dmesg troubleshooting

Sepherosa Ziehau sepherosa at gmail.com
Sun Apr 23 18:55:50 PDT 2017


Hmm, the Realtek interface is the cause of the interrupt storm.  So
the timer probably is not working.  Try following:
sysctl net.ifpoll.0.pollhz=1000
sysctl net.ifpoll.1.pollhz=1000
ifconfig re0 polling

Thanks,
sephe


On Thu, Apr 20, 2017 at 11:18 PM, Predrag Punosevac
<punosevac72 at gmail.com> wrote:
> Sepherosa Ziehau <sepherosa at gmail.com> wrote:
>
>> Can you post the dmesg and vmstat -iv?  I think for ahci controller,
>> MSI will be used by default.
>
> dfly# vmstat -iv
> interrupt                                total       rate
> irq1     0: atkbd0                           1          0
> irq3     0: sio1                             0          0
> irq4     0: sio0                             0          0
> irq9     0: acpi0                            0          0
> irq11    0: ehci0/ehci1                 274707          1
> irq16    0: re0                         168712          1
> irq192   0: swi_siopoll                      0          0
> irq196   0: swi_vm                           0          0
> irq16    1: ahci0                      1495360          9
> irq195   1: swi_cambio                  752050          4
> irq197   1: swi_mp_taskq/swi_taskq           0          0
> Total                                  2690830         17
>
>
>
>
>
>
> Copyright (c) 2003-2017 The DragonFly Project.
> Copyright (c) 1992-2003 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
>         The Regents of the University of California. All rights reserved.
> DragonFly v4.8.0.1.g86163-RELEASE #4: Tue Mar 28 07:56:27 EST 2017
>     root at dfly.bagdala2.net:/usr/obj/usr/src/sys/X86_64_GENERIC
> i8254 clock: 1193296 Hz
> TSC invariant clock: 1795934280 Hz
> CPU: Intel(R) Celeron(R) CPU 1037U @ 1.80GHz (1795.93-MHz K8-class CPU)
>   Origin = "GenuineIntel"  Id = 0x306a9  Stepping = 9
>   Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
>   Features2=0x5bae3bf<SSE3,PCLMULQDQ,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,POPCNT,TSCDLT,XSAVE>
>   AMD Features=0x28100800<SYSCALL,NX,RDTSCP,LM>
>   AMD Features2=0x1<LAHF>
>   Structured Extended Features=0x281<GSFSBASE,SMEP,ENHMOVSB>
>   Thermal and PM Features=0x75<SENSOR,ARAT,PLN,ECMD,PTM>
>   MONITOR/MWAIT Features=0x3<CST,INTBRK>
> real memory  = 8477464576 (8084 MB)
> avail memory = 7884136448 (7518 MB)
> lapic: divisor index 0, frequency 49886793 Hz
> srat_probe: can't locate SRAT
> Initialize MI interrupts
> TSC testing MP synchronization ...
> cpu1: TSC is not MP synchronized @0
> TSC is not MP synchronized
> VMM: available, disabled by default
> wdog: In-kernel automatic watchdog reset enabled
> kbd1 at kbdmux0
> md0: Malloc disk
> interrupt uses mplock: swi_taskq
> ACPI: RSDP 0x00000000000F0490 000024 (v02 ALASKA)
> ACPI: XSDT 0x00000000DA781070 000064 (v01 ALASKA A M I    01072009 AMI  00010013)
> ACPI: FACP 0x00000000DA78C908 00010C (v05 ALASKA A M I    01072009 AMI  00010013)
> ACPI: DSDT 0x00000000DA781168 00B79B (v02 ALASKA A M I    00000028 INTL 20051117)
> ACPI: FACS 0x00000000DABB7080 000040
> ACPI: APIC 0x00000000DA78CA18 000062 (v03 ALASKA A M I    01072009 AMI  00010013)
> ACPI: FPDT 0x00000000DA78CA80 000044 (v01 ALASKA A M I    01072009 AMI  00010013)
> ACPI: MCFG 0x00000000DA78CAC8 00003C (v01 ALASKA A M I    01072009 MSFT 00000097)
> ACPI: HPET 0x00000000DA78CB08 000038 (v01 ALASKA A M I    01072009 AMI. 00000005)
> ACPI: SSDT 0x00000000DA78CB40 000315 (v01 SataRe SataTabl 00001000 INTL 20091112)
> ACPI: SSDT 0x00000000DA78CE58 000860 (v01 PmRef  Cpu0Ist  00003000 INTL 20051117)
> ACPI: SSDT 0x00000000DA78D6B8 000B22 (v01 PmRef  CpuPm    00003000 INTL 20051117)
> cryptosoft0: <software crypto> on motherboard
> aesni0: No AESNI support.
> padlock0: No ACE support.
> rdrand0: No RdRand support.
> acpi0: <ALASKA A M I> on motherboard
> ACPI: Executed 1 blocks of module-level executable AML code
> ACPI: 4 ACPI AML tables successfully acquired and loaded
> ACPI FADT: SCI testing interrupt mode ...
> ACPI FADT: SCI select level/high
> acpi0: Power Button (fixed)
> acpi_timer0 on acpi0
> acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
> acpi_hpet0: frequency 14318180
> pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
> pci0: <ACPI PCI bus> on pcib0
> vgapci0: <VGA-compatible display> port 0xf000-0xf03f mem 0xe0000000-0xefffffff,0xf7800000-0xf7bfffff irq 16 at device 2.0 on pci0
> vgapci0: Boot video device
> pci0: <simple comms> (vendor 0x8086, dev 0x1e3a) at device 22.0 irq 16
> ehci0: <Intel Panther Point USB 2.0 controller> mem 0xf7d08000-0xf7d083ff irq 16 at device 26.0 on pci0
> usbus0: EHCI version 1.0
> usbus0 on ehci0
> pci0: <multimedia, HDA> (vendor 0x8086, dev 0x1e20) at device 27.0 irq 22
> pcib1: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0
> pci1: <ACPI PCI bus> on pcib1
> usbus0: 480Mbps High Speed USB v2.0
> pcib2: <ACPI PCI-PCI bridge> irq 18 at device 28.2 on pci0
> pci2: <ACPI PCI bus> on pcib2
> re0: <RealTek 8111/8168 PCIe Gigabit Ethernet> port 0xe000-0xe0ff mem 0xf0000000-0xf0003fff,0xf7c00000-0xf7c00fff irq 18 at device 0.0 on pci2
> re0: MAC version 0x2c900000, MACFG 39, support MSI
> re0: bus speed 125MHz
> ugen0.1: <Intel> at usbus0
> uhub0: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0
> re0: MAC address: b8:ae:ed:3c:ce:35
> ehci1: <Intel Panther Point USB 2.0 controller> mem 0xf7d07000-0xf7d073ff irq 23 at device 29.0 on pci0
> usbus1: EHCI version 1.0
> usbus1 on ehci1
> isab0: <PCI-ISA bridge> at device 31.0 on pci0
> isa0: <ISA bus> on isab0
> ahci0: <AHCI-PCI-SATA> port 0xf060-0xf07f,0xf080-0xf083,0xf090-0xf097,0xf0a0-0xf0a3,0xf0b0-0xf0b7 mem 0xf7d06000-0xf7d067ff irq 16 at device 31.2 on pci0
> usbus1: 480Mbps High Speed USB v2.0
> ugen1.1: <Intel> at usbus1
> uhub1: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1
> ahci0: Intel hocus pocus
> ahci0: AHCI 1.3 cap 0xc730ff43<S64A,NCQ,SALP,SAL,SCLO,PMD,SSC,PSC,EMS> cap2 0x4<APST>, 4 ports, 32 tags/port, gen 3 (6Gbps)
> uhub0: 2 ports with 2 removable, self powered
> uhub1: 2 ports with 2 removable, self powered
> ugen0.2: <vendor 0x8087> at usbus0
> uhub2: <vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr 2> on usbus0
> ugen1.2: <vendor 0x8087> at usbus1
> uhub3: <vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr 2> on usbus1
> uhub2: 4 ports with 4 removable, self powered
> uhub3: 4 ports with 4 removable, self powered
> ugen1.3: <DELL> at usbus1
> ukbd0: <DELL Dell USB Entry Keyboard, class 0/0, rev 1.10/1.78, addr 3> on usbus1
> kbd2 at ukbd0
> ahci0.0: Found SSD "TS32GMTS400 20140516" serial="B620550018"
> ahci0.0: tags=32/32 satacap=830e satacap2=0086 satafea=054c NCQ=YES capacity=30533.83MB
> ahci0.0: f85=7469 f86=b401 f87=4063 WC=enabled RA=enabled SEC=frozen
> ahci0.2: Found DISK "WDC WD30EZRX-00MMMB0 80.00A80" serial="WD-WCAWZ2969584"
> ahci0.2: tags=32/32 satacap=170e satacap2=0004 satafea=0044 NCQ=YES capacity=2861588.46MB
> ahci0.2: f85=7469 f86=bc41 f87=4123 WC=enabled RA=enabled SEC=frozen
> ahci0.4: Found DISK "WDC WD30EZRX-00MMMB0 80.00A80" serial="WD-WCAWZ2111282"
> ahci0.4: tags=32/32 satacap=170e satacap2=0004 satafea=0044 NCQ=YES capacity=2861588.46MB
> ahci0.4: f85=7469 f86=bc41 f87=4123 WC=enabled RA=enabled SEC=frozen
> ahci0.5: No device detected
> pci0: <serial bus, SMBus> (vendor 0x8086, dev 0x1e22) at device 31.3 irq 18
> acpi_button0: <Power Button> on acpi0
> acpi_tz0: <Thermal Zone> on acpi0
> acpi_tz1: <Thermal Zone> on acpi0
> sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 on acpi0
> sio0: type 16550A
> sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0
> sio1: type 16550A
> cpu0: <ACPI CPU> on acpi0
> ACPI: Dynamic OEM Table Load:
> ACPI: SSDT 0xFFFFFF81D7025200 00083B (v01 PmRef  Cpu0Cst  00003001 INTL 20051117)
> cpu_cst0: <ACPI CPU C-State> on cpu0
> cpu_pst0: <ACPI CPU P-State> on cpu0
> clockmod0: <CPU clock modulation> on cpu0
> perfbias0: <CPU perf-energy bias> on cpu0
> coretemp0: <CPU On-Die Thermal Sensors> on cpu0
> cpu1: <ACPI CPU> on acpi0
> ACPI: Dynamic OEM Table Load:
> ACPI: SSDT 0xFFFFFF81DBEEF140 000303 (v01 PmRef  ApIst    00003000 INTL 20051117)
> ACPI: Dynamic OEM Table Load:
> ACPI: SSDT 0xFFFFFF805BBF7F40 000119 (v01 PmRef  ApCst    00003000 INTL 20051117)
> cpu_cst1: <ACPI CPU C-State> on cpu1
> cpu_pst1: <ACPI CPU P-State> on cpu1
> clockmod1: <CPU clock modulation> on cpu1
> perfbias1: <CPU perf-energy bias> on cpu1
> coretemp1: <CPU On-Die Thermal Sensors> on cpu1
> ACPI: Enabled 6 GPEs in block 00 to 3F
> orm0: <ISA Option ROM> at iomem 0xc0000-0xcefff on isa0
> pmtimer0 on isa0
> atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
> atkbd0: <AT Keyboard> irq 1 on atkbdc0
> kbd0 at atkbd0
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
> sc0: <System console> at flags 0x500 on isa0
> sc0: VGA <16 virtual consoles, flags=0x300>
> hpt27xx: no controller detected.
