[DragonFlyBSD - Bug #1579] dfly 2.4.1 does not like HP DL360G4p and Smart Array 6400 with MSA20

Sascha Wildner via Redmine bugtracker-admin at leaf.dragonflybsd.org
Mon Aug 27 00:40:38 PDT 2012


Issue #1579 has been updated by Sascha Wildner.

Description updated
Assignee deleted (0)

Any chance that a current DragonFly could be tested on this box?

----------------------------------------
Bug #1579: dfly 2.4.1 does not like HP DL360G4p and Smart Array 6400 with MSA20
http://bugs.dragonflybsd.org/issues/1579

Author: Tomaz Borstnar
Status: New
Priority: Normal
Assignee: 
Category: 
Target version: 


Hello!

	I have a HP DL360G4p machine with 5 gigs of RAM, internal SATA disk and HP SmartArray 6400 controller (2 channels) with 
6400EM card (additional 2 channels attached as daughter card) with MSA20 enclosure with SATA disks - configured as 4 
volumes. Install went fine, but dmesg prints some errors (full dmesg output attached), but here are relevant parts:

bge0: <Broadcom BCM5704C Dual Gigabit Ethernet> mem 0xfddf0000-0xfddfffff irq 7 at device 2.0 on pci2
bge0: CHIP ID 0x21000000; ASIC REV 0x02; CHIP REV 0x21; PCI-X
alignment check failed
miibus0: <MII bus> on bge0
brgphy0: <BCM5704 10/100/1000baseT PHY> on miibus0
brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
bge0: MAC address: 00:15:60:0f:b0:e8
bge1: <Broadcom BCM5704C Dual Gigabit Ethernet> mem 0xfdde0000-0xfddeffff irq 7 at device 2.1 on pci2
bge1: CHIP ID 0x21000000; ASIC REV 0x02; CHIP REV 0x21; PCI-X
alignment check failed
alignment check failed
miibus1: <MII bus> on bge1
brgphy1: <BCM5704 10/100/1000baseT PHY> on miibus1
brgphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
bge1: MAC address: 00:15:60:0f:b0:e7

And...

CAM: Configuring 5 busses
CAM: finished configuring all busses (-2 left)
**WARNING** waiting for the following device to finish configuring:
   xpt:  func=0xc015423d arg=0
**WARNING** waiting for the following device to finish configuring:
   xpt:  func=0xc015423d arg=0
**WARNING** waiting for the following device to finish configuring:
   xpt:  func=0xc015423d arg=0
**WARNING** waiting for the following device to finish configuring:
   xpt:  func=0xc015423d arg=0
**WARNING** waiting for the following device to finish configuring:
   xpt:  func=0xc015423d arg=0
Giving up, interrupt routing is probably hosed

But ciss is seen:
ciss0: <HP Smart Array 6400> port 0x5000-0x50ff mem 0xfdff0000-0xfdff1fff irq 7 at device 4.0 on pci11
ciss1: <HP Smart Array 6400 EM> port 0x5400-0x54ff mem 0xfdf70000-0xfdf71fff irq 5 at device 5.0 on pci11

Anything I can help to test?

Tomaž


-- 
You have received this notification because you have either subscribed to it, or are involved in it.
To change your notification preferences, please click here: http://bugs.dragonflybsd.org/my/account





More information about the Bugs mailing list