kernel panic under install CD boot (cd9660-related)
Jan Martin Mathiassen
dfbsd at mindriot.as
Mon Aug 25 05:25:17 PDT 2008
So, I finally managed to get a verbose boot dmesg after about a week's
worth of trying random shit just to get it to boot, where even pxe was
b0rked.
Enjoy the dmesg.txt, I sure didn't. I hope that'll be helpful in getting
things one step further.
Copyright (c) 2003-2008 The DragonFly Project.
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
DragonFly 2.1.0-DEVELOPMENT #0: Fri Aug 22 00:56:49 CEST 2008
root at chlamydia.fs.ei.tum.de:/usr/obj/usr/src/sys/GENERIC
Calibrating clock(s) ... TSC clock: 2668869510 Hz, i8254 clock: 1193213 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
CLK_USE_TSC_CALIBRATION not specified - using old calibration method
CPU: Intel(R) Core(TM)2 CPU 6700 @ 2.66GHz (2668.81-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x6f6 Stepping = 6
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Features2=0xe3bd<SSE3,RSVD2,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,XTPR,RSVD15>
Hyperthreading: 2 logical CPUs
real memory = 3153723392 (3079808K bytes)
Physical memory chunk(s):
0x00001000 - 0x0009dfff, 643072 bytes (157 pages)
0x0087d000 - 0xbbf8ffff, 3144757248 bytes (767763 pages)
avail memory = 3050295296 (2978804K bytes)
bios32: Found BIOS32 Service Directory header at 0xc00f0000
bios32: Entry = 0xf0010 (c00f0010) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0x31
pnpbios: Found PnP BIOS data at 0xc00f65c0
pnpbios: Entry = f0000:795a Rev = 1.0
Other BIOS signatures found:
Preloaded elf kernel "/kernel.BOOTP" at 0xc0850000.
Preloaded elf module "/modules/acpi.ko" at 0xc0850240.
wlan: <802.11 Link Layer>
crypto: <crypto core>
Pentium Pro MTRR support enabled
md0: Malloc disk
Math emulator present
pci_open(1): mode 1 addr port (0x0cf8) is 0x80030004
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=29a08086)
pcibios: BIOS version 3.00
Using $PIR table, 16 entries at 0xc00f6410
PCI-Only Interrupts: none
Location Bus Device Pin Link IRQs
embedded 0 1 A 0x60 3 4 5 6 7 10 11 12 14 15
embedded 0 1 B 0x61 3 4 5 6 7 10 11 12 14 15
embedded 0 1 C 0x62 3 4 5 6 7 10 11 12 14 15
embedded 0 1 D 0x63 3 4 5 6 7 10 11 12 14 15
embedded 0 2 A 0x60 3 4 5 6 7 10 11 12 14 15
embedded 0 3 A 0x60 3 4 5 6 7 10 11 12 14 15
embedded 0 3 B 0x61 3 4 5 6 7 10 11 12 14 15
embedded 0 3 C 0x62 3 4 5 6 7 10 11 12 14 15
embedded 0 31 A 0x62 3 4 5 6 7 10 11 12 14 15
embedded 0 31 B 0x63 3 4 5 6 7 10 11 12 14 15
embedded 0 31 C 0x62 3 4 5 6 7 10 11 12 14 15
embedded 0 29 A 0x6b 3 4 5 6 7 10 11 12 14 15
embedded 0 29 B 0x63 3 4 5 6 7 10 11 12 14 15
embedded 0 29 C 0x62 3 4 5 6 7 10 11 12 14 15
embedded 0 29 D 0x60 3 4 5 6 7 10 11 12 14 15
embedded 0 26 A 0x60 3 4 5 6 7 10 11 12 14 15
embedded 0 26 B 0x61 3 4 5 6 7 10 11 12 14 15
embedded 0 26 C 0x62 3 4 5 6 7 10 11 12 14 15
embedded 0 27 A 0x6a 3 4 5 6 7 10 11 12 14 15
embedded 0 28 A 0x60 3 4 5 6 7 10 11 12 14 15
embedded 0 28 B 0x61 3 4 5 6 7 10 11 12 14 15
embedded 0 28 C 0x62 3 4 5 6 7 10 11 12 14 15
embedded 0 28 D 0x63 3 4 5 6 7 10 11 12 14 15
slot 32 4 0 A 0x60 3 4 5 6 7 10 11 12 14 15
slot 32 4 0 B 0x61 3 4 5 6 7 10 11 12 14 15
slot 32 4 0 C 0x62 3 4 5 6 7 10 11 12 14 15
slot 32 4 0 D 0x63 3 4 5 6 7 10 11 12 14 15
embedded 0 25 A 0x68 3 4 5 6 7 10 11 12 14 15
embedded 0 25 B 0x69 3 4 5 6 7 10 11 12 14 15
slot 1 5 0 A 0x69 3 4 5 6 7 10 11 12 14 15
slot 1 5 0 B 0x6a 3 4 5 6 7 10 11 12 14 15
slot 1 5 0 C 0x6b 3 4 5 6 7 10 11 12 14 15
slot 1 5 0 D 0x68 3 4 5 6 7 10 11 12 14 15
slot 2 5 1 A 0x6a 3 4 5 6 7 10 11 12 14 15
slot 2 5 1 B 0x6b 3 4 5 6 7 10 11 12 14 15
slot 2 5 1 C 0x68 3 4 5 6 7 10 11 12 14 15
slot 2 5 1 D 0x69 3 4 5 6 7 10 11 12 14 15