> CAM: Configuring 4 busses
> CAM: finished configuring all busses
> da0 at ahci0 bus 0 target 0 lun 0
> da0: <SATA TS32GMTS400 2014> Fixed Direct Access SCSI-4 device
> da0: Serial Number B620550018
> da0: 600.000MB/s transfers
> da0: 30533MB (62533296 512 byte sectors: 255H 63S/T 3892C)
> da0: supports TRIM
> da1 at ahci0 bus 2 target 0 lun 0
> da1: <SATA WDC WD30EZRX-00M 80.0> Fixed Direct Access SCSI-4 device
> da1: Serial Number WD-WCAWZ2969584
> da1: 300.000MB/s transfers
> da1: 2861588MB (5860533168 512 byte sectors: 255H 63S/T 364801C)
> da2 at ahci0 bus 4 target 0 lun 0
> da2: <SATA WDC WD30EZRX-00M 80.0> Fixed Direct Access SCSI-4 device
> da2: Serial Number WD-WCAWZ2111282
> da2: 300.000MB/s transfers
> da2: 2861588MB (5860533168 512 byte sectors: 255H 63S/T 364801C)
> da1 part 0: unavailable, bad start or ending lba
> da2 part 0: unavailable, bad start or ending lba
> no B_DEVMAGIC (bootdev=0)
> Mounting root from hammer:serno/B620550018.s1d
> HAMMER(ROOT) recovery check seqno=0899bed3
> HAMMER(ROOT) recovery range 3000000014442e30-3000000014442e30
> HAMMER(ROOT) recovery nexto 3000000014442e30 endseqno=0899bed4
> HAMMER(ROOT) mounted clean, no recovery needed
> DMA space used: 10428k, remaining available: 131072k
> Mounting devfs
> HAMMER(DATA) recovery check seqno=2fa25c1d
> HAMMER(DATA) recovery range 3000000034605ad0-3000000034605ad0
> HAMMER(DATA) recovery nexto 3000000034605ad0 endseqno=2fa25c1e
> HAMMER(DATA) mounted clean, no recovery needed
> HAMMER(BACKUP) recovery check seqno=040a1f5b
> HAMMER(BACKUP) recovery range 300000003034ce98-300000003034ce98
> HAMMER(BACKUP) recovery nexto 300000003034ce98 endseqno=040a1f5c
> HAMMER(BACKUP) mounted clean, no recovery needed
> swap low/high-water marks set to 67683/101525
> pflog0: promiscuous mode enabled
> boot() called on cpu#1
> Switching to cpu #0 for shutdown
> Waiting (max 60 seconds) for system thread swapcached to stop...stopped
> Waiting (max 60 seconds) for system thread vnlru to stop...stopped
> Waiting (max 60 seconds) for system thread consttyd to stop...stopped
> Waiting (max 60 seconds) for system thread bufdaemon to stop...stopped
> Waiting (max 60 seconds) for system thread bufdaemon_hw to stop...stopped
>
> syncing disks... 137 105 105
> done
> Copyright (c) 2003-2017 The DragonFly Project.
> Copyright (c) 1992-2003 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
>         The Regents of the University of California. All rights reserved.
> DragonFly v4.8.0.1.g86163-RELEASE #4: Tue Mar 28 07:56:27 EST 2017
>     root at dfly.bagdala2.net:/usr/obj/usr/src/sys/X86_64_GENERIC
> i8254 clock: 1193300 Hz
> TSC invariant clock: 1795933432 Hz
> CPU: Intel(R) Celeron(R) CPU 1037U @ 1.80GHz (1795.93-MHz K8-class CPU)
>   Origin = "GenuineIntel"  Id = 0x306a9  Stepping = 9
>   Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
>   Features2=0x5bae3bf<SSE3,PCLMULQDQ,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,POPCNT,TSCDLT,XSAVE>
>   AMD Features=0x28100800<SYSCALL,NX,RDTSCP,LM>
>   AMD Features2=0x1<LAHF>
>   Structured Extended Features=0x281<GSFSBASE,SMEP,ENHMOVSB>
>   Thermal and PM Features=0x75<SENSOR,ARAT,PLN,ECMD,PTM>
>   MONITOR/MWAIT Features=0x3<CST,INTBRK>
> real memory  = 8477464576 (8084 MB)
> avail memory = 7884136448 (7518 MB)
> lapic: divisor index 0, frequency 49886884 Hz
> srat_probe: can't locate SRAT
> Initialize MI interrupts
> TSC testing MP synchronization ...
> cpu1: TSC is not MP synchronized @0
> TSC is not MP synchronized
> VMM: available, disabled by default
> wdog: In-kernel automatic watchdog reset enabled
> kbd1 at kbdmux0
> md0: Malloc disk
> interrupt uses mplock: swi_taskq
> ACPI: RSDP 0x00000000000F0490 000024 (v02 ALASKA)
> ACPI: XSDT 0x00000000DA781070 000064 (v01 ALASKA A M I    01072009 AMI  00010013)
> ACPI: FACP 0x00000000DA78C908 00010C (v05 ALASKA A M I    01072009 AMI  00010013)
> ACPI: DSDT 0x00000000DA781168 00B79B (v02 ALASKA A M I    00000028 INTL 20051117)
> ACPI: FACS 0x00000000DABB7080 000040
> ACPI: APIC 0x00000000DA78CA18 000062 (v03 ALASKA A M I    01072009 AMI  00010013)
> ACPI: FPDT 0x00000000DA78CA80 000044 (v01 ALASKA A M I    01072009 AMI  00010013)
> ACPI: MCFG 0x00000000DA78CAC8 00003C (v01 ALASKA A M I    01072009 MSFT 00000097)
> ACPI: HPET 0x00000000DA78CB08 000038 (v01 ALASKA A M I    01072009 AMI. 00000005)
> ACPI: SSDT 0x00000000DA78CB40 000315 (v01 SataRe SataTabl 00001000 INTL 20091112)
> ACPI: SSDT 0x00000000DA78CE58 000860 (v01 PmRef  Cpu0Ist  00003000 INTL 20051117)
> ACPI: SSDT 0x00000000DA78D6B8 000B22 (v01 PmRef  CpuPm    00003000 INTL 20051117)
> cryptosoft0: <software crypto> on motherboard
> aesni0: No AESNI support.
> padlock0: No ACE support.
> rdrand0: No RdRand support.
> acpi0: <ALASKA A M I> on motherboard
> ACPI: Executed 1 blocks of module-level executable AML code
> ACPI: 4 ACPI AML tables successfully acquired and loaded
> ACPI FADT: SCI testing interrupt mode ...
