[issue558] ACPI and IRQ problems
Chris Turner
c.turner at 199technologies.org
Wed Feb 14 18:52:11 PST 2007
DISCLAIMER: not sure if portions of this are 100% related .. but
on my system(s), I am:
- trying to hack in support for a no-name pci-to-cbb device from
vendor 'SYBA',which appears to be a repacaged Ricoh RL4C475
differing in the vendor id, which shows up on 1.8.0 via
`pciconf -vl` as::
none2 at pci0:16:0: class=0x066300 card=0x00000000
chip=0x04750001 rev=0x63 hdr=0x02
(see attached diff fer the 'deets of my adventures in
/usr/src/sys/dev/pccard/pccbb-land ... not sure if anyone
would want a pci vendor == 0x0001 device in-tree, but if anyone
snags one of these gismos, a diff might be useful :)
- first reboot after applied diff yielded::
cbb0: <RF5C475 PCI-CardBus Bridge> irq 127 at device 16.0 on pci0
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
cbb: Unable to map IRQ...
device_probe_and_attach: cbb0 attach returned 12
the 'irq 127' seemed a bit odd (much as '255' in your dmesg)
so I tried:
- rebooting again with acpi enabled (on a dot-com boomin'
PII i440BX chipset), which yielded a pre-POST bios-level irq conflict.
- rebooted yet again, entered bios and disabled local lpt / 1284 /
printer port, and:
- rebooted again w/o ACPI, resulting in many
"sched_ithd: stray interrupt 7" messages - appearing to make
ye-olde kernel enter an endless?? interrupt handling loop
see also:
http://leaf.dragonflybsd.org/mailarchive/users/2006-11/msg00274.html
although this particular kernel is UP..
- rebooted with acpi enabled.. this time, cbb seemed to attach as
follows::
cbb0: <RF5C475 PCI-CardBus Bridge> at device 16.0 on pci0
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
thinking I'd made the SYBA cbb0 work, I tried to test my loaner
verizin wharless PC5740 cdma card, to no avail::
cardbus0: Resource not specified in CIS: id=10, size=1000
cardbus0: <unknown card> (vendor=0x0000, dev=0x0000) at 0.0
cbb0: CardBus card activation failed
cardbus0: Resource not specified in CIS: id=10, size=1000
ohci0: <NEC uPD 9210 USB controller> mem 0x88001000-0x88001fff irq 3
at device 0.0 on cardbus0
usb1: OHCI version 15.15, legacy support
usb1: unsupported OHCI revision
ohci0: USB init failed
device_probe_and_attach: ohci0 attach returned 5
unfortunately, as this is the only pcmcia/cardbus card I have A.T.M,
I have no idea as to whether my hacked driver is borked or if the
cdma card isn't quite working properly.. and would prefer to know
this before I try to tackle something with OHCI v15.15??..
So, I decided to:
- boot up my laptop (ferrari 1000)
- and try the card.
- recieved the same errors about the PCcard not working on insert
time, making me a tad-more confident about the SYBA cbb hack..
what is interesting is that on the F1000:
- issue #387,
http://leaf.dragonflybsd.org/mailarchive/bugs/2006-11/msg00060.html
is also apparent (has bge0)
- I am getting the same "sched_ithd: stray interrupt 7" errors,
but not in the endless-loop?? mentioned above, and the PII box has
-never- (since 1.4.x) had the stray interrupt errors until the cbb
was added
- the F1000 has an EHCI interface, related to 'stray interrupt 7' errors
here::
http://leaf.dragonflybsd.org/mailarchive/users/2006-09/msg00094.html
I've not yet tried any usb devices on it..
- when APIC_IO is enabled as mentioned in #387, bge gets the #387
timeouts, a higher frequency of 'stray interrupts' are apparent,
and one cpu is near-totally consumed (according to top(1)).
When APIC_IO is disabled, both cores / CPU's idle as expected and
bge0 works fine, with less 'stray interrupt 7' errors..
- acpi was "better" than no-acpi on the F100, for reasons I can't
quite remember.
I understand based on the discussion of one-or-another of the issues
relating to ACPI that possibly interrupt routing might take a bit
of work to get sorted out..
but perhaps a few drivers / bioses / options are making this worse.
cbb, bge, lpt, APIC_IO, SMP, radeon? on recent dual core (laptop?)
models come to mind here..