slot 3 5 2 A 0x6b 3 4 5 6 7 10 11 12 14 15
slot 3 5 2 B 0x68 3 4 5 6 7 10 11 12 14 15
slot 3 5 2 C 0x69 3 4 5 6 7 10 11 12 14 15
slot 3 5 2 D 0x6a 3 4 5 6 7 10 11 12 14 15
embedded 1 0 A 0x60 3 4 5 6 7 10 11 12 14 15
embedded 1 0 B 0x61 3 4 5 6 7 10 11 12 14 15
embedded 1 0 C 0x62 3 4 5 6 7 10 11 12 14 15
embedded 1 0 D 0x63 3 4 5 6 7 10 11 12 14 15
embedded 3 0 A 0x63 3 4 5 6 7 10 11 12 14 15
embedded 3 0 B 0x60 3 4 5 6 7 10 11 12 14 15
embedded 3 0 C 0x61 3 4 5 6 7 10 11 12 14 15
embedded 3 0 D 0x62 3 4 5 6 7 10 11 12 14 15
embedded 2 0 A 0x60 3 4 5 6 7 10 11 12 14 15
embedded 2 0 B 0x61 3 4 5 6 7 10 11 12 14 15
embedded 2 0 C 0x62 3 4 5 6 7 10 11 12 14 15
embedded 2 0 D 0x63 3 4 5 6 7 10 11 12 14 15
ACPI: RSDP @ 0x0xfa980/0x0014 (v 0 ACPIAM)
ACPI: RSDT @ 0x0xbbfa0000/0x0038 (v 1 A M I OEMRSDT 0x10000602 MSFT 0x00000097)
ACPI: FACP @ 0x0xbbfa0200/0x0084 (v 2 A M I OEMFACP 0x10000602 MSFT 0x00000097)
ACPI: DSDT @ 0x0xbbfa0440/0x8A38 (v 1 A0545 A0545000 0x00000000 INTL 0x20060113)
ACPI: FACS @ 0x0xbbfae000/0x0040
ACPI: APIC @ 0x0xbbfa0390/0x006C (v 1 A M I OEMAPIC 0x10000602 MSFT 0x00000097)
ACPI: MCFG @ 0x0xbbfa0400/0x003C (v 1 A M I OEMMCFG 0x10000602 MSFT 0x00000097)
ACPI: OEMB @ 0x0xbbfae040/0x007B (v 1 A M I AMI_OEM 0x10000602 MSFT 0x00000097)
ACPI: HPET @ 0x0xbbfa8e80/0x0038 (v 1 A M I OEMHPET 0x10000602 MSFT 0x00000097)
npx0.nexus0.root0
npx0: <math processor> [tentative] on motherboard
npx0: INT 16 interface
Using XMM optimized bcopy/copyin/copyout
npx0: <math processor> [attached!] on motherboard
acpi0.nexus0.root0
acpi0: <A M I OEMRSDT> [tentative] on motherboard
acpi0: Power Button (fixed)
Warning: ACPI is disabling APM's device. You can't run both
AcpiOsDerivePciId: bus 0 dev 0 func 0
AcpiOsDerivePciId: bus 0 dev 31 func 0
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
acpi_timer0.acpi0.nexus0.root0
acpi_timer0: <24-bit timer at 3.579545MHz> [tentative] port 0x808-0x80b on acpi0
acpi_timer0: <24-bit timer at 3.579545MHz> [attached!] port 0x808-0x80b on acpi0
cpu0.acpi0.nexus0.root0
cpu0: <ACPI CPU> [tentative] on acpi0
cpu0: <ACPI CPU> [attached!] on acpi0
acpi_button0.acpi0.nexus0.root0
acpi_button0: <Power Button> [tentative] on acpi0
acpi_button0: <Power Button> [attached!] on acpi0
unknown: not probed (disabled)
sio0: irq maps: 0 0x10 0 0
sio0.acpi0.nexus0.root0
sio0 [tentative] port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A
sio0 [attached!] port 0x3f8-0x3ff irq 4 on acpi0
unknown: not probed (disabled)
ppc0: using extended I/O port range
ppc0: ECP SPP ECP+EPP SPP
ppc0.acpi0.nexus0.root0
ppc0 [tentative] port 0x778-0x77f,0x378-0x37f irq 7 drq 3 on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/9 bytes threshold
ppbus0.ppc0.acpi0.nexus0.root0
ppbus0: <Parallel port bus> [tentative] on ppc0
plip0.ppbus0.ppc0.acpi0.nexus0.root0
plip0: <PLIP network interface> [tentative] on ppbus0
lp0: bpf attached
plip0: <PLIP network interface> [attached!] on ppbus0
lpt0.ppbus0.ppc0.acpi0.nexus0.root0
lpt0: <Printer> [tentative] on ppbus0
lpt0: Interrupt-driven port
lpt0: <Printer> [attached!] on ppbus0
ppi0.ppbus0.ppc0.acpi0.nexus0.root0
ppi0: <Parallel I/O> [tentative] on ppbus0
ppi0: <Parallel I/O> [attached!] on ppbus0
ppbus0: <Parallel port bus> [attached!] on ppc0
ppc0 [attached!] port 0x778-0x77f,0x378-0x37f irq 7 drq 3 on acpi0
atkbdc0.acpi0.nexus0.root0
atkbdc0: <Keyboard controller (i8042)> [tentative] port 0x64,0x60 irq 1 on acpi0
atkbd0.atkbdc0.acpi0.nexus0.root0
atkbd0: <AT Keyboard> [tentative] flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000
atkbd0: <AT Keyboard> [attached!] flags 0x1 irq 1 on atkbdc0
psm0: current command byte:0065
psm0: failed to reset the aux device.