> ACPI FADT: SCI select level/high
> acpi0: Power Button (fixed)
> acpi_timer0 on acpi0
> acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
> acpi_hpet0: frequency 14318180
> pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
> pci0: <ACPI PCI bus> on pcib0
> vgapci0: <VGA-compatible display> port 0xf000-0xf03f mem 0xe0000000-0xefffffff,0xf7800000-0xf7bfffff irq 16 at device 2.0 on pci0
> vgapci0: Boot video device
> pci0: <simple comms> (vendor 0x8086, dev 0x1e3a) at device 22.0 irq 16
> ehci0: <Intel Panther Point USB 2.0 controller> mem 0xf7d08000-0xf7d083ff irq 16 at device 26.0 on pci0
> usbus0: EHCI version 1.0
> usbus0 on ehci0
> pci0: <multimedia, HDA> (vendor 0x8086, dev 0x1e20) at device 27.0 irq 22
> pcib1: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0
> pci1: <ACPI PCI bus> on pcib1
> usbus0: 480Mbps High Speed USB v2.0
> pcib2: <ACPI PCI-PCI bridge> irq 18 at device 28.2 on pci0
> pci2: <ACPI PCI bus> on pcib2
> re0: <RealTek 8111/8168 PCIe Gigabit Ethernet> port 0xe000-0xe0ff mem 0xf0000000-0xf0003fff,0xf7c00000-0xf7c00fff irq 18 at device 0.0 on pci2
> re0: MAC version 0x2c900000, MACFG 39, support MSI
> re0: bus speed 125MHz
> ugen0.1: <Intel> at usbus0
> uhub0: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0
> re0: MAC address: b8:ae:ed:3c:ce:35
> ehci1: <Intel Panther Point USB 2.0 controller> mem 0xf7d07000-0xf7d073ff irq 23 at device 29.0 on pci0
> usbus1: EHCI version 1.0
> usbus1 on ehci1
> isab0: <PCI-ISA bridge> at device 31.0 on pci0
> isa0: <ISA bus> on isab0
> ahci0: <AHCI-PCI-SATA> port 0xf060-0xf07f,0xf080-0xf083,0xf090-0xf097,0xf0a0-0xf0a3,0xf0b0-0xf0b7 mem 0xf7d06000-0xf7d067ff irq 16 at device 31.2 on pci0
> usbus1: 480Mbps High Speed USB v2.0
> ugen1.1: <Intel> at usbus1
> uhub1: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1
> ahci0: Intel hocus pocus
> ahci0: AHCI 1.3 cap 0xc730ff43<S64A,NCQ,SALP,SAL,SCLO,PMD,SSC,PSC,EMS> cap2 0x4<APST>, 4 ports, 32 tags/port, gen 3 (6Gbps)
> uhub0: 2 ports with 2 removable, self powered
> uhub1: 2 ports with 2 removable, self powered
> ugen0.2: <vendor 0x8087> at usbus0
> uhub2: <vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr 2> on usbus0
> ugen1.2: <vendor 0x8087> at usbus1
> uhub3: <vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr 2> on usbus1
> uhub2: 4 ports with 4 removable, self powered
> uhub3: 4 ports with 4 removable, self powered
> ugen1.3: <DELL> at usbus1
> ukbd0: <DELL Dell USB Entry Keyboard, class 0/0, rev 1.10/1.78, addr 3> on usbus1
> kbd2 at ukbd0
> ahci0.0: Found SSD "TS32GMTS400 20140516" serial="B620550018"
> ahci0.0: tags=32/32 satacap=830e satacap2=0086 satafea=054c NCQ=YES capacity=30533.83MB
> ahci0.0: f85=7469 f86=b401 f87=4063 WC=enabled RA=enabled SEC=frozen
> ahci0.2: Found DISK "WDC WD30EZRX-00MMMB0 80.00A80" serial="WD-WCAWZ2969584"
> ahci0.2: tags=32/32 satacap=170e satacap2=0004 satafea=0044 NCQ=YES capacity=2861588.46MB
> ahci0.2: f85=7469 f86=bc41 f87=4123 WC=enabled RA=enabled SEC=frozen
> ahci0.4: Found DISK "WDC WD30EZRX-00MMMB0 80.00A80" serial="WD-WCAWZ2111282"
> ahci0.4: tags=32/32 satacap=170e satacap2=0004 satafea=0044 NCQ=YES capacity=2861588.46MB
> ahci0.4: f85=7469 f86=bc41 f87=4123 WC=enabled RA=enabled SEC=frozen
> ahci0.5: No device detected
> pci0: <serial bus, SMBus> (vendor 0x8086, dev 0x1e22) at device 31.3 irq 18
> acpi_button0: <Power Button> on acpi0
> acpi_tz0: <Thermal Zone> on acpi0
> acpi_tz1: <Thermal Zone> on acpi0
> sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 on acpi0
> sio0: type 16550A
> sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0
> sio1: type 16550A
> cpu0: <ACPI CPU> on acpi0
> ACPI: Dynamic OEM Table Load:
> ACPI: SSDT 0xFFFFFF81D7025200 00083B (v01 PmRef  Cpu0Cst  00003001 INTL 20051117)
> cpu_cst0: <ACPI CPU C-State> on cpu0
> cpu_pst0: <ACPI CPU P-State> on cpu0
> clockmod0: <CPU clock modulation> on cpu0
> perfbias0: <CPU perf-energy bias> on cpu0
> coretemp0: <CPU On-Die Thermal Sensors> on cpu0
> cpu1: <ACPI CPU> on acpi0
> ACPI: Dynamic OEM Table Load:
> ACPI: SSDT 0xFFFFFF81DBEEF140 000303 (v01 PmRef  ApIst    00003000 INTL 20051117)
> ACPI: Dynamic OEM Table Load:
> ACPI: SSDT 0xFFFFFF805BBF7F40 000119 (v01 PmRef  ApCst    00003000 INTL 20051117)
> cpu_cst1: <ACPI CPU C-State> on cpu1
> cpu_pst1: <ACPI CPU P-State> on cpu1
> clockmod1: <CPU clock modulation> on cpu1
> perfbias1: <CPU perf-energy bias> on cpu1
> coretemp1: <CPU On-Die Thermal Sensors> on cpu1
> ACPI: Enabled 6 GPEs in block 00 to 3F
> orm0: <ISA Option ROM> at iomem 0xc0000-0xcefff on isa0
> pmtimer0 on isa0
> atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
> atkbd0: <AT Keyboard> irq 1 on atkbdc0
> kbd0 at atkbd0
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
> sc0: <System console> at flags 0x500 on isa0
> sc0: VGA <16 virtual consoles, flags=0x300>
> hpt27xx: no controller detected.
> CAM: Configuring 4 busses
> CAM: finished configuring all busses
> da0 at ahci0 bus 0 target 0 lun 0
> da0: <SATA TS32GMTS400 2014> Fixed Direct Access SCSI-4 device
> da0: Serial Number B620550018
> da0: 600.000MB/s transfers
> da0: 30533MB (62533296 512 byte sectors: 255H 63S/T 3892C)
> da0: supports TRIM
> da1 at ahci0 bus 2 target 0 lun 0
> da1: <SATA WDC WD30EZRX-00M 80.0> Fixed Direct Access SCSI-4 device
> da1: Serial Number WD-WCAWZ2969584
> da1: 300.000MB/s transfers
> da1: 2861588MB (5860533168 512 byte sectors: 255H 63S/T 364801C)
> da2 at ahci0 bus 4 target 0 lun 0
> da2: <SATA WDC WD30EZRX-00M 80.0> Fixed Direct Access SCSI-4 device
> da2: Serial Number WD-WCAWZ2111282
> da2: 300.000MB/s transfers
> da2: 2861588MB (5860533168 512 byte sectors: 255H 63S/T 364801C)
> da1 part 0: unavailable, bad start or ending lba
> da2 part 0: unavailable, bad start or ending lba
> no B_DEVMAGIC (bootdev=0)
> Mounting root from hammer:serno/B620550018.s1d
> HAMMER(ROOT) recovery check seqno=0899cf95
> HAMMER(ROOT) recovery range 3000000014612ea8-3000000014612ea8
> HAMMER(ROOT) recovery nexto 3000000014612ea8 endseqno=0899cf96
> HAMMER(ROOT) mounted clean, no recovery needed
> DMA space used: 10428k, remaining available: 131072k
> Mounting devfs
> HAMMER(DATA) recovery check seqno=2fa3a14d
> HAMMER(DATA) recovery range 3000000036618778-3000000036618778
> HAMMER(DATA) recovery nexto 3000000036618778 endseqno=2fa3a14e
> HAMMER(DATA) mounted clean, no recovery needed
> HAMMER(BACKUP) recovery check seqno=040a2f3c
> HAMMER(BACKUP) recovery range 300000003051ff80-300000003051ff80
> HAMMER(BACKUP) recovery nexto 300000003051ff80 endseqno=040a2f3d
> HAMMER(BACKUP) mounted clean, no recovery needed
> swap low/high-water marks set to 67683/101525
> pflog0: promiscuous mode enabled
> boot() called on cpu#0
> Waiting (max 60 seconds) for system thread swapcached to stop...stopped
> Waiting (max 60 seconds) for system thread vnlru to stop...stopped
> Waiting (max 60 seconds) for system thread consttyd to stop...stopped
> Waiting (max 60 seconds) for system thread bufdaemon to stop...stopped
> Waiting (max 60 seconds) for system thread bufdaemon_hw to stop...stopped
>
> syncing disks...