Also, I recall in the near-to-1.8 release list threads, someone having
trouble with a IBM core-2 laptop conflagaration overheating -
perhaps the CPU usage I saw related to having APIC_IO enabled might
resolve this for that person...
having trouble finding chipset info on the F1000 at the moment, based on
http://www.trustedreviews.com/notebooks/review/2006/08/16/Acer-Ferrari-1000/p4
this appears to be a Radeon Xpress 1150 .. which I thought was just the
Grapics chip.. but anyhow.
also-possibly-related:
http://lists.freebsd.org/pipermail/freebsd-current/2004-February/021941.html
(mentions apics and interrupt 7s)
in any case, just a ton of disorganized and possibly worthless data
points I suppose.. and my kernel newbness doesn't help understainding
how interrupt routing works.. sigh..
n.e. way: mostly off topic and last-but-not-least:
My F1000 has what appears to be a bcw(OpenBSD4) wifi chip...
see also:
http://www.openbsd.org/cgi-bin/man.cgi?query=bcw&sektion=4&format=html
thinking of attempting the port, unless anyone else is working on it...
anyone?
sorry for the disorganization of this post / relavence to initial
issue.. but as often, when the details are vague,
things are tougher to sift through.
Thanks again for DragonFly!
- Chris
Alexey Slynko wrote:
> New submission from Alexey Slynko <slynko at tronet.ru>:
>
> Hi,
>
> still have the same ACPI and IRQ problems on HEAD. ichsmb, cardbus and one usb
> port doesn't work properly. Here is demsg messages below
>
> Copyright (c) 2003, 2004, 2005, 2006, 2007 The DragonFly Project.
> Copyright (c) 1992-2003 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
> The Regents of the University of California. All rights reserved.
> DragonFly 1.9.0-DEVELOPMENT #0: Wed Feb 14 15:34:06 MSK 2007
> root at elizabet.tronet.ru:/usr/obj/usr/src/sys/ELIZABET
> TSC clock: 1690227876 Hz, i8254 clock: 1193179 Hz
> CPU: Mobile Intel(R) Celeron(R) CPU 1.70GHz (1690.24-MHz 686-class CPU)
> Origin = "GenuineIntel" Id = 0xf27 Stepping = 7
>
> Features=0xbfebf9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
> Features2=0x400<CNTX-ID>
> real memory = 134217728 (131072K bytes)
> avail memory = 122286080 (119420K bytes)
> Preloaded elf kernel "/kernel" at 0xc056b000.
> Preloaded elf module "/modules/vesa.ko" at 0xc056b288.
> Preloaded elf module "/modules/if_ath.ko" at 0xc056b330.
> ath_hal: 0.9.16.16 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
> link_elf: symbol ieee80211_iterate_nodes undefined
> link_elf_load_file: cannot load 'ath_rate' from filesystem this early
> Preloaded elf module "/modules/wlan.ko" at 0xc056b3d8.
> Preloaded elf module "/modules/snd_ich.ko" at 0xc056b5d4.
> Preloaded elf module "/modules/sound.ko" at 0xc056b67c.
> Preloaded elf module "/modules/usb.ko" at 0xc056b724.
> Preloaded elf module "/modules/ums.ko" at 0xc056b7c8.
> Preloaded elf module "/modules/radeon.ko" at 0xc056b86c.
> Preloaded elf module "/modules/acpi.ko" at 0xc056b914.