atkbdc0: <Keyboard controller (i8042)> [attached!] port 0x64,0x60 irq 1 on acpi0
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
acpi0: <A M I OEMRSDT> [attached!] at irq 9 on motherboard
legacypci0.nexus0.root0
legacypci0 [tentative] on motherboard
pcib0.legacypci0.nexus0.root0
pcib0: <Host to PCI bridge> [tentative] on legacypci0
pci0.pcib0.legacypci0.nexus0.root0
pci0: <PCI bus> [tentative] on pcib0
pci0: pci_attach() physical bus=0
found-> vendor=0x8086, dev=0x29a0, revid=0x02
bus=0, slot=0, func=0
class=[BRIDGE]06-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
found-> vendor=0x8086, dev=0x29a1, revid=0x02
bus=0, slot=1, func=0
class=[BRIDGE]06-04-00, hdrtype=0x01, mfdev=0
subordinatebus=1 secondarybus=1
intpin=a, irq=11
PCI Express ver.1 cap=0x0141[ROOT], slotcap=0x00040000
map[20]: type 1, range 32, base 0000e000, size 5
found-> vendor=0x8086, dev=0x2834, revid=0x02
bus=0, slot=26, func=0
class=[SERIALBUS]0c-03-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
intpin=a, irq=11
map[20]: type 1, range 32, base 0000e080, size 5
found-> vendor=0x8086, dev=0x2835, revid=0x02
bus=0, slot=26, func=1
class=[SERIALBUS]0c-03-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=b, irq=5
map[10]: type 1, range 32, base febff400, size 10
found-> vendor=0x8086, dev=0x283a, revid=0x02
bus=0, slot=26, func=7
class=[SERIALBUS]0c-03-20, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=c, irq=15
found-> vendor=0x8086, dev=0x283f, revid=0x02
bus=0, slot=28, func=0
class=[BRIDGE]06-04-00, hdrtype=0x01, mfdev=1
subordinatebus=4 secondarybus=4
intpin=a, irq=11
PCI Express ver.1 cap=0x0141[ROOT], slotcap=0x00000060[HOTPLUG]
found-> vendor=0x8086, dev=0x2845, revid=0x02
bus=0, slot=28, func=3
class=[BRIDGE]06-04-00, hdrtype=0x01, mfdev=1
subordinatebus=3 secondarybus=3
intpin=d, irq=10
PCI Express ver.1 cap=0x0141[ROOT], slotcap=0x00000060[HOTPLUG]
found-> vendor=0x8086, dev=0x2847, revid=0x02
bus=0, slot=28, func=4
class=[BRIDGE]06-04-00, hdrtype=0x01, mfdev=1
subordinatebus=2 secondarybus=2
intpin=a, irq=11
PCI Express ver.1 cap=0x0141[ROOT], slotcap=0x00000060[HOTPLUG]
map[20]: type 1, range 32, base 0000d800, size 5
found-> vendor=0x8086, dev=0x2830, revid=0x02
bus=0, slot=29, func=0
class=[SERIALBUS]0c-03-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
intpin=a, irq=3
map[20]: type 1, range 32, base 0000d880, size 5
found-> vendor=0x8086, dev=0x2831, revid=0x02
bus=0, slot=29, func=1
class=[SERIALBUS]0c-03-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=b, irq=10
map[20]: type 1, range 32, base 0000dc00, size 5
found-> vendor=0x8086, dev=0x2832, revid=0x02
bus=0, slot=29, func=2
class=[SERIALBUS]0c-03-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=c, irq=15
map[10]: type 1, range 32, base febff000, size 10
found-> vendor=0x8086, dev=0x2836, revid=0x02
bus=0, slot=29, func=7
class=[SERIALBUS]0c-03-20, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=3
found-> vendor=0x8086, dev=0x244e, revid=0xf2
bus=0, slot=30, func=0
class=[BRIDGE]06-04-01, hdrtype=0x01, mfdev=0
subordinatebus=5 secondarybus=5
found-> vendor=0x8086, dev=0x2810, revid=0x02
bus=0, slot=31, func=0
class=[BRIDGE]06-01-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
map[10]: type 1, range 32, base 0000ec00, size 3
map[14]: type 1, range 32, base 0000e880, size 2
map[18]: type 1, range 32, base 0000e800, size 3
map[1c]: type 1, range 32, base 0000e480, size 2
map[20]: type 1, range 32, base 0000e400, size 5
map[24]: type 1, range 32, base febff800, size 11
found-> vendor=0x8086, dev=0x2824, revid=0x02
bus=0, slot=31, func=2
class=[STORAGE]01-06-01, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=b, irq=10
map[20]: type 1, range 32, base 00000400, size 5
found-> vendor=0x8086, dev=0x283e, revid=0x02
bus=0, slot=31, func=3