> done
> vflush: Warning, cannot destroy busy device vnode
> unmount of filesystem mounted from devfs failed (BUSY)
> unmount(0xffffff81d6e23cc0): Forced unmount: 0 namecache references still present
> unmount(0xffffff81d6e23cc0): Forced unmount: 1 mount refs still present
> Copyright (c) 2003-2017 The DragonFly Project.
> Copyright (c) 1992-2003 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
>         The Regents of the University of California. All rights reserved.
> DragonFly v4.8.0.1.g86163-RELEASE #4: Tue Mar 28 07:56:27 EST 2017
>     root at dfly.bagdala2.net:/usr/obj/usr/src/sys/X86_64_GENERIC
> i8254 clock: 1193291 Hz
> TSC invariant clock: 1795935104 Hz
> CPU: Intel(R) Celeron(R) CPU 1037U @ 1.80GHz (1795.94-MHz K8-class CPU)
>   Origin = "GenuineIntel"  Id = 0x306a9  Stepping = 9
>   Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
>   Features2=0x5bae3bf<SSE3,PCLMULQDQ,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,POPCNT,TSCDLT,XSAVE>
>   AMD Features=0x28100800<SYSCALL,NX,RDTSCP,LM>
>   AMD Features2=0x1<LAHF>
>   Structured Extended Features=0x281<GSFSBASE,SMEP,ENHMOVSB>
>   Thermal and PM Features=0x75<SENSOR,ARAT,PLN,ECMD,PTM>
>   MONITOR/MWAIT Features=0x3<CST,INTBRK>
> real memory  = 8477464576 (8084 MB)
> avail memory = 7884136448 (7518 MB)
> lapic: divisor index 0, frequency 49886870 Hz
> srat_probe: can't locate SRAT
> Initialize MI interrupts
> TSC testing MP synchronization ...
> cpu1: TSC is not MP synchronized @0
> TSC is not MP synchronized
> VMM: available, disabled by default
> wdog: In-kernel automatic watchdog reset enabled
> kbd1 at kbdmux0
> md0: Malloc disk
> interrupt uses mplock: swi_taskq
> ACPI: RSDP 0x00000000000F0490 000024 (v02 ALASKA)
> ACPI: XSDT 0x00000000DA781070 000064 (v01 ALASKA A M I    01072009 AMI  00010013)
> ACPI: FACP 0x00000000DA78C908 00010C (v05 ALASKA A M I    01072009 AMI  00010013)
> ACPI: DSDT 0x00000000DA781168 00B79B (v02 ALASKA A M I    00000028 INTL 20051117)
> ACPI: FACS 0x00000000DABB7080 000040
> ACPI: APIC 0x00000000DA78CA18 000062 (v03 ALASKA A M I    01072009 AMI  00010013)
> ACPI: FPDT 0x00000000DA78CA80 000044 (v01 ALASKA A M I    01072009 AMI  00010013)
> ACPI: MCFG 0x00000000DA78CAC8 00003C (v01 ALASKA A M I    01072009 MSFT 00000097)
> ACPI: HPET 0x00000000DA78CB08 000038 (v01 ALASKA A M I    01072009 AMI. 00000005)
> ACPI: SSDT 0x00000000DA78CB40 000315 (v01 SataRe SataTabl 00001000 INTL 20091112)
> ACPI: SSDT 0x00000000DA78CE58 000860 (v01 PmRef  Cpu0Ist  00003000 INTL 20051117)
> ACPI: SSDT 0x00000000DA78D6B8 000B22 (v01 PmRef  CpuPm    00003000 INTL 20051117)
> cryptosoft0: <software crypto> on motherboard
> aesni0: No AESNI support.
> padlock0: No ACE support.
> rdrand0: No RdRand support.
> acpi0: <ALASKA A M I> on motherboard
> ACPI: Executed 1 blocks of module-level executable AML code
> ACPI: 4 ACPI AML tables successfully acquired and loaded
> ACPI FADT: SCI testing interrupt mode ...
> ACPI FADT: SCI select level/high
> acpi0: Power Button (fixed)
> acpi_timer0 on acpi0
> acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
> acpi_hpet0: frequency 14318180
> pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
> pci0: <ACPI PCI bus> on pcib0
> vgapci0: <VGA-compatible display> port 0xf000-0xf03f mem 0xe0000000-0xefffffff,0xf7800000-0xf7bfffff irq 16 at device 2.0 on pci0
> vgapci0: Boot video device
> pci0: <simple comms> (vendor 0x8086, dev 0x1e3a) at device 22.0 irq 16
> ehci0: <Intel Panther Point USB 2.0 controller> mem 0xf7d08000-0xf7d083ff irq 16 at device 26.0 on pci0
> usbus0: EHCI version 1.0
> usbus0 on ehci0
> pci0: <multimedia, HDA> (vendor 0x8086, dev 0x1e20) at device 27.0 irq 22
> pcib1: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0
> pci1: <ACPI PCI bus> on pcib1
> usbus0: 480Mbps High Speed USB v2.0
> pcib2: <ACPI PCI-PCI bridge> irq 18 at device 28.2 on pci0
> pci2: <ACPI PCI bus> on pcib2
> re0: <RealTek 8111/8168 PCIe Gigabit Ethernet> port 0xe000-0xe0ff mem 0xf0000000-0xf0003fff,0xf7c00000-0xf7c00fff irq 18 at device 0.0 on pci2
> re0: MAC version 0x2c900000, MACFG 39, support MSI
> re0: bus speed 125MHz
> ugen0.1: <Intel> at usbus0
> uhub0: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0
> re0: MAC address: b8:ae:ed:3c:ce:35
> ehci1: <Intel Panther Point USB 2.0 controller> mem 0xf7d07000-0xf7d073ff irq 23 at device 29.0 on pci0
> usbus1: EHCI version 1.0
> usbus1 on ehci1
> isab0: <PCI-ISA bridge> at device 31.0 on pci0
> isa0: <ISA bus> on isab0
> ahci0: <AHCI-PCI-SATA> port 0xf060-0xf07f,0xf080-0xf083,0xf090-0xf097,0xf0a0-0xf0a3,0xf0b0-0xf0b7 mem 0xf7d06000-0xf7d067ff irq 16 at device 31.2 on pci0
> usbus1: 480Mbps High Speed USB v2.0
> ugen1.1: <Intel> at usbus1
> uhub1: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1
> ahci0: Intel hocus pocus
> ahci0: AHCI 1.3 cap 0xc730ff43<S64A,NCQ,SALP,SAL,SCLO,PMD,SSC,PSC,EMS> cap2 0x4<APST>, 4 ports, 32 tags/port, gen 3 (6Gbps)
> uhub0: 2 ports with 2 removable, self powered
> uhub1: 2 ports with 2 removable, self powered
> ugen0.2: <vendor 0x8087> at usbus0
> uhub2: <vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr 2> on usbus0
> ugen1.2: <vendor 0x8087> at usbus1
> uhub3: <vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr 2> on usbus1
> uhub2: 4 ports with 4 removable, self powered
> uhub3: 4 ports with 4 removable, self powered
> ugen1.3: <DELL> at usbus1
> ukbd0: <DELL Dell USB Entry Keyboard, class 0/0, rev 1.10/1.78, addr 3> on usbus1
> kbd2 at ukbd0
> ahci0.0: Found SSD "TS32GMTS400 20140516" serial="B620550018"
> ahci0.0: tags=32/32 satacap=830e satacap2=0086 satafea=054c NCQ=YES capacity=30533.83MB
> ahci0.0: f85=7469 f86=b401 f87=4063 WC=enabled RA=enabled SEC=frozen
> ahci0.2: Found DISK "WDC WD30EZRX-00MMMB0 80.00A80" serial="WD-WCAWZ2969584"
> ahci0.2: tags=32/32 satacap=170e satacap2=0004 satafea=0044 NCQ=YES capacity=2861588.46MB
> ahci0.2: f85=7469 f86=bc41 f87=4123 WC=enabled RA=enabled SEC=frozen
> ahci0.4: Found DISK "WDC WD30EZRX-00MMMB0 80.00A80" serial="WD-WCAWZ2111282"
> ahci0.4: tags=32/32 satacap=170e satacap2=0004 satafea=0044 NCQ=YES capacity=2861588.46MB
> ahci0.4: f85=7469 f86=bc41 f87=4123 WC=enabled RA=enabled SEC=frozen
> ahci0.5: No device detected
> pci0: <serial bus, SMBus> (vendor 0x8086, dev 0x1e22) at device 31.3 irq 18
> acpi_button0: <Power Button> on acpi0
> acpi_tz0: <Thermal Zone> on acpi0
> acpi_tz1: <Thermal Zone> on acpi0
> sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 on acpi0
> sio0: type 16550A
> sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0
> sio1: type 16550A
> cpu0: <ACPI CPU> on acpi0
> ACPI: Dynamic OEM Table Load:
> ACPI: SSDT 0xFFFFFF81D7025200 00083B (v01 PmRef  Cpu0Cst  00003001 INTL 20051117)
> cpu_cst0: <ACPI CPU C-State> on cpu0
> cpu_pst0: <ACPI CPU P-State> on cpu0
> clockmod0: <CPU clock modulation> on cpu0
> perfbias0: <CPU perf-energy bias> on cpu0
> coretemp0: <CPU On-Die Thermal Sensors> on cpu0
> cpu1: <ACPI CPU> on acpi0
> ACPI: Dynamic OEM Table Load:
> ACPI: SSDT 0xFFFFFF81DBEEF140 000303 (v01 PmRef  ApIst    00003000 INTL 20051117)
> ACPI: Dynamic OEM Table Load:
> ACPI: SSDT 0xFFFFFF805BBF7F40 000119 (v01 PmRef  ApCst    00003000 INTL 20051117)
> cpu_cst1: <ACPI CPU C-State> on cpu1
> cpu_pst1: <ACPI CPU P-State> on cpu1
> clockmod1: <CPU clock modulation> on cpu1
> perfbias1: <CPU perf-energy bias> on cpu1
> coretemp1: <CPU On-Die Thermal Sensors> on cpu1
> ACPI: Enabled 6 GPEs in block 00 to 3F
> orm0: <ISA Option ROM> at iomem 0xc0000-0xcefff on isa0
> pmtimer0 on isa0
> atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
> atkbd0: <AT Keyboard> irq 1 on atkbdc0
> kbd0 at atkbd0
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
> sc0: <System console> at flags 0x500 on isa0
> sc0: VGA <16 virtual consoles, flags=0x300>
> hpt27xx: no controller detected.
