1000baseT status */
+#define RGEPHY_1000STS_MSF 0x8000 /* Master/slave fault */
+#define RGEPHY_1000STS_MSR 0x4000 /* Master/slave result */
+#define RGEPHY_1000STS_LRS 0x2000 /* Local receiver status */
+#define RGEPHY_1000STS_RRS 0x1000 /* Remote receiver status */
+#define RGEPHY_1000STS_LPFD 0x0800 /* Link partner can FD */
+#define RGEPHY_1000STS_LPHD 0x0400 /* Link partner can HD */
+#define RGEPHY_1000STS_IEC 0x00FF /* Idle error count */
+
+#define RGEPHY_MII_EXTSTS 0x0F /* Extended status */
+#define RGEPHY_EXTSTS_X_FD_CAP 0x8000 /* 1000base-X FD capable */
+#define RGEPHY_EXTSTS_X_HD_CAP 0x4000 /* 1000base-X HD capable */
+#define RGEPHY_EXTSTS_T_FD_CAP 0x2000 /* 1000base-T FD capable */
+#define RGEPHY_EXTSTS_T_HD_CAP 0x1000 /* 1000base-T HD capable */
+
+
+
+#endif /* _DEV_RGEPHY_MIIREG_H_ */
More information about the Submit
mailing list