class=[SERIALBUS]0c-05-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=c, irq=10
pcib1.pci0.pcib0.legacypci0.nexus0.root0
pcib1: <PCI to PCI bridge (vendor=8086 device=29a1)> [tentative] irq 11 at device 1.0 on pci0
pcib1: secondary bus 1
pcib1: subordinate bus 1
pcib1: I/O decode 0xa000-0xafff
pcib1: memory decode 0xfa800000-0xfe8fffff
pcib1: prefetched decode 0xbfe00000-0xdfdfffff
pci1.pcib1.pci0.pcib0.legacypci0.nexus0.root0
pci1: <PCI bus> [tentative] on pcib1
pci1: pci_attach() physical bus=1
map[10]: type 1, range 32, base fd000000, size 24
map[14]: type 1, range 64, base c0000000, size 28
map[1c]: type 1, range 64, base fc000000, size 24
map[24]: type 1, range 32, base 0000ac00, size 7
found-> vendor=0x10de, dev=0x0393, revid=0xa1
bus=1, slot=0, func=0
class=[DISPLAY]03-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=11
PCI Express ver.1 cap=0x0001[DEVICE]
pci1: <NVidia model 0393 graphics accelerator> (vendor=0x10de, dev=0x0393) at 0.0 irq 11
pci1: <PCI bus> [attached!] on pcib1
pcib1: <PCI to PCI bridge (vendor=8086 device=29a1)> [attached!] irq 11 at device 1.0 on pci0
uhci0.pci0.pcib0.legacypci0.nexus0.root0
uhci0: <UHCI (generic) USB controller> [tentative] port 0xe000-0xe01f irq 11 at device 26.0 on pci0
usb0.uhci0.pci0.pcib0.legacypci0.nexus0.root0
usb0: <UHCI (generic) USB controller> [tentative] on uhci0
usb0: USB revision 1.0
uhub0.usb0.uhci0.pci0.pcib0.legacypci0.nexus0.root0
uhub0: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> [tentative] on usb0
uhub0: 2 ports with 2 removable, self powered
uhub0: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> [attached!] on usb0
usb0: <UHCI (generic) USB controller> [attached!] on uhci0
uhci0: <UHCI (generic) USB controller> [attached!] port 0xe000-0xe01f irq 11 at device 26.0 on pci0
uhci1.pci0.pcib0.legacypci0.nexus0.root0
uhci1: <UHCI (generic) USB controller> [tentative] port 0xe080-0xe09f irq 5 at device 26.1 on pci0
usb1.uhci1.pci0.pcib0.legacypci0.nexus0.root0
usb1: <UHCI (generic) USB controller> [tentative] on uhci1
usb1: USB revision 1.0
uhub1.usb1.uhci1.pci0.pcib0.legacypci0.nexus0.root0
uhub1: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> [tentative] on usb1
uhub1: 2 ports with 2 removable, self powered
uhub1: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> [attached!] on usb1
usb1: <UHCI (generic) USB controller> [attached!] on uhci1
uhci1: <UHCI (generic) USB controller> [attached!] port 0xe080-0xe09f irq 5 at device 26.1 on pci0
pci0: <USB controller> (vendor=0x8086, dev=0x283a) at 26.7 irq 15
pcib2.pci0.pcib0.legacypci0.nexus0.root0
pcib2: <PCI to PCI bridge (vendor=8086 device=283f)> [tentative] irq 11 at device 28.0 on pci0
pcib2: secondary bus 4
pcib2: subordinate bus 4
pcib2: I/O decode 0x0-0x0
pcib2: memory decode 0xfff00000-0xfffff
pcib2: prefetched decode 0xdfe00000-0xdfefffff
pci4.pcib2.pci0.pcib0.legacypci0.nexus0.root0
pci4: <PCI bus> [tentative] on pcib2
pci4: pci_attach() physical bus=4
pci4: <PCI bus> [attached!] on pcib2
pcib2: <PCI to PCI bridge (vendor=8086 device=283f)> [attached!] irq 11 at device 28.0 on pci0
pcib3.pci0.pcib0.legacypci0.nexus0.root0
pcib3: <PCI to PCI bridge (vendor=8086 device=2845)> [tentative] irq 10 at device 28.3 on pci0
pcib3: secondary bus 3
pcib3: subordinate bus 3
pcib3: I/O decode 0xc000-0xcfff
pcib3: memory decode 0xfea00000-0xfeafffff
pcib3: prefetched decode 0xfff00000-0xfffff
pci3.pcib3.pci0.pcib0.legacypci0.nexus0.root0
pci3: <PCI bus> [tentative] on pcib3
pci3: pci_attach() physical bus=3
map[10]: type 1, range 32, base 0000c800, size 8
map[18]: type 1, range 64, base feaff000, size 12
found-> vendor=0x10ec, dev=0x8168, revid=0x01
bus=3, slot=0, func=0
class=[NETWORK]02-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=10
PCI Express ver.1 cap=0x0001[DEVICE]
pcib3: device re0 requested decoded I/O range 0xc800-0xc8ff