> netsmb_dev: loaded
> Pentium Pro MTRR support enabled
> md0: Malloc disk
> pcibios: BIOS version 2.10
> Using $PIR table, 7 entries at 0xc00fdf50
> ACPI: RSDP @ 0x0xf7400/0x0014 (v 0 PTLTD )
> ACPI: RSDT @ 0x0xfefa5dc/0x0030 (v 1 SONY B0 0x20021203 PTL 0x00000000)
> ACPI: FACP @ 0x0xfefee7d/0x0074 (v 1 SONY B0 0x20021203 PTL 0x01000000)
> ACPI: DSDT @ 0x0xfefa60c/0x4871 (v 1 SONY B0 0x20021203 PTL 0x0100000D)
> ACPI: FACS @ 0x0xfefffc0/0x0040
> ACPI: BOOT @ 0x0xfefeef1/0x0028 (v 1 SONY B0 0x20021203 PTL 0x00000001)
> ACPI: SSDT @ 0x0xfefef19/0x00E7 (v 1 SONY B0 0x20021203 PTL 0x00000001)
> npx0: <math processor> on motherboard
> npx0: INT 16 interface
> Using XMM optimized bcopy/copyin/copyout
> acpi0: <SONY> on motherboard
> Warning: ACPI is disabling APM's device. You can't run both
> can't fetch resources for \\_PR_.CPU0 - AE_TYPE
> can't fetch resources for \\_TZ_.ATF0 - AE_TYPE
> acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
> ACPI Error (evregion-0427): No handler for Region [ECR_] (0xc0c92578)
> [EmbeddedControl] [20061109]
> ACPI Error (exfldio-0390): Region EmbeddedControl(3) has no handler [20061109]
> ACPI Error (psparse-0638): Method parse/execution failed [\\_PR_.CPU0._CST]
> (Node 0xc0c70b40), AE_NOT_EXIST
> cpu0: <ACPI CPU (2 Cx states)> on acpi0
> ACPI Error (evregion-0427): No handler for Region [ECR_] (0xc0c92578)
> [EmbeddedControl] [20061109]
> ACPI Error (exfldio-0390): Region EmbeddedControl(3) has no handler [20061109]
> ACPI Error (psparse-0638): Method parse/execution failed [\\_PR_.CPU0._CST]
> (Node 0xc0c70b40), AE_NOT_EXIST
> acpi_tz0: <Thermal Zone> on acpi0
> acpi_lid0: <Control Method Lid Switch> on acpi0
> acpi_button0: <Power Button> on acpi0
> acpi_ec0: <Embedded Controller: GPE 0x1c> port 0x66,0x62 on acpi0
> acpi_cmbat0: <Control Method Battery> on acpi0
> acpi_cmbat1: <Control Method Battery> on acpi0
> acpi_acad0: <AC Adapter> on acpi0
> legacypci0 on motherboard
> pcib0: <Intel 82845 Host to PCI bridge> on legacypci0
> pci0: <PCI bus> on pcib0
> agp0: <Intel 82845 host to AGP bridge> mem 0xec000000-0xefffffff at device 0.0
> on pci0
> pcib1: <Intel 82845 PCI-PCI (AGP) bridge> at device 1.0 on pci0
> pci1: <PCI bus> on pcib1
> drm0: <ATI Radeon LW Mobility 7500 M7> port 0x3000-0x30ff mem
> 0xe8100000-0xe810ffff,0xf0000000-0xf7ffffff irq 9 at device 0.0 on pci1
> info: [drm] AGP at 0xec000000 64MB
> info: [drm] Initialized radeon 1.8.0 20020828 on minor 0
> uhci0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> port 0x1800-0x181f irq 9
> at device 29.0 on pci0
> usb0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> on uhci0
> usb0: USB revision 1.0
> uhub0: 2 ports with 2 removable, self powered
> uhci1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> port 0x1820-0x183f irq 9
> at device 29.1 on pci0
> usb1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> on uhci1
> usb1: USB revision 1.0
> uhub1: 2 ports with 2 removable, self powered
> intr 9 at 50001 > 50000 hz, livelocked limit engaged!
> ums0: Logitech USB RECEIVER, rev 1.10/25.10, addr 2, iclass 3/1
> ums0: 16 buttons and Z dir.
> uhci2: <Intel 82801CA/CAM (ICH3) USB controller USB-C> port 0x1840-0x185f at
> device 29.2 on pci0
> uhci2: Could not allocate irq
> device_probe_and_attach: uhci2 attach returned 6
> pcib2: <PCI to PCI bridge (vendor=8086 device=2448)> at device 30.0 on pci0
> pci2: <PCI bus> on pcib2
> cbb0: <RF5C476 PCI-CardBus Bridge> irq 3 at device 5.0 on pci2
> cardbus0: <CardBus bus> on cbb0
> pccard0: <16-bit PCCard bus> on cbb0
> cbb1: <RF5C476 PCI-CardBus Bridge> at device 5.1 on pci2
> cardbus1: <CardBus bus> on cbb1
> pccard1: <16-bit PCCard bus> on cbb1
> pcib2: routed slot 5 INTB to irq 255
> cbb: Unable to map IRQ...