> CAM: Configuring 4 busses
> CAM: finished configuring all busses
> da0 at ahci0 bus 0 target 0 lun 0
> da0: <SATA TS32GMTS400 2014> Fixed Direct Access SCSI-4 device
> da0: Serial Number B620550018
> da0: 600.000MB/s transfers
> da0: 30533MB (62533296 512 byte sectors: 255H 63S/T 3892C)
> da0: supports TRIM
> da1 at ahci0 bus 2 target 0 lun 0
> da1: <SATA WDC WD30EZRX-00M 80.0> Fixed Direct Access SCSI-4 device
> da1: Serial Number WD-WCAWZ2969584
> da1: 300.000MB/s transfers
> da1: 2861588MB (5860533168 512 byte sectors: 255H 63S/T 364801C)
> da2 at ahci0 bus 4 target 0 lun 0
> da2: <SATA WDC WD30EZRX-00M 80.0> Fixed Direct Access SCSI-4 device
> da2: Serial Number WD-WCAWZ2111282
> da2: 300.000MB/s transfers
> da2: 2861588MB (5860533168 512 byte sectors: 255H 63S/T 364801C)
> da1 part 0: unavailable, bad start or ending lba
> da2 part 0: unavailable, bad start or ending lba
> no B_DEVMAGIC (bootdev=0)
> Mounting root from hammer:serno/B620550018.s1d
> HAMMER(ROOT) recovery check seqno=0899d83f
> HAMMER(ROOT) recovery range 3000000014705cc0-3000000014705cc0
> HAMMER(ROOT) recovery nexto 3000000014705cc0 endseqno=0899d840
> HAMMER(ROOT) mounted clean, no recovery needed
> DMA space used: 10428k, remaining available: 131072k
> Mounting devfs
> HAMMER(DATA) recovery check seqno=2fa3a14d
> HAMMER(DATA) recovery range 3000000036618778-3000000036618778
> HAMMER(DATA) recovery nexto 3000000036618778 endseqno=2fa3a14e
> HAMMER(DATA) mounted clean, no recovery needed
> HAMMER(BACKUP) recovery check seqno=040b37a1
> HAMMER(BACKUP) recovery range 300000003238b358-300000003238b358
> HAMMER(BACKUP) recovery nexto 300000003238b358 endseqno=040b37a2
> HAMMER(BACKUP) mounted clean, no recovery needed
> swap low/high-water marks set to 67683/101525
> pflog0: promiscuous mode enabled
> boot() called on cpu#1
> Switching to cpu #0 for shutdown
> Waiting (max 60 seconds) for system thread swapcached to stop...stopped
> Waiting (max 60 seconds) for system thread vnlru to stop...stopped
> Waiting (max 60 seconds) for system thread consttyd to stop...stopped
> Waiting (max 60 seconds) for system thread bufdaemon to stop...stopped
> Waiting (max 60 seconds) for system thread bufdaemon_hw to stop...stopped
>
> syncing disks...
> done
> vflush: Warning, cannot destroy busy device vnode
> unmount of filesystem mounted from devfs failed (BUSY)
> unmount(0xffffff81d6e23cc0): Forced unmount: 0 namecache references still present
> unmount(0xffffff81d6e23cc0): Forced unmount: 1 mount refs still present
> Copyright (c) 2003-2017 The DragonFly Project.
> Copyright (c) 1992-2003 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
>         The Regents of the University of California. All rights reserved.
> DragonFly v4.8.0.1.g86163-RELEASE #4: Tue Mar 28 07:56:27 EST 2017
>     root at dfly.bagdala2.net:/usr/obj/usr/src/sys/X86_64_GENERIC
> i8254 clock: 1193296 Hz
> TSC invariant clock: 1795934260 Hz
> CPU: Intel(R) Celeron(R) CPU 1037U @ 1.80GHz (1795.93-MHz K8-class CPU)
>   Origin = "GenuineIntel"  Id = 0x306a9  Stepping = 9
>   Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
>   Features2=0x5bae3bf<SSE3,PCLMULQDQ,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,POPCNT,TSCDLT,XSAVE>
>   AMD Features=0x28100800<SYSCALL,NX,RDTSCP,LM>
>   AMD Features2=0x1<LAHF>
>   Structured Extended Features=0x281<GSFSBASE,SMEP,ENHMOVSB>
>   Thermal and PM Features=0x75<SENSOR,ARAT,PLN,ECMD,PTM>
>   MONITOR/MWAIT Features=0x3<CST,INTBRK>
> real memory  = 8477464576 (8084 MB)
> avail memory = 7884136448 (7518 MB)
> lapic: divisor index 0, frequency 49886864 Hz
> srat_probe: can't locate SRAT
> Initialize MI interrupts
> TSC testing MP synchronization ...
> cpu1: TSC is not MP synchronized @0
> TSC is not MP synchronized
> VMM: available, disabled by default
> wdog: In-kernel automatic watchdog reset enabled
> kbd1 at kbdmux0
> md0: Malloc disk
> interrupt uses mplock: swi_taskq
> ACPI: RSDP 0x00000000000F0490 000024 (v02 ALASKA)
> ACPI: XSDT 0x00000000DA781070 000064 (v01 ALASKA A M I    01072009 AMI  00010013)
> ACPI: FACP 0x00000000DA78C908 00010C (v05 ALASKA A M I    01072009 AMI  00010013)
> ACPI: DSDT 0x00000000DA781168 00B79B (v02 ALASKA A M I    00000028 INTL 20051117)
> ACPI: FACS 0x00000000DABB7080 000040
> ACPI: APIC 0x00000000DA78CA18 000062 (v03 ALASKA A M I    01072009 AMI  00010013)
> ACPI: FPDT 0x00000000DA78CA80 000044 (v01 ALASKA A M I    01072009 AMI  00010013)
> ACPI: MCFG 0x00000000DA78CAC8 00003C (v01 ALASKA A M I    01072009 MSFT 00000097)
> ACPI: HPET 0x00000000DA78CB08 000038 (v01 ALASKA A M I    01072009 AMI. 00000005)
> ACPI: SSDT 0x00000000DA78CB40 000315 (v01 SataRe SataTabl 00001000 INTL 20091112)
> ACPI: SSDT 0x00000000DA78CE58 000860 (v01 PmRef  Cpu0Ist  00003000 INTL 20051117)
> ACPI: SSDT 0x00000000DA78D6B8 000B22 (v01 PmRef  CpuPm    00003000 INTL 20051117)
> cryptosoft0: <software crypto> on motherboard
> aesni0: No AESNI support.
> padlock0: No ACE support.
> rdrand0: No RdRand support.
> acpi0: <ALASKA A M I> on motherboard
> ACPI: Executed 1 blocks of module-level executable AML code
> ACPI: 4 ACPI AML tables successfully acquired and loaded
> ACPI FADT: SCI testing interrupt mode ...