re0.pci3.pcib3.pci0.pcib0.legacypci0.nexus0.root0
re0: <RealTek 8168/8111B PCIe Gigabit Ethernet> [tentative] port 0xc800-0xc8ff mem 0xfeaff000-0xfeafffff irq 10 at device 0.0 on pci3
pcib3: device re0 requested decoded I/O range 0xc800-0xc8ff
miibus0.re0.pci3.pcib3.pci0.pcib0.legacypci0.nexus0.root0
miibus0: <MII bus> [tentative] on re0
rgephy0: rev: 2
rgephy0.miibus0.re0.pci3.pcib3.pci0.pcib0.legacypci0.nexus0.root0
rgephy0: <8211B/RTL8169S/8110S media interface> [tentative] on miibus0
rgephy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
rgephy0: <8211B/RTL8169S/8110S media interface> [attached!] on miibus0
miibus0: <MII bus> [attached!] on re0
re0: bpf attached
re0: MAC address: 00:18:f3:09:1d:9c
re0: <RealTek 8168/8111B PCIe Gigabit Ethernet> [attached!] port 0xc800-0xc8ff mem 0xfeaff000-0xfeafffff irq 10 at device 0.0 on pci3
pci3: <PCI bus> [attached!] on pcib3
pcib3: <PCI to PCI bridge (vendor=8086 device=2845)> [attached!] irq 10 at device 28.3 on pci0
pcib4.pci0.pcib0.legacypci0.nexus0.root0
pcib4: <PCI to PCI bridge (vendor=8086 device=2847)> [tentative] irq 11 at device 28.4 on pci0
pcib4: secondary bus 2
pcib4: subordinate bus 2
pcib4: I/O decode 0xb000-0xbfff
pcib4: memory decode 0xfe900000-0xfe9fffff
pcib4: prefetched decode 0xfff00000-0xfffff
pci2.pcib4.pci0.pcib0.legacypci0.nexus0.root0
pci2: <PCI bus> [tentative] on pcib4
pci2: pci_attach() physical bus=2
map[24]: type 1, range 32, base fe9fe000, size 13
found-> vendor=0x197b, dev=0x2363, revid=0x02
bus=2, slot=0, func=0
class=[STORAGE]01-04-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
intpin=a, irq=11
PCI Express ver.1 cap=0x0211[LEGDEV]
map[10]: type 1, range 32, base 0000bc00, size 3
map[14]: type 1, range 32, base 0000b880, size 2
map[18]: type 1, range 32, base 0000b800, size 3
map[1c]: type 1, range 32, base 0000b480, size 2
map[20]: type 1, range 32, base 0000b400, size 4
found-> vendor=0x197b, dev=0x2363, revid=0x02
bus=2, slot=0, func=1
class=[STORAGE]01-01-85, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=b, irq=255
atapci0.pci2.pcib4.pci0.pcib0.legacypci0.nexus0.root0
atapci0: <JMicron JMB363 SATA300 controller> [tentative] mem 0xfe9fe000-0xfe9fffff irq 11 at device 0.0 on pci2
pcib4: device atapci0 requested decoded memory range 0xfe9fe000-0xfe9fffff
atapci0: AHCI called from vendor specific driver
atapci0: AHCI Version 01.00 controller with 2 ports detected
ata2.atapci0.pci2.pcib4.pci0.pcib0.legacypci0.nexus0.root0
ata2: <ATA channel 0> [tentative] on atapci0
ata2: SATA connect status=00000000
ata2: ahci_reset devices=0x0
ata2: <ATA channel 0> [attached!] on atapci0
ata3.atapci0.pci2.pcib4.pci0.pcib0.legacypci0.nexus0.root0
ata3: <ATA channel 1> [tentative] on atapci0
ata3: SATA connect status=00000000
ata3: ahci_reset devices=0x0
ata3: <ATA channel 1> [attached!] on atapci0
atapci0: <JMicron JMB363 SATA300 controller> [attached!] mem 0xfe9fe000-0xfe9fffff irq 11 at device 0.0 on pci2
atapci1.pci2.pcib4.pci0.pcib0.legacypci0.nexus0.root0
atapci1: <JMicron JMB363 UDMA133 controller> [tentative] port 0xb400-0xb40f,0xb480-0xb483,0xb800-0xb807,0xb880-0xb883,0xbc00-0xbc07 at device 0.1 on pci2
pcib4: device atapci1 requested decoded I/O range 0xb400-0xb40f
pci_cfgintr_valid: BIOS irq 11 is valid
pci_cfgintr: 0:28 INTB BIOS irq 11
pcib4: routed slot 0 INTB to irq 11
ata4.atapci1.pci2.pcib4.pci0.pcib0.legacypci0.nexus0.root0
ata4: <ATA channel 0> [tentative] on atapci1
pcib4: device atapci1 requested decoded I/O range 0xbc00-0xbc07
pcib4: device atapci1 requested decoded I/O range 0xb880-0xb883
ata4: reset tp1 mask=03 ostat0=50 ostat1=00
ata4: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata4: stat1=0x00 err=0x01 lsb=0x00 msb=0x00
ata4: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
intr 5 at 40001/40000 hz, livelocked limit engaged!