> device_probe_and_attach: cbb1 attach returned 12
> pci2: <unknown card> (vendor=0x1180, dev=0x0552) at 5.2
> fxp0: <Intel 82801CAM (ICH3) Pro/100 VE Ethernet> port 0x4000-0x403f mem
> 0xe8200000-0xe8200fff irq 9 at device 8.0 on pci2
> miibus0: <MII bus> on fxp0
> inphy0: <i82562ET 10/100 media interface> on miibus0
> inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> fxp0: MAC address: 08:00:46:68:73:0a
> isab0: <PCI to ISA bridge (vendor=8086 device=248c)> at device 31.0 on pci0
> isa0: <ISA bus> on isab0
> atapci0: <Intel ICH3 ATA100 controller> port
> 0x1860-0x186f,0x374-0x377,0x170-0x177,0x3f4-0x3f7,0x1f0-0x1f7 at device 31.1 on pci0
> ata0: at 0x1f0 irq 14 on atapci0
> ata1: at 0x170 irq 15 on atapci0
> ichsmb0: <Intel 82801CA (ICH3) SMBus controller> port 0x1880-0x189f at device
> 31.3 on pci0
> device_probe_and_attach: ichsmb0 attach returned 6
> pcm0: <Intel ICH3 (82801CA)> port 0x18c0-0x18ff,0x1c00-0x1cff irq 9 at device
> 31.5 on pci0
> pcm0: <Yamaha YMF753 AC97 Codec>
> pci0: <unknown card> (vendor=0x8086, dev=0x2486) at 31.6
> orm0: <Option ROMs> at iomem 0xc0000-0xcffff,0xd8000-0xdbfff,0xdc000-0xdffff on isa0
> pmtimer0 on isa0
> fdc0: ready for input in output
> fdc0: cmd 3 failed at out byte 1 of 3
> atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
> atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
> kbd0 at atkbd0
> psm0: <PS/2 Mouse> irq 12 on atkbdc0
> psm0: model Generic PS/2 mouse, device ID 0
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
> sc0: <System console> at flags 0x100 on isa0
> sc0: VGA <16 virtual consoles, flags=0x300>
> sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
> sio0: type 16550A
> sio1: can't drain, serial port might not exist, disabling
> ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
> ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
> ppc0: FIFO with 16/16/15 bytes threshold
> ppbus0: <Parallel port bus> on ppc0
> plip0: <PLIP network interface> on ppbus0
> lpt0: <Printer> on ppbus0
> lpt0: Interrupt-driven port
> ppi0: <Parallel I/O> on ppbus0
> IP packet filtering initialized, divert enabled, rule-based forwarding enabled,
> default to deny, logging disabled
> ata1-slave: ATAPI identify retries exceeded
> acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0%
> cbb0: CardBus card activation failed
> ad0: 76319MB <HTS548080M9AT00> [155061/16/63] at ata0-master UDMA100
> acd0: CD-RW <UJDA740 DVD/CDRW> at ata1-master PIO4
> cd0 at ata1 bus 0 target 0 lun 0
> cd0: <MATSHITA UJDA740 DVD/CDRW 1.00> Removable CD-ROM SCSI-0 device
> cd0: 16.000MB/s transfers
> cd0: Attempt to query device size failed: NOT READY, Medium not present
> Mounting root from ufs:/dev/ad0s4a
> intr 9 at 7376 < 20000 hz, livelock removed
>
>
> All this devices works properly on FreeBSD since 5.x
> I'm ready for testing patches, and may be somebody can tell me about the part of
> source tree, which is responcible for this functionality
>
> ----------
> messages: 2277
> nosy: slynko
> priority: bug
> status: unread
> superseder: IRQ problems
> title: ACPI and IRQ problems
> topic: acpi
>
> _____________________________________________________
> DragonFly issue tracker <bugs at lists.dragonflybsd.org>
> <http://bugs.dragonflybsd.org/issue558>
> _____________________________________________________
>
Index: pccbb/pccbb.c
===================================================================
RCS file: /nbsd/dcvs/src/sys/dev/pccard/pccbb/pccbb.c,v
retrieving revision 1.19
diff -r1.19 pccbb.c
156a157
> {PCIC_ID_SYBA_RL5C475, "RF5C475 PCI-CardBus Bridge", CB_RF5C47X},
Index: pccbb/pccbbdevid.h
===================================================================
RCS file: /nbsd/dcvs/src/sys/dev/pccard/pccbb/pccbbdevid.h,v
retrieving revision 1.1
diff -r1.1 pccbbdevid.h
47a48
> #define PCIC_ID_SYBA_RL5C475 0x04750001ul
More information about the Bugs
mailing list