> ACPI FADT: SCI select level/high
> acpi0: Power Button (fixed)
> acpi_timer0 on acpi0
> acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
> acpi_hpet0: frequency 14318180
> pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
> pci0: <ACPI PCI bus> on pcib0
> vgapci0: <VGA-compatible display> port 0xf000-0xf03f mem 0xe0000000-0xefffffff,0xf7800000-0xf7bfffff irq 16 at device 2.0 on pci0
> vgapci0: Boot video device
> pci0: <simple comms> (vendor 0x8086, dev 0x1e3a) at device 22.0 irq 16
> ehci0: <Intel Panther Point USB 2.0 controller> mem 0xf7d08000-0xf7d083ff irq 16 at device 26.0 on pci0
> usbus0: EHCI version 1.0
> usbus0 on ehci0
> pci0: <multimedia, HDA> (vendor 0x8086, dev 0x1e20) at device 27.0 irq 22
> pcib1: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0
> pci1: <ACPI PCI bus> on pcib1
> usbus0: 480Mbps High Speed USB v2.0
> pcib2: <ACPI PCI-PCI bridge> irq 18 at device 28.2 on pci0
> pci2: <ACPI PCI bus> on pcib2
> re0: <RealTek 8111/8168 PCIe Gigabit Ethernet> port 0xe000-0xe0ff mem 0xf0000000-0xf0003fff,0xf7c00000-0xf7c00fff irq 18 at device 0.0 on pci2
> re0: MAC version 0x2c900000, MACFG 39, support MSI
> re0: bus speed 125MHz
> ugen0.1: <Intel> at usbus0
> uhub0: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0
> re0: MAC address: b8:ae:ed:3c:ce:35
> ehci1: <Intel Panther Point USB 2.0 controller> mem 0xf7d07000-0xf7d073ff irq 23 at device 29.0 on pci0
> usbus1: EHCI version 1.0
> usbus1 on ehci1
> isab0: <PCI-ISA bridge> at device 31.0 on pci0
> isa0: <ISA bus> on isab0
> ahci0: <AHCI-PCI-SATA> port 0xf060-0xf07f,0xf080-0xf083,0xf090-0xf097,0xf0a0-0xf0a3,0xf0b0-0xf0b7 mem 0xf7d06000-0xf7d067ff irq 16 at device 31.2 on pci0
> usbus1: 480Mbps High Speed USB v2.0
> ugen1.1: <Intel> at usbus1
> uhub1: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1
> ahci0: Intel hocus pocus
> ahci0: AHCI 1.3 cap 0xc730ff43<S64A,NCQ,SALP,SAL,SCLO,PMD,SSC,PSC,EMS> cap2 0x4<APST>, 4 ports, 32 tags/port, gen 3 (6Gbps)
> uhub0: 2 ports with 2 removable, self powered
> uhub1: 2 ports with 2 removable, self powered
> ugen0.2: <vendor 0x8087> at usbus0
> uhub2: <vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr 2> on usbus0
> ugen1.2: <vendor 0x8087> at usbus1
> uhub3: <vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr 2> on usbus1
> uhub2: 4 ports with 4 removable, self powered
> uhub3: 4 ports with 4 removable, self powered
> ugen1.3: <DELL> at usbus1
> ukbd0: <DELL Dell USB Entry Keyboard, class 0/0, rev 1.10/1.78, addr 3> on usbus1
> kbd2 at ukbd0
> ahci0.0: Found SSD "TS32GMTS400 20140516" serial="B620550018"
> ahci0.0: tags=32/32 satacap=830e satacap2=0086 satafea=054c NCQ=YES capacity=30533.83MB
> ahci0.0: f85=7469 f86=b401 f87=4063 WC=enabled RA=enabled SEC=frozen
> ahci0.2: Found DISK "WDC WD30EZRX-00MMMB0 80.00A80" serial="WD-WCAWZ2969584"
> ahci0.2: tags=32/32 satacap=170e satacap2=0004 satafea=0044 NCQ=YES capacity=2861588.46MB
> ahci0.2: f85=7469 f86=bc41 f87=4123 WC=enabled RA=enabled SEC=frozen
> ahci0.4: Found DISK "WDC WD30EZRX-00MMMB0 80.00A80" serial="WD-WCAWZ2111282"
> ahci0.4: tags=32/32 satacap=170e satacap2=0004 satafea=0044 NCQ=YES capacity=2861588.46MB
> ahci0.4: f85=7469 f86=bc41 f87=4123 WC=enabled RA=enabled SEC=frozen
> ahci0.5: No device detected
> pci0: <serial bus, SMBus> (vendor 0x8086, dev 0x1e22) at device 31.3 irq 18
> acpi_button0: <Power Button> on acpi0
> acpi_tz0: <Thermal Zone> on acpi0
> acpi_tz1: <Thermal Zone> on acpi0
> sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 on acpi0
> sio0: type 16550A
> sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0
> sio1: type 16550A
> cpu0: <ACPI CPU> on acpi0
> ACPI: Dynamic OEM Table Load:
> ACPI: SSDT 0xFFFFFF81D7025200 00083B (v01 PmRef  Cpu0Cst  00003001 INTL 20051117)
> cpu_cst0: <ACPI CPU C-State> on cpu0
> cpu_pst0: <ACPI CPU P-State> on cpu0
> clockmod0: <CPU clock modulation> on cpu0
> perfbias0: <CPU perf-energy bias> on cpu0
> coretemp0: <CPU On-Die Thermal Sensors> on cpu0
> cpu1: <ACPI CPU> on acpi0
> ACPI: Dynamic OEM Table Load:
> ACPI: SSDT 0xFFFFFF81DBEEF140 000303 (v01 PmRef  ApIst    00003000 INTL 20051117)
> ACPI: Dynamic OEM Table Load:
> ACPI: SSDT 0xFFFFFF805BBF7F40 000119 (v01 PmRef  ApCst    00003000 INTL 20051117)
> cpu_cst1: <ACPI CPU C-State> on cpu1
> cpu_pst1: <ACPI CPU P-State> on cpu1
> clockmod1: <CPU clock modulation> on cpu1
> perfbias1: <CPU perf-energy bias> on cpu1
> coretemp1: <CPU On-Die Thermal Sensors> on cpu1
> ACPI: Enabled 6 GPEs in block 00 to 3F
> orm0: <ISA Option ROM> at iomem 0xc0000-0xcefff on isa0
> pmtimer0 on isa0
> atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
> atkbd0: <AT Keyboard> irq 1 on atkbdc0
> kbd0 at atkbd0
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
> sc0: <System console> at flags 0x500 on isa0
> sc0: VGA <16 virtual consoles, flags=0x300>
> hpt27xx: no controller detected.
> CAM: Configuring 4 busses
> CAM: finished configuring all busses
> da0 at ahci0 bus 0 target 0 lun 0
> da0: <SATA TS32GMTS400 2014> Fixed Direct Access SCSI-4 device
> da0: Serial Number B620550018
> da0: 600.000MB/s transfers
> da0: 30533MB (62533296 512 byte sectors: 255H 63S/T 3892C)
> da0: supports TRIM
> da1 at ahci0 bus 2 target 0 lun 0
> da1: <SATA WDC WD30EZRX-00M 80.0> Fixed Direct Access SCSI-4 device
> da1: Serial Number WD-WCAWZ2969584
> da1: 300.000MB/s transfers
> da1: 2861588MB (5860533168 512 byte sectors: 255H 63S/T 364801C)
> da2 at ahci0 bus 4 target 0 lun 0
> da2: <SATA WDC WD30EZRX-00M 80.0> Fixed Direct Access SCSI-4 device
> da2: Serial Number WD-WCAWZ2111282
> da2: 300.000MB/s transfers
> da2: 2861588MB (5860533168 512 byte sectors: 255H 63S/T 364801C)
> da1 part 0: unavailable, bad start or ending lba
> da2 part 0: unavailable, bad start or ending lba
> no B_DEVMAGIC (bootdev=0)
> Mounting root from hammer:serno/B620550018.s1d
> HAMMER(ROOT) recovery check seqno=08a3bb68
> HAMMER(ROOT) recovery range 3000000006f2d038-3000000006f2d038
> HAMMER(ROOT) recovery nexto 3000000006f2d038 endseqno=08a3bb69
> HAMMER(ROOT) mounted clean, no recovery needed
> DMA space used: 10428k, remaining available: 131072k
> Mounting devfs
> HAMMER(DATA) recovery check seqno=2fc8308a
> HAMMER(DATA) recovery range 300000002c2f7648-300000002c2f7648
> HAMMER(DATA) recovery nexto 300000002c2f7648 endseqno=2fc8308b
> HAMMER(DATA) mounted clean, no recovery needed
> HAMMER(BACKUP) recovery check seqno=040ce7dc
> HAMMER(BACKUP) recovery range 300000003552fb48-300000003552fb48
> HAMMER(BACKUP) recovery nexto 300000003552fb48 endseqno=040ce7dd
> HAMMER(BACKUP) mounted clean, no recovery needed
> swap low/high-water marks set to 67683/101525
> pflog0: promiscuous mode enabled
> ugen1.3: <DELL> at usbus1 (disconnected)
> ukbd0: at uhub3, port 2, addr 3 (disconnected)
> ukbd0: detached
> intr 16 on cpu0 at 40001/40000 hz, livelocked limit engaged!
> intr 16 on cpu0 at 11963/20000 hz, livelock removed
> intr 16 on cpu0 at 40001/40000 hz, livelocked limit engaged!
> intr 16 on cpu0 at 10924/20000 hz, livelock removed
> intr 16 on cpu0 at 40001/40000 hz, livelocked limit engaged!
> intr 16 on cpu0 at 19755/20000 hz, livelock removed
> intr 16 on cpu0 at 40001/40000 hz, livelocked limit engaged!
> intr 16 on cpu0 at 14432/20000 hz, livelock removed
> intr 16 on cpu0 at 40001/40000 hz, livelocked limit engaged!
> intr 16 on cpu0 at 15229/20000 hz, livelock removed
> intr 16 on cpu0 at 40001/40000 hz, livelocked limit engaged!
> intr 16 on cpu0 at 5868/20000 hz, livelock removed
> intr 16 on cpu0 at 40001/40000 hz, livelocked limit engaged!