intr 5 at 46034/20000 hz, in livelock
ata4: reiniting channel ..
ata4: reset tp1 mask=03 ostat0=58 ostat1=00
ata4: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata4: stat1=0x00 err=0x01 lsb=0x00 msb=0x00
ata4: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata4: reinit done ..
intr 5 at 3843/20000 hz, livelock removed
intr 5 at 40001/40000 hz, livelocked limit engaged!
intr 5 at 47000/20000 hz, in livelock
ata4: reiniting channel ..
ata4: reset tp1 mask=03 ostat0=58 ostat1=00
ata4: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata4: stat1=0x00 err=0x01 lsb=0x00 msb=0x00
ata4: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata4: reinit done ..
ata4: <ATA channel 0> [attached!] on atapci1
atapci1: <JMicron JMB363 UDMA133 controller> [attached!] port 0xb400-0xb40f,0xb480-0xb483,0xb800-0xb807,0xb880-0xb883,0xbc00-0xbc07 irq 11 at device 0.1 on pci2
pci2: <PCI bus> [attached!] on pcib4
pcib4: <PCI to PCI bridge (vendor=8086 device=2847)> [attached!] irq 11 at device 28.4 on pci0
uhci2.pci0.pcib0.legacypci0.nexus0.root0
uhci2: <UHCI (generic) USB controller> [tentative] port 0xd800-0xd81f irq 3 at device 29.0 on pci0
usb2.uhci2.pci0.pcib0.legacypci0.nexus0.root0
usb2: <UHCI (generic) USB controller> [tentative] on uhci2
usb2: USB revision 1.0
uhub2.usb2.uhci2.pci0.pcib0.legacypci0.nexus0.root0
uhub2: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> [tentative] on usb2
uhub2: 2 ports with 2 removable, self powered
uhub2: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> [attached!] on usb2
usb2: <UHCI (generic) USB controller> [attached!] on uhci2
uhci2: <UHCI (generic) USB controller> [attached!] port 0xd800-0xd81f irq 3 at device 29.0 on pci0
uhci3.pci0.pcib0.legacypci0.nexus0.root0
uhci3: <UHCI (generic) USB controller> [tentative] port 0xd880-0xd89f irq 10 at device 29.1 on pci0
usb3.uhci3.pci0.pcib0.legacypci0.nexus0.root0
usb3: <UHCI (generic) USB controller> [tentative] on uhci3
usb3: USB revision 1.0
uhub3.usb3.uhci3.pci0.pcib0.legacypci0.nexus0.root0
uhub3: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> [tentative] on usb3
uhub3: 2 ports with 2 removable, self powered
uhub3: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> [attached!] on usb3
usb3: <UHCI (generic) USB controller> [attached!] on uhci3
uhci3: <UHCI (generic) USB controller> [attached!] port 0xd880-0xd89f irq 10 at device 29.1 on pci0
uhci4.pci0.pcib0.legacypci0.nexus0.root0
uhci4: <UHCI (generic) USB controller> [tentative] port 0xdc00-0xdc1f irq 15 at device 29.2 on pci0
usb4.uhci4.pci0.pcib0.legacypci0.nexus0.root0
usb4: <UHCI (generic) USB controller> [tentative] on uhci4
usb4: USB revision 1.0
uhub4.usb4.uhci4.pci0.pcib0.legacypci0.nexus0.root0
uhub4: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> [tentative] on usb4
uhub4: 2 ports with 2 removable, self powered
uhub4: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> [attached!] on usb4
usb4: <UHCI (generic) USB controller> [attached!] on uhci4
uhci4: <UHCI (generic) USB controller> [attached!] port 0xdc00-0xdc1f irq 15 at device 29.2 on pci0
pci0: <USB controller> (vendor=0x8086, dev=0x2836) at 29.7 irq 3
pcib5.pci0.pcib0.legacypci0.nexus0.root0
pcib5: <Intel 82801BA/CA/DB/EB/FB (ICH2/3/4/5/6) Hub to PCI bridge> [tentative] at device 30.0 on pci0
pcib5: secondary bus 5
pcib5: subordinate bus 5
pcib5: I/O decode 0xf000-0xfff
pcib5: memory decode 0x0-0x0
pcib5: prefetched decode 0x0-0x0
pcib5: Subtractively decoded bridge.
