[DragonFlyBSD - Bug #1579] (Feedback) dfly 2.4.1 does not like HP DL360G4p and Smart Array 6400 with MSA20

bugtracker-admin at leaf.dragonflybsd.org bugtracker-admin at leaf.dragonflybsd.org
Mon Jun 2 14:44:04 PDT 2014


Issue #1579 has been updated by tuxillo.

Description updated
Category set to Unverifiable
Status changed from New to Feedback
Assignee set to tuxillo
Target version set to Unverifiable

Hi,

Moving to unverifiable since we don't have the hardware to test that.

BUT...

I had exactly the same on my HP Proliant Microserver Gen8 when booting with ACPI not loaded. So if anyone has the hardware (HP DL360G4p and Smart Array 6400 or similar) and can test on latest release (3.8 at this moment) or master, please resurrect this issue.

Best regards,
Antonio Huete



----------------------------------------
Bug #1579: dfly 2.4.1 does not like HP DL360G4p and Smart Array 6400 with MSA20
http://bugs.dragonflybsd.org/issues/1579#change-12015

* Author: tomaz.borstnar
* Status: Feedback
* Priority: Normal
* Assignee: tuxillo
* Category: Unverifiable
* Target version: Unverifiable
----------------------------------------
Hello!

	I have a HP DL360G4p machine with 5 gigs of RAM, internal SATA disk and HP SmartArray 6400 controller (2 channels) with 
6400EM card (additional 2 channels attached as daughter card) with MSA20 enclosure with SATA disks - configured as 4 
volumes. Install went fine, but dmesg prints some errors (full dmesg output attached), but here are relevant parts:

bge0: <Broadcom BCM5704C Dual Gigabit Ethernet> mem 0xfddf0000-0xfddfffff irq 7 at device 2.0 on pci2
bge0: CHIP ID 0x21000000; ASIC REV 0x02; CHIP REV 0x21; PCI-X
alignment check failed
miibus0: <MII bus> on bge0
brgphy0: <BCM5704 10/100/1000baseT PHY> on miibus0
brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
bge0: MAC address: 00:15:60:0f:b0:e8
bge1: <Broadcom BCM5704C Dual Gigabit Ethernet> mem 0xfdde0000-0xfddeffff irq 7 at device 2.1 on pci2
bge1: CHIP ID 0x21000000; ASIC REV 0x02; CHIP REV 0x21; PCI-X
alignment check failed
alignment check failed
miibus1: <MII bus> on bge1
brgphy1: <BCM5704 10/100/1000baseT PHY> on miibus1
brgphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
bge1: MAC address: 00:15:60:0f:b0:e7

And...

CAM: Configuring 5 busses
CAM: finished configuring all busses (-2 left)
**WARNING** waiting for the following device to finish configuring:
   xpt:  func=0xc015423d arg=0
**WARNING** waiting for the following device to finish configuring:
   xpt:  func=0xc015423d arg=0
**WARNING** waiting for the following device to finish configuring:
   xpt:  func=0xc015423d arg=0
**WARNING** waiting for the following device to finish configuring:
   xpt:  func=0xc015423d arg=0
**WARNING** waiting for the following device to finish configuring:
   xpt:  func=0xc015423d arg=0
Giving up, interrupt routing is probably hosed

But ciss is seen:
ciss0: <HP Smart Array 6400> port 0x5000-0x50ff mem 0xfdff0000-0xfdff1fff irq 7 at device 4.0 on pci11
ciss1: <HP Smart Array 6400 EM> port 0x5400-0x54ff mem 0xfdf70000-0xfdf71fff irq 5 at device 5.0 on pci11

Anything I can help to test?

Tomaž

---Files--------------------------------
dmesg.txt (7.07 KB)


-- 
You have received this notification because you have either subscribed to it, or are involved in it.
To change your notification preferences, please click here: http://bugs.dragonflybsd.org/my/account




More information about the Bugs mailing list