> intr 16 on cpu0 at 15568/20000 hz, livelock removed
> intr 16 on cpu0 at 40001/40000 hz, livelocked limit engaged!
> intr 16 on cpu0 at 1966/20000 hz, livelock removed
> intr 16 on cpu0 at 40001/40000 hz, livelocked limit engaged!
> boot() called on cpu#1
> Switching to cpu #0 for shutdown
> Waiting (max 60 seconds) for system thread swapcached to stop...stopped
> Waiting (max 60 seconds) for system thread vnlru to stop...stopped
> Waiting (max 60 seconds) for system thread consttyd to stop...stopped
> Waiting (max 60 seconds) for system thread bufdaemon to stop...stopped
> Waiting (max 60 seconds) for system thread bufdaemon_hw to stop...stopped
>
> syncing disks...
> done
> vflush: Warning, cannot destroy busy device vnode
> unmount of filesystem mounted from devfs failed (BUSY)
> unmount(0xffffff81d6e23cc0): Forced unmount: 0 namecache references still present
> unmount(0xffffff81d6e23cc0): Forced unmount: 1 mount refs still present
> vflush: Warning, cannot destroy busy device vnode
> unmount of filesystem mounted from devfs failed (BUSY)
> Uptime: 1d20h17m17s
> intr 16 on cpu0 at 15420/20000 hz, livelock removed
> Copyright (c) 2003-2017 The DragonFly Project.
> Copyright (c) 1992-2003 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
>         The Regents of the University of California. All rights reserved.
> DragonFly v4.8.0.1.g86163-RELEASE #4: Tue Mar 28 07:56:27 EST 2017
>     root at dfly.bagdala2.net:/usr/obj/usr/src/sys/X86_64_GENERIC
> i8254 clock: 1193297 Hz
> TSC invariant clock: 1795934560 Hz
> CPU: Intel(R) Celeron(R) CPU 1037U @ 1.80GHz (1795.93-MHz K8-class CPU)
>   Origin = "GenuineIntel"  Id = 0x306a9  Stepping = 9
>   Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
>   Features2=0x5bae3bf<SSE3,PCLMULQDQ,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,POPCNT,TSCDLT,XSAVE>
>   AMD Features=0x28100800<SYSCALL,NX,RDTSCP,LM>
>   AMD Features2=0x1<LAHF>
>   Structured Extended Features=0x281<GSFSBASE,SMEP,ENHMOVSB>
>   Thermal and PM Features=0x75<SENSOR,ARAT,PLN,ECMD,PTM>
>   MONITOR/MWAIT Features=0x3<CST,INTBRK>
> real memory  = 8477464576 (8084 MB)
> avail memory = 7884136448 (7518 MB)
> lapic: divisor index 0, frequency 49886789 Hz
> srat_probe: can't locate SRAT
> Initialize MI interrupts
> TSC testing MP synchronization ...
> cpu1: TSC is not MP synchronized @0
> TSC is not MP synchronized
> VMM: available, disabled by default
> wdog: In-kernel automatic watchdog reset enabled
> kbd1 at kbdmux0
> md0: Malloc disk
> interrupt uses mplock: swi_taskq
> ACPI: RSDP 0x00000000000F0490 000024 (v02 ALASKA)
> ACPI: XSDT 0x00000000DA781070 000064 (v01 ALASKA A M I    01072009 AMI  00010013)
> ACPI: FACP 0x00000000DA78C908 00010C (v05 ALASKA A M I    01072009 AMI  00010013)
> ACPI: DSDT 0x00000000DA781168 00B79B (v02 ALASKA A M I    00000028 INTL 20051117)
> ACPI: FACS 0x00000000DABB7080 000040
> ACPI: APIC 0x00000000DA78CA18 000062 (v03 ALASKA A M I    01072009 AMI  00010013)
> ACPI: FPDT 0x00000000DA78CA80 000044 (v01 ALASKA A M I    01072009 AMI  00010013)
> ACPI: MCFG 0x00000000DA78CAC8 00003C (v01 ALASKA A M I    01072009 MSFT 00000097)
> ACPI: HPET 0x00000000DA78CB08 000038 (v01 ALASKA A M I    01072009 AMI. 00000005)
> ACPI: SSDT 0x00000000DA78CB40 000315 (v01 SataRe SataTabl 00001000 INTL 20091112)
> ACPI: SSDT 0x00000000DA78CE58 000860 (v01 PmRef  Cpu0Ist  00003000 INTL 20051117)
> ACPI: SSDT 0x00000000DA78D6B8 000B22 (v01 PmRef  CpuPm    00003000 INTL 20051117)
> cryptosoft0: <software crypto> on motherboard
> aesni0: No AESNI support.
> padlock0: No ACE support.
> rdrand0: No RdRand support.
> acpi0: <ALASKA A M I> on motherboard
> ACPI: Executed 1 blocks of module-level executable AML code
> ACPI: 4 ACPI AML tables successfully acquired and loaded
> ACPI FADT: SCI testing interrupt mode ...
> ACPI FADT: SCI select level/low
> acpi0: Power Button (fixed)
> acpi_timer0 on acpi0
> acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
> acpi_hpet0: frequency 14318180
> pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
> pci0: <ACPI PCI bus> on pcib0
> vgapci0: <VGA-compatible display> port 0xf000-0xf03f mem 0xe0000000-0xefffffff,0xf7800000-0xf7bfffff irq 11 at device 2.0 on pci0
> vgapci0: Boot video device
> pci0: <simple comms> (vendor 0x8086, dev 0x1e3a) at device 22.0 irq 11
> ehci0: <Intel Panther Point USB 2.0 controller> mem 0xf7d08000-0xf7d083ff irq 11 at device 26.0 on pci0
> usbus0: EHCI version 1.0
> usbus0 on ehci0
> pci0: <multimedia, HDA> (vendor 0x8086, dev 0x1e20) at device 27.0 irq 11
> pcib1: <ACPI PCI-PCI bridge> irq 11 at device 28.0 on pci0
> pci1: <ACPI PCI bus> on pcib1
> usbus0: 480Mbps High Speed USB v2.0
> pcib2: <ACPI PCI-PCI bridge> irq 10 at device 28.2 on pci0
> pci2: <ACPI PCI bus> on pcib2
> re0: <RealTek 8111/8168 PCIe Gigabit Ethernet> port 0xe000-0xe0ff mem 0xf0000000-0xf0003fff,0xf7c00000-0xf7c00fff irq 10 at device 0.0 on pci2
> re0: MAC version 0x2c900000, MACFG 39, support MSI
> re0: bus speed 125MHz
> ugen0.1: <Intel> at usbus0
> uhub0: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0
> re0: MAC address: b8:ae:ed:3c:ce:35
> ehci1: <Intel Panther Point USB 2.0 controller> mem 0xf7d07000-0xf7d073ff irq 11 at device 29.0 on pci0
> usbus1: EHCI version 1.0
> usbus1 on ehci1
> isab0: <PCI-ISA bridge> at device 31.0 on pci0
> isa0: <ISA bus> on isab0
> ahci0: <AHCI-PCI-SATA> port 0xf060-0xf07f,0xf080-0xf083,0xf090-0xf097,0xf0a0-0xf0a3,0xf0b0-0xf0b7 mem 0xf7d06000-0xf7d067ff irq 11 at device 31.2 on pci0
> usbus1: 480Mbps High Speed USB v2.0
> ugen1.1: <Intel> at usbus1
> uhub1: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1
> ahci0: Intel hocus pocus
> ahci0: AHCI 1.3 cap 0xc730ff43<S64A,NCQ,SALP,SAL,SCLO,PMD,SSC,PSC,EMS> cap2 0x4<APST>, 4 ports, 32 tags/port, gen 3 (6Gbps)
> uhub0: 2 ports with 2 removable, self powered
> uhub1: 2 ports with 2 removable, self powered
> ugen0.2: <vendor 0x8087> at usbus0
> uhub2: <vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr 2> on usbus0
> ugen1.2: <vendor 0x8087> at usbus1
> uhub3: <vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr 2> on usbus1
> uhub2: 4 ports with 4 removable, self powered
> uhub3: 4 ports with 4 removable, self powered
> ahci0.0: Found SSD "TS32GMTS400 20140516" serial="B620550018"
> ahci0.0: tags=32/32 satacap=830e satacap2=0086 satafea=054c NCQ=YES capacity=30533.83MB
> ahci0.0: f85=7469 f86=b401 f87=4063 WC=enabled RA=enabled SEC=frozen
> ahci0.2: Found DISK "WDC WD30EZRX-00MMMB0 80.00A80" serial="WD-WCAWZ2969584"
> ahci0.2: tags=32/32 satacap=170e satacap2=0004 satafea=0044 NCQ=YES capacity=2861588.46MB
> ahci0.2: f85=7469 f86=bc41 f87=4123 WC=enabled RA=enabled SEC=frozen
> ahci0.4: Found DISK "WDC WD30EZRX-00MMMB0 80.00A80" serial="WD-WCAWZ2111282"
> ahci0.4: tags=32/32 satacap=170e satacap2=0004 satafea=0044 NCQ=YES capacity=2861588.46MB
> ahci0.4: f85=7469 f86=bc41 f87=4123 WC=enabled RA=enabled SEC=frozen
> ahci0.5: No device detected
> pci0: <serial bus, SMBus> (vendor 0x8086, dev 0x1e22) at device 31.3 irq 10
> acpi_button0: <Power Button> on acpi0
> acpi_tz0: <Thermal Zone> on acpi0
> acpi_tz1: <Thermal Zone> on acpi0
> sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 on acpi0
> sio0: type 16550A
> sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0
> sio1: type 16550A
> cpu0: <ACPI CPU> on acpi0
> ACPI: Dynamic OEM Table Load:
> ACPI: SSDT 0xFFFFFF81D7025200 00083B (v01 PmRef  Cpu0Cst  00003001 INTL 20051117)
> cpu_cst0: <ACPI CPU C-State> on cpu0
> cpu_pst0: <ACPI CPU P-State> on cpu0
> clockmod0: <CPU clock modulation> on cpu0
> perfbias0: <CPU perf-energy bias> on cpu0
> coretemp0: <CPU On-Die Thermal Sensors> on cpu0
> cpu1: <ACPI CPU> on acpi0
> ACPI: Dynamic OEM Table Load:
> ACPI: SSDT 0xFFFFFF81DBE46F40 000303 (v01 PmRef  ApIst    00003000 INTL 20051117)
> ACPI: Dynamic OEM Table Load:
> ACPI: SSDT 0xFFFFFF805BBF7F40 000119 (v01 PmRef  ApCst    00003000 INTL 20051117)
> cpu_cst1: <ACPI CPU C-State> on cpu1
> cpu_pst1: <ACPI CPU P-State> on cpu1
> clockmod1: <CPU clock modulation> on cpu1
> perfbias1: <CPU perf-energy bias> on cpu1
> coretemp1: <CPU On-Die Thermal Sensors> on cpu1
> ACPI: Enabled 6 GPEs in block 00 to 3F
> orm0: <ISA Option ROM> at iomem 0xc0000-0xcefff on isa0
> pmtimer0 on isa0
> atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
> atkbd0: <AT Keyboard> irq 1 on atkbdc0
> kbd0 at atkbd0
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
> sc0: <System console> at flags 0x500 on isa0
> sc0: VGA <16 virtual consoles, flags=0x300>
> hpt27xx: no controller detected.