pci5.pcib5.pci0.pcib0.legacypci0.nexus0.root0
pci5: <PCI bus> [tentative] on pcib5
pci5: pci_attach() physical bus=5
pci5: <PCI bus> [attached!] on pcib5
pcib5: <Intel 82801BA/CA/DB/EB/FB (ICH2/3/4/5/6) Hub to PCI bridge> [attached!] at device 30.0 on pci0
isab0.pci0.pcib0.legacypci0.nexus0.root0
isab0: <PCI to ISA bridge (vendor=8086 device=2810)> [tentative] at device 31.0 on pci0
isa0.isab0.pci0.pcib0.legacypci0.nexus0.root0
isa0: <ISA bus> [tentative] on isab0
isa0: <ISA bus> [attached!] on isab0
isab0: <PCI to ISA bridge (vendor=8086 device=2810)> [attached!] at device 31.0 on pci0
atapci2.pci0.pcib0.legacypci0.nexus0.root0
atapci2: <Intel (ID=28248086) AHCI controller> [tentative] port 0xe400-0xe41f,0xe480-0xe483,0xe800-0xe807,0xe880-0xe883,0xec00-0xec07 mem 0xfebff800-0xfebfffff irq 10 at device 31.2 on pci0
atapci2: AHCI Version 01.10 controller with 4 ports detected
ata5.atapci2.pci0.pcib0.legacypci0.nexus0.root0
ata5: <ATA channel 0> [tentative] on atapci2
ata5: SATA connect status=00000000
ata5: ahci_reset devices=0x0
ata5: <ATA channel 0> [attached!] on atapci2
ata6.atapci2.pci0.pcib0.legacypci0.nexus0.root0
ata6: <ATA channel 1> [tentative] on atapci2
intr 10 at 40001/40000 hz, livelocked limit engaged!
ata6: executing CLO failed
ata6: SATA connect time=0ms
ata6: ahci_reset devices=0x1<ATA_MASTER>
intr 5 at 3820/20000 hz, livelock removed
intr 10 at 40001/20000 hz, in livelock
intr 10 at 3/20000 hz, livelock removed
ata6-master: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=40 wire
ad12: Intel check1 failed
ad12: Adaptec check1 failed
ad12: LSI (v3) check1 failed
ad12: LSI (v2) check1 failed
ad12: FreeBSD check1 failed
ad12: 238475MB <Seagate ST3250823AS 3.02> at ata6-master SATA150
ad12: 488397168 sectors [484521C/16H/63S] 16 sectors/interrupt 1 depth queue
ata6: <ATA channel 1> [attached!] on atapci2
ata7.atapci2.pci0.pcib0.legacypci0.nexus0.root0
ata7: <ATA channel 2> [tentative] on atapci2
ata7: port not implemented
ata7: <ATA channel 2> [attached!] on atapci2
ata8.atapci2.pci0.pcib0.legacypci0.nexus0.root0
ata8: <ATA channel 3> [tentative] on atapci2
ata8: port not implemented
ata8: <ATA channel 3> [attached!] on atapci2
ata9.atapci2.pci0.pcib0.legacypci0.nexus0.root0
ata9: <ATA channel 4> [tentative] on atapci2
ata9: SATA connect status=00000000
ata9: ahci_reset devices=0x0
ata9: <ATA channel 4> [attached!] on atapci2
ata10.atapci2.pci0.pcib0.legacypci0.nexus0.root0
ata10: <ATA channel 5> [tentative] on atapci2
intr 10 at 40001/40000 hz, livelocked limit engaged!