> CAM: Configuring 4 busses
> CAM: finished configuring all busses
> da0 at ahci0 bus 0 target 0 lun 0
> da0: <SATA TS32GMTS400 2014> Fixed Direct Access SCSI-4 device
> da0: Serial Number B620550018
> da0: 600.000MB/s transfers
> da0: 30533MB (62533296 512 byte sectors: 255H 63S/T 3892C)
> da0: supports TRIM
> da1 at ahci0 bus 2 target 0 lun 0
> da1: <SATA WDC WD30EZRX-00M 80.0> Fixed Direct Access SCSI-4 device
> da1: Serial Number WD-WCAWZ2969584
> da1: 300.000MB/s transfers
> da1: 2861588MB (5860533168 512 byte sectors: 255H 63S/T 364801C)
> da2 at ahci0 bus 4 target 0 lun 0
> da2: <SATA WDC WD30EZRX-00M 80.0> Fixed Direct Access SCSI-4 device
> da2: Serial Number WD-WCAWZ2111282
> da2: 300.000MB/s transfers
> da2: 2861588MB (5860533168 512 byte sectors: 255H 63S/T 364801C)
> da1 part 0: unavailable, bad start or ending lba
> da2 part 0: unavailable, bad start or ending lba
> no B_DEVMAGIC (bootdev=0)
> Mounting root from hammer:serno/B620550018.s1d
> HAMMER(ROOT) recovery check seqno=08b640b2
> HAMMER(ROOT) recovery range 3000000009728c38-3000000009728c38
> HAMMER(ROOT) recovery nexto 3000000009728c38 endseqno=08b640b3
> HAMMER(ROOT) mounted clean, no recovery needed
> DMA space used: 10080k, remaining available: 131072k
> Mounting devfs
> HAMMER(DATA) recovery check seqno=30140895
> HAMMER(DATA) recovery range 3000000025aa8ab8-3000000025aa8ab8
> HAMMER(DATA) recovery nexto 3000000025aa8ab8 endseqno=30140896
> HAMMER(DATA) mounted clean, no recovery needed
> HAMMER(BACKUP) recovery check seqno=0415fb69
> HAMMER(BACKUP) recovery range 3000000006059498-3000000006059498
> HAMMER(BACKUP) recovery nexto 3000000006059498 endseqno=0415fb6a
> HAMMER(BACKUP) mounted clean, no recovery needed
> swap low/high-water marks set to 67683/101525
> pflog0: promiscuous mode enabled
>
>
>
>>
>> On Thu, Apr 20, 2017 at 11:10 AM, Predrag Punosevac
>> <punosevac72 at gmail.com> wrote:
>> > Matthew Dillon wrote:
>> >
>> >> Your BIOS appears to be trying to emulate an ATA controller.  There is
>> >> no AHCI attachment.  Go into setup and see if you can tell your BIOS to
>> >> enable AHCI instead of ATA.
>> >>
>> >> -Matt
>> >
>> > Almost a year later even after adjusting BIOS settings (SATA controller
>> > was trying to emulate ATA controller so I switched to AHCI) I kept
>> > seeing
>> >
>> > intr 16 on cpu0 at 40001/40000 hz, livelocked limit engaged!
>> > intr 16 on cpu0 at 11963/20000 hz, livelock removed
>> >
>> > even on the
>> >
>> > dfly# uname -a DragonFly dfly.bagdala2.net 4.8-RELEASE DragonFly
>> > v4.8.0.1.g86163-RELEASE #4: Tue Mar 28 07:56:27 EST 2017
>> > root at dfly.bagdala2.net:/usr/obj/usr/src/sys/X86_64_GENERIC  x86_64
>> >
>> > Then I stumbled recently on this post
>> >
>> > http://yrabbit.freeshell.org/en/2012/03/04/dragonfly-bsd-under-qemu.html
>> >
>> > and sure enough
>> >
>> > echo 'hw.ioapic_enable=0' >> /boot/loader.conf.local reboot
>> >
>> > made
>> >
>> > intr 16 on cpu0 at 40001/40000 hz, livelocked limit engaged!
>> > intr 16 on cpu0 at 11963/20000 hz, livelock removed
>> >
>> > disapear from dmesg. Unfortunatelly I don't know enough about Advanced
>> > Programmable Interrupt Controller
>> >
>> > https://en.wikipedia.org/wiki/Advanced_Programmable_Interrupt_Controller
>> >
>> > so I am not sure if the above is just bandage for an actual bug which
>> > looks like it should have being fixed
>> >
>> > http://lists.dragonflybsd.org/pipermail/bugs/2012-March/244444.html
>> >
>> >
>> > Thanks,
>> > Predrag
>> >
>> >
>> >
>> >
>> >
>> >>
>> >> On Sat, Apr 16, 2016 at 4:10 PM, Predrag Punosevac
>> >> <punosevac72 at gmail.com>
>> >> wrote:
>> >>
>> >> > Sepherosa Ziehau wrote:
>> >> >
>> >> > > On Tue, Apr 5, 2016 at 11:09 AM, Predrag Punosevac
>> >> > > <punosevac72 at gmail.com> wrote:
>> >> > > > Sepherosa Ziehau <sepherosa at gmail.com> wrote:
>> >> > > >
>> >> > > >> Please post the output of 'vmstat -iv'
>> >> > > >
>> >> > > > dfly# vmstat -iv
>> >> > > > interrupt                                total       rate
>> >> > > > irq4     0: sio0                             0          0
>> >> > > > irq9     0: acpi0                            0          0
>> >> > > > irq16    0: ehci0/atapci0/atapci1  61925216594      35565
>> >> > >
>> >> > >
>> >> > > I'd suspect its EHCI, do you have anything uses USB?  If not,
>> >> disable
>> >> > > the EHCI from BIOS and see whether it works for you or not.
>> >> >
>> >> > I disabled completely USB from BIOS. The error is still there here is
>> >> the
>> >> > new output from vmstat
>> >> >
>> >> > intr 16 on cpu0 at 40001/40000 hz, livelocked limit engaged!
>> >> > dfly# vmstat -iv
>> >> > interrupt                                total       rate
>> >> > irq4     0: sio0                             0          0
>> >> > irq9     0: acpi0                            0          0
>> >> > irq16    0: atapci0/atapci1            7508403      35085
>> >> > irq18    0: re0                            265          1
>> >> > irq192   0: swi_siopoll                      0          0
>> >> > irq196   0: swi_vm                           0          0
>> >> > irq1     1: atkbd0                           7          0
>> >> > irq3     1: sio1                             0          0
>> >> > irq195   1: swi_cambio                      38          0
>> >> > irq197   1: swi_mp_taskq/swi_taskq        1738          8
>> >> > Total                                  7510451      35095
>> >> >
>> >> >
>> >> > Any idea? Looks like DF has a problem with HDD SATA controller.
>> >> >
>> >> > Predrag
>> >> >
>> >> >
>> >> >
>>
>>
>>
>> --
>> Tomorrow Will Never Die



-- 
Tomorrow Will Never Die


More information about the Users mailing list