ata10: executing CLO failed
ata10: SATA connect time=0ms
ata10: ahci_reset devices=0x1<ATA_MASTER>
intr 10 at 40001/20000 hz, in livelock
ata10-master: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=40 wire
ad20: Intel check1 failed
ad20: Adaptec check1 failed
ad20: LSI (v3) check1 failed
ad20: LSI (v2) check1 failed
ad20: FreeBSD check1 failed
ad20: 238475MB <Seagate ST3250823AS 3.02> at ata10-master SATA150
ad20: 488397168 sectors [484521C/16H/63S] 16 sectors/interrupt 1 depth queue
ata10: <ATA channel 5> [attached!] on atapci2
atapci2: <Intel (ID=28248086) AHCI controller> [attached!] port 0xe400-0xe41f,0xe480-0xe483,0xe800-0xe807,0xe880-0xe883,0xec00-0xec07 mem 0xfebff800-0xfebfffff irq 10 at device 31.2 on pci0
pci0: <unknown card> (vendor=0x8086, dev=0x283e) at 31.3 irq 10
pci0: <PCI bus> [attached!] on pcib0
pcib0: <Host to PCI bridge> [attached!] on legacypci0
legacypci0 [attached!] on motherboard
ex_isa_identify()
ahc_isa_probe 11: ioport 0xbc00 alloc failed
ahc_isa_probe 13: ioport 0xdc00 alloc failed
atkbdc-: atkbdc0 exists, using next available unit number
sio-: sio0 exists, using next available unit number
sio-: sio1 exists, using next available unit number
sio-: sio2 exists, using next available unit number
sio-: sio3 exists, using next available unit number
ppc-: ppc0 exists, using next available unit number
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0.isa0.isab0.pci0.pcib0.legacypci0.nexus0.root0
orm0: <Option ROM> [tentative] at iomem 0xd0800-0xd17ff on isa0
orm0: <Option ROM> [attached!] at iomem 0xd0800-0xd17ff on isa0
pmtimer0.isa0.isab0.pci0.pcib0.legacypci0.nexus0.root0
pmtimer0 [tentative] on isa0
pmtimer0 [attached!] on isa0
fdc0: ready for input in output
fdc0: cmd 3 failed at out byte 1 of 3
fdc0 [tentative] failed to probe at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
adv0 [tentative] failed to probe on isa0
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x330
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x334
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x230
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x234
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x130
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x134
bt0 [tentative] failed to probe at port 0x134-0x137 on isa0
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0 [tentative] failed to probe at port 0x134-0x137 on isa0
aic0 [tentative] failed to probe at port 0x140-0x15f on isa0
atkbdc1: <Keyboard controller (i8042)> [tentative] failed to probe at port 0x60 on isa0
vga0.isa0.isab0.pci0.pcib0.legacypci0.nexus0.root0
vga0: <Generic ISA VGA> [tentative] at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 54 80
bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 54 80
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 54 80
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
vga0: <Generic ISA VGA> [attached!] at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0.isa0.isab0.pci0.pcib0.legacypci0.nexus0.root0
sc0: <System console> [tentative] at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sc0: <System console> [attached!] at flags 0x100 on isa0
lm0 [tentative] failed to probe at port 0x290 on isa0
it0 [tentative] failed to probe at port 0x290 on isa0
it1 [tentative] failed to probe at port 0xc00-0xc07 on isa0
it2 [tentative] failed to probe at port 0xd00-0xd07 on isa0
sio1 [tentative] failed to probe at port 0x3f8 irq 4 flags 0x10 on isa0
sio2: can't drain, serial port might not exist, disabling
sio2 [tentative] failed to probe at port 0x2f8-0x2ff irq 3 on isa0
sio3: not probed (disabled)
sio4: not probed (disabled)
ppc1: parallel port found at 0x378
ppc1: cannot reserve I/O port range
ppc1: <Parallel port> [tentative] failed to probe at port 0x378-0x37f irq 7 on isa0
ed0: not probed (disabled)
fe0: not probed (disabled)
ie0: not probed (disabled)
lnc0: not probed (disabled)
cs0: not probed (disabled)
sn0: not probed (disabled)
isa_probe_children: probing PnP devices
BIOS Geometries:
0:03fffe3f 0..1023=1024 cylinders, 0..254=255 heads, 1..63=63 sectors
1:03fefe3f 0..1022=1023 cylinders, 0..254=255 heads, 1..63=63 sectors
2:03fefe3f 0..1022=1023 cylinders, 0..254=255 heads, 1..63=63 sectors
0 accounted for
Device configuration finished.
intr 10 at 19/20000 hz, livelock removed
lo0: bpf attached
ppp0: bpf attached
crypto: assign driver 0, flags 2
crypto: driver 0 registers alg 1 flags 0 maxoplen 0
crypto: driver 0 registers alg 2 flags 0 maxoplen 0
crypto: driver 0 registers alg 3 flags 0 maxoplen 0
crypto: driver 0 registers alg 4 flags 0 maxoplen 0
crypto: driver 0 registers alg 5 flags 0 maxoplen 0
crypto: driver 0 registers alg 17 flags 0 maxoplen 0
crypto: driver 0 registers alg 6 flags 0 maxoplen 0
crypto: driver 0 registers alg 7 flags 0 maxoplen 0
crypto: driver 0 registers alg 15 flags 0 maxoplen 0
crypto: driver 0 registers alg 8 flags 0 maxoplen 0
crypto: driver 0 registers alg 16 flags 0 maxoplen 0
crypto: driver 0 registers alg 9 flags 0 maxoplen 0
crypto: driver 0 registers alg 10 flags 0 maxoplen 0
crypto: driver 0 registers alg 13 flags 0 maxoplen 0
crypto: driver 0 registers alg 14 flags 0 maxoplen 0
crypto: driver 0 registers alg 11 flags 0 maxoplen 0
crypto: driver 0 registers alg 18 flags 0 maxoplen 0
sl0: bpf attached
faith0: bpf attached
ATA PseudoRAID loaded
Mounting root from cd9660:/dev/acd0a
no disk named 'acd0a'
setrootbyname failed
iso_mountroot: can't find rootvp
Root mount failed: 6
Mounting root from nfs:
nfs_mountroot: interface re0 ip 10.1.0.254 bcast 10.1.0.255 mask 255.255.255.0
NFS_ROOT: 10.1.0.1:/
start_init: trying /sbin/init
More information about the Bugs
